PXE
PXE is a standardized client-server solution that boots an agent via network, allowing management tasks in the absence of a running OS. EDK II has PXE Boot specification compliant implementation for UEFI. This feature is commonly referred to as "PXE boot".
This page describes the operation of PXE. There are separate pages describing how to Enable UEFI PXE Boot in EDK II and Configuring PXE Boot Servers for UEFI.
PXE was introduced as part of the Wired for Management Baseline (WfM) Specification by Intel Corporation in 1997. It was described in a separate PXE 1.0 specification since Wired for Management 2.0. Later, the 2.1 update was published in September 1999.
PXE 2.1 describes the IPv4-based network boot process. It does not cover IPv6-based PXE, but this is described in the UEFI 2.2 specification. The UEFI 2.6 specification describes the IPv6-based PXE process in Section 23.3.1. The DHCP6 options used in PXE process are also described in the UEFI specification.
The UEFI specification introduces the following protocols related to PXE boot:
- PXE Base Code Protocol – provides several features to utilize the PXE-compatible devices, for network access and network booting.
- PXE Base Code Callback Protocol – provides callback function which will be invoked when the PXE Base Code Protocol is about to transmit, has received, or is waiting to receive a packet.
- Load File Protocol – loads the boot file to specified buffer, which allows the boot manger to boot the file later.
- Support PXE boot over IPv4 stack, IPv6 stack, or both
- Network Boot Options using PXE are automatically created
- Support PXE Redirection servers (Proxy DHCP servers)
- PXE Vendor Options support (option 43):
- PXE Discovery Control (sub-opt 6, 7)
- PXE Boot Servers (sub-opt 8)
- PXE Boot Menu (sub-opt 9, 10)
There are eight offer types defined in PXEBC_OFFER_TYPE. All of them are supported in IPv4-based PXE. The rules for distinguishing these offers include:
- If the offer is a pure DHCP packet, it is PxeOfferTypeDhcpOnly.
- If the offer does not have DHCP4 option 53, and it contains a DHCP option 67 provides boot file name, it is PxeOfferTypeBootp.
- If the offer has a DHCP4 option 60, or DHCP6 option 16, and the value is starting with “PXEClient”, it is a PXE offer.
- If the PXE offer has a zero “yiaddr” in the DHCP header, it is a proxy offer.
- If the offer has a valid discover vendor option, it is a PXE 1.0 offer.
- If the offer has a valid MTFTP vendor option, it is a WfM 1.1 offer.
The six remaining PXE offers are described below:
| discover vendor option | MTFTP vendor option | N/A | |
|---|---|---|---|
| “PXEClient” available | PxeOfferTypeDhcpPxe10 | PxeOfferTypeDhcpWfm11a | PxeOfferTypeDhcpBinl |
| “PXEClient” available && Yiaddr == 0 | PxeOfferTypeProxyPxe10 | PxeOfferTypeProxyWfm11a | PxeOfferTypeProxyBinl |
Note that “Binl” is a term used in WfM specification and short for “Boot Intervention Network Layer; extended DHCP service”. The offers are selected according to a predefined policy. The priority of the offers is defined in that policy as following:
- PxeOfferTypeDhcpPxe10
- PxeOfferTypeDhcpWfm11a
- PxeOfferTypeProxyPxe10 + PxeOfferTypeDhcpOnly
- PxeOfferTypeProxyWfm11a + PxeOfferTypeDhcpOnly
- PxeOfferTypeDhcpBinl
- PxeOfferTypeProxyBinl + PxeOfferTypeDhcpOnly
- PxeOfferTypeDhcpOnly offer which contains DHCP option 67 for boot file name
- PxeOfferTypeBootp + PxeOfferTypeDhcpOnly
In IPv6-based PXE, only 3 are supported (PxeOfferTypeDhcpBinl, PxeOfferTypeProxyBinl, PxeOfferTypeDhcpOnly).
In IPv4-based PXE, DHCP discovery will be retried four times. The four timeouts are 4, 8, 16 and 32 seconds respectively, to compliant with PXE 2.1 specification. UEFI specification does not define the timeouts for IPv6-based PXE. In current EDKII implementation, DHCPv6 solicit will be retried four times also. The initial retransmission timeout is 4 seconds and maximum retransmission timeout for each retry is 32 seconds. PXE client should wait for the timeout then select most preferred offer among all the received offers.
This section will briefly introduce the PXE boot process, please refer the section 2.2 of PXE v2.1 specification for a detailed step-by-step synopsis of the PXE protocol.
The picture shows a typical IPv4 PXE boot flow (it's from PXE Spec V2.1 Figure 2-1).
Step 1-4 is DHCP protocol with several extended DHCP option tags. The client should broadcast a DHCP Discover message with "PXEClient" extension tags to trigger the DHCP process. Then it should select offers, get the address configuration and boot path information, and complete the standard DHCP protocol by sending a request for the selected address to the server and waiting for the Ack. It might also need to perform DNS resolution to translate the server's host address to IP address.
Step 5-6 takes place between the client and a Boot Server. The client should select and discover a Boot Server from the obtained server list in step 1-4. This phase is not a part of standard DHCP protocol, but uses the DHCP Request and Ack message format as a convenient for communication. The client should send the request message to port 67 (broadcast) or port 4011 (multicast/unicast) of the selected boot server, and wait a DHCP ack for the boot file name and MTFTP configuration parameters.
Step 7-9 is the downloading of the network bootstrap program (NBP). The client will load the NBP into the computer’s local memory using TFTP, verify the image and execute it finally.
- In a Windows Deployment Services (WDS) environment, the NBP is provided as wdsmgfw.efi.
- In a Linux environment, the NBP is provided by UEFI-enabled boot loaders such as GRUB, GRUB2 or ELILO.
Take UEFI PXE with Microsoft WDS as example, the NBP would continue to download several files to client platform. After the downloading finished, the WDS loader calls ExitBootService() and transits to Runtime phase. The OS kernel starts execution and takes over the control to the system. The OS network stack is also started for handling network operations.
Please refer to UEFI PXE Boot Performance Analysis for more details.
Operating systems used to verify EDK II PXE Boot functionality:
- Microsoft Windows 10/8.1/7
- SUSE Linux Enterprise 11 (SP3)
- Red Hat Enterprise Linux 7.0
- PXE uses UDP as transport layer protocol. TCP is not supported.
- PXE is designed to work within a corporate network, not outside of a company firewall.
- PXE uses TFTP and does not support a secure transport method (ex: HTTPS).
- PXE 2.1 specification: http://download.intel.com/design/archives/wfm/downloads/pxespec.pdf
- UEFI 2.6 specification: http://www.uefi.org/sites/default/files/resources/UEFI%20Spec%202_6.pdf
- WfM2.0 specification: http://download.intel.com/design/archives/wfm/downloads/base20.pdf
- UEFI PXE Boot Performance Analysis: https://software.intel.com/sites/default/files/managed/2d/04/intel-uefi-pxe-boot-performance-analysis.pdf
- NetworkPkg Getting Started Guide: https://github.com/tianocore/tianocore.github.io/wiki/NetworkPkg-Getting-Started-Guide