A complex camera support library for Linux, Android, and ChromeOS
Cameras are complex devices that need heavy hardware image processing operations. Control of the processing is based on advanced algorithms that must run on a programmable processor. This has traditionally been implemented in a dedicated MCU in the camera, but in embedded devices algorithms have been moved to the main CPU to save cost. Blurring the boundary between camera devices and Linux often left the user with no other option than a vendor-specific closed-source solution.
To address this problem the Linux media community has very recently started collaboration with the industry to develop a camera stack that will be open-source-friendly while still protecting vendor core IP. libcamera was born out of that collaboration and will offer modern camera support to Linux-based systems, including traditional Linux distributions, ChromeOS and Android.
Only build libcamera from scratch if you need custom behaviour or the latest features that have not yet reached apt repositories.
If you run Raspberry Pi OS Lite, begin by installing the following packages:
sudo apt install -y python-pip git python3-jinja2
First, install the following libcamera dependencies:
.. code:
sudo apt install -y libboost-dev sudo apt install -y libgnutls28-dev openssl libtiff-dev pybind11-dev sudo apt install -y qtbase5-dev libqt5core5a libqt5widgets sudo apt install -y meson cmake sudo apt install -y python3-yaml python3-ply sudo apt install -y libglib2.0-dev libgstreamer-plugins-base1.0-dev
Now we're ready to build libcamera itself.
Download a local copy of Raspberry Pi's fork of libcamera from GitHub, before building and installing freshly-build binary:
git clone https://github.com/raspberrypi/libcamera.git cd libcamera meson setup build --buildtype=release -Dpipelines=rpi/vc4,rpi/pisp -Dipas=rpi/vc4,rpi/pisp -Dv4l2=true -Dgstreamer=enabled -Dtest=false -Dlc-compliance=disabled -Dcam=disabled -Dqcam=disabled -Ddocumentation=disabled -Dpycamera=enabled ninja -C build install
You can disable the gstreamer plugin by replacing -Dgstreamer=enabled with -Dgstreamer=disabled during the meson build configuration.
If you disable gstreamer, there is no need to install the libglib2.0-dev and libgstreamer-plugins-base1.0-dev dependencies.
On devices with 1GB of memory or less, the build may exceed available memory. Append the -j 1 flag to ninja commands to limit the build to a single process.
This should prevent the build from exceeding available memory on devices like the Raspberry Pi Zero and the Raspberry Pi 3.
libcamera does not yet have a stable binary interface. Always build rpicam-apps after you build libcamera.
You can find more informations at Raspberry Pi libcamera documentation pages.
The following Debian/Ubuntu packages are required for building libcamera. Other distributions may have differing package names:
- A C++ toolchain: [required]
- Either {g++, clang}
- Meson Build system: [required]
- meson (>= 0.60) ninja-build pkg-config
- for the libcamera core: [required]
- libyaml-dev python3-yaml python3-ply python3-jinja2
- for IPA module signing: [recommended]
Either libgnutls28-dev or libssl-dev, openssl
Without IPA module signing, all IPA modules will be isolated in a separate process. This adds an unnecessary extra overhead at runtime.
- for improved debugging: [optional]
libdw-dev libunwind-dev
libdw and libunwind provide backtraces to help debugging assertion failures. Their functions overlap, libdw provides the most detailed information, and libunwind is not needed if both libdw and the glibc backtrace() function are available.
- for device hotplug enumeration: [optional]
- libudev-dev
- for documentation: [optional]
- python3-sphinx doxygen graphviz texlive-latex-extra
- for gstreamer: [optional]
- libgstreamer1.0-dev libgstreamer-plugins-base1.0-dev
- for Python bindings: [optional]
- libpython3-dev pybind11-dev
- for cam: [optional]
libevent-dev is required to support cam, however the following optional dependencies bring more functionality to the cam test tool:
- libdrm-dev: Enables the KMS sink
- libjpeg-dev: Enables MJPEG on the SDL sink
- libsdl2-dev: Enables the SDL sink
- for qcam: [optional]
- libtiff-dev qtbase5-dev qttools5-dev-tools
- for tracing with lttng: [optional]
- liblttng-ust-dev python3-jinja2 lttng-tools
- for android: [optional]
- libexif-dev libjpeg-dev
- for Python bindings: [optional]
- pybind11-dev
- for lc-compliance: [optional]
- libevent-dev libgtest-dev
- for abi-compat.sh: [optional]
- abi-compliance-checker
The cam utility can be used for basic testing. You can list the cameras
detected on the system with cam -l, and capture ten frames from the first
camera and save them to disk with cam -c 1 --capture=10 --file. See
cam -h for more information about the cam tool.
In case of problems, a detailed debug log can be obtained from libcamera by
setting the LIBCAMERA_LOG_LEVELS environment variable:
:~$ LIBCAMERA_LOG_LEVELS=*:DEBUG cam -l
To use the GStreamer plugin from the source tree, use the meson devenv
command. This will create a new shell instance with the GST_PLUGIN_PATH
environment set accordingly.
meson devenv -C build
The debugging tool gst-launch-1.0 can be used to construct a pipeline and
test it. The following pipeline will stream from the camera named "Camera 1"
onto the OpenGL accelerated display element on your system.
gst-launch-1.0 libcamerasrc camera-name="Camera 1" ! queue ! glimagesink
To show the first camera found you can omit the camera-name property, or you can list the cameras and their capabilities using:
gst-device-monitor-1.0 Video
This will also show the supported stream sizes which can be manually selected if desired with a pipeline such as:
gst-launch-1.0 libcamerasrc ! 'video/x-raw,width=1280,height=720' ! \
queue ! glimagesink
The libcamerasrc element has two log categories, named libcamera-provider (for
the video device provider) and libcamerasrc (for the operation of the camera).
All corresponding debug messages can be enabled by setting the GST_DEBUG
environment variable to libcamera*:7.
Presently, to prevent element negotiation failures it is required to specify the colorimetry and framerate as part of your pipeline construction. For instance, to capture and encode as a JPEG stream and receive on another device the following example could be used as a starting point:
gst-launch-1.0 libcamerasrc ! \
video/x-raw,colorimetry=bt709,format=NV12,width=1280,height=720,framerate=30/1 ! \
queue ! jpegenc ! multipartmux ! \
tcpserversink host=0.0.0.0 port=5000
Which can be received on another device over the network with:
gst-launch-1.0 tcpclientsrc host=$DEVICE_IP port=5000 ! \
multipartdemux ! jpegdec ! autovideosink
Several users have reported issues with meson installation, crux of the issue is a potential version mismatch between the version that root uses, and the version that the normal user uses. On calling ninja -C build, it can't find the build.ninja module. This is a snippet of the error message.
ninja: Entering directory `build' ninja: error: loading 'build.ninja': No such file or directory
This can be solved in two ways:
- Don't install meson again if it is already installed system-wide.
- If a version of meson which is different from the system-wide version is already installed, uninstall that meson using pip3, and install again without the --user argument.