This package aims to provide Detection and Tracking of Moving Objects capabilities to robotic platforms that are equipped with a 2D LIDAR sensor and publish 'sensor_msgs/LaseScan' ROS messages.
Such a scenario would be the one visualized below, in which the black scaled car is equipped with a LIDAR sensor and it needs to track the motion of the red vehicle through the LIDAR measurements.
The output of this package is visualized below and it can be observed that it estimates position, velocity, orientation and dimensions of the red vehicle.
It specializes in tracking of rectangle shaped objects and therefore it is most used in vehicle tracking. The workflow of this package is inspired by the one presented in Kim et al., 2018 [1].
Below you can read a synopsis of its funcion and operation. A more in depth explanation of this package's inner workings is given in this paper.
The detection part of the system is visualized in the following flowchart:
In the clustering step the raw LIDAR measurements are divided to groups/clusters. In this way, the different objects in the environment are differentiatted.
A simple way to do this is by separating clusters, based on the inbetween euclidean distance of LIDAR measurements.
Therefore, if the distance of two consequtive LIDAR measurements is greater than a predefined threshold distance the two points are divided in two separate clusters.
However, since LIDAR measurements become less dense as the distance from the sensor increases, objects
For this reason, the threshold distance should be adapted in a way that it increses in relation with the range distance.
In this system, this is achieved by using the Adaptive Breakpoint Detector algorithm.
Its operation is visualized in the right side of the above figure and the equation that it uses is given below it.
In this step, rectangles are fitted onto the extracted clusters are fitted with rectangles.
This is done to increase the tracking accuracy and shape estimation of rectangular objects.
The algorithm used for rectangle fitting is the Search-Based Rectangle Fitting algorithm developed by Zhang et al., 2017 [2].
After rectangle fitting, L-shapes are extracted from all the rectangles.
L-shapes represent the corner of the rectangle closer to the sensor and its two adjacent sides.
Therefore, every L-shape contains five measurements, the position of the corner point, the orientation of the rectangle (theta) and the length of its sides (L1, L2).
The tracking part of the system is visualized in the following flowchart:
The clusters are tracked between time frames by a Nearest Neighbour data association scheme, with a Euclidean distance criterion.
In cases that the closest corner point of a tracked vehicle changes between measurements, this is detected by comparing the Mahalanobis distance of the four corner points of the vehicle with that of the new L-shape.
The motion of the detected vehicles is tracked based on two kinematic trackers.
A Kalman Filter with a Constant Velocity Model and an Unscented Kalman Filter with a Coordinated-Turn model.
The shape and orientation of the detected vehicles are tracked by a Kalman Filter that contains two models.
The first model is a Constant Shape model and it indicates that the shape of the detected vehicle remains constant.
The second model is a Constant Turn Rate model that indicates that the turn rate of the detected vehicle remains constant, while its orientation depends on the turn rate.
Below you can find a video presentation in which some early features of this package are explained.
This ROS package can be installed in the following way:
- First you should navigate to the source folder of your catkin_ws. For example
cd ~/catkin_ws/src. - Run
git clone [email protected]:kostaskonkk/datmo.git
cd ..
catkin_makeThe datmo package should be now installed to your computer and you will be able to use it after sourcing your workspace.
source devel/setup.bash
You can run a demonstration of the DATMO package by running:
roslaunch datmo example.launch bag:=overtakes
You can run it by typing:
roslaunch datmo datmo.launch
scan(sensor_msgs/LaserScan) - This topic should be created be your LIDAR sensor.
This node can publish a variety of topics but the final configuration depends on the user. By default the majority of the topics are disabled and they should be enabled through the launch file configuration.
datmo/marker_array (visualization_msgs/MarkerArray) - In this topic a variety of Rviz markers are published, which can facilitate in understanding the inner workings of the program.
datmo/box_kf (datmo/TrackArray) - In this topic the output of a Kalman Filter with a Constant Velocity model, which tracks the center of the box that surrounds the clusters is published.\
Note: In case that the marker_array topic is published from a robot and visualized in a computer which has a different version of ROS installed (kinetic, melodic, ...), the msgs will not be published and the datmo node will crash with an md5sum error. To fix this error, you should install on your robot the visualization msgs package of the ROS installation that runs on your computer.
This package uses two custom msgs types datmo/Track and datmo/TrackArray to facilitate the publishing of its results. To my knowledge, at the time of developement, there was no standard ROS messages that accomplishes the same task.
The datmo/Track message has the following structure:
int32 id - object ID, so it is possible to differentiate between different objects during tracking
float32 length - Estimated length of the object
float32 width Estimated width of the object
nav_msgs/Odometry odom - Estimated pose of the object
The datmo/TrackArray message is an array that contains multiple datmo/Track messages, with the goal of efficient publishing.
In case that the pub_markers flag is set to true, this package publishes visualization messages, which can be displayed in Rviz. The following messages are published:
closest_corner - The closest corner point of surrounding vehicles is visualized with a black rectangle.
bounding_box_center - The center of the bounding box is visualized with a yellow rectangle.
velocities - The velocities of the tracked objects are represented with an arrow.\
- "lidar_frame" ("string", default: "laser") - Name of the transformation frame (frame_id) of the LaserScan msgs
- "world_frame" ("string", default: "world") - Name of the world coordinate frame, if it is not available, this value can be set equal to the lidar_frame
- "threshold_distance" ("double", default: "0.2") - This value sets the distance that is used by the clustering algorithm
- "euclidean_distance" ("double", default: "0.25") - This value sets the distance that is used by the euclidean distasnce data association algorithm
- "pub_markers" ("bool", default: "false") - publish of the the vizualization markers
If you use this package or find it useful in your research feel free to add your project in this list:
[1] D. Kim, K. Jo, M. Lee, and M. Sunwoo, “L-shape model switching-based precise motion tracking of moving vehicles using laser scanners,” IEEE Transactions on Intelligent Transportation Systems, vol. 19, no. 2, pp. 598–612, 2018.
[2] X. Zhang, W. Xu, C. Dong, and J. M. Dolan, “Efficient l-shape fitting for vehicle detection using laser scanners,” in 2017 IEEE Intelligent Vehicles Symposium (IV), pp. 54–59, IEEE, 2017.