arm64: dts: rockchip: move QCA6174A wakeup pin into its USB node

Currently, we don't coordinate BT USB activity with our handling of the
BT out-of-band wake pin, and instead just use gpio-keys. That causes
problems because we have no way of distinguishing wake activity due to a
BT device (e.g., mouse) vs. the BT controller (e.g., re-configuring wake
mask before suspend). This can cause spurious wake events just because
we, for instance, try to reconfigure the host controller's event mask
before suspending.

We can avoid these synchronization problems by handling the BT wake pin
directly in the btusb driver -- for all activity up until BT controller
suspend(), we simply listen to normal USB activity (e.g., to know the
difference between device and host activity); once we're really ready to
suspend the host controller, there should be no more host activity, and
only *then* do we unmask the GPIO interrupt.

This is already supported by btusb; we just need to describe the wake
pin in the right node.

We list 2 compatible properties, since both PID/VID pairs show up on
Scarlet devices, and they're both essentially identical QCA6174A-based
modules.

Also note that the polarity was wrong before: Qualcomm implemented WAKE
as active high, not active low. We only got away with this because
gpio-keys always reconfigured us as bi-directional edge-triggered.

Finally, we have an external pull-up and a level-shifter on this line
(we didn't notice Qualcomm's polarity in the initial design), so we
can't do pull-down. Switch to pull-none.

Signed-off-by: Brian Norris <[email protected]>
Reviewed-by: Matthias Kaehlcke <[email protected]>
Signed-off-by: Marcel Holtmann <[email protected]>

arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi

@@ -200,6 +200,19 @@
 		pinctrl-0 = <&bl_en>;
 		pwm-delay-us = <10000>;
 	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l>;
+
+		wake_on_bt: wake-on-bt {
+			label = "Wake-on-Bluetooth";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
 };
 
 &ppvar_bigcpu {

arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi

@@ -175,6 +175,21 @@
 		pinctrl-0 = <&dmic_en>;
 		wakeup-delay-ms = <250>;
 	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pen_eject_odl>;
+
+		pen-insert {
+			label = "Pen Insert";
+			/* Insert = low, eject = high */
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_PEN_INSERTED>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+	};
 };
 
 /* pp900_s0 aliases */
@@ -328,20 +343,6 @@ camera: &i2c7 {
 		<400000000>;
 };
 
-&gpio_keys {
-	pinctrl-names = "default";
-	pinctrl-0 = <&bt_host_wake_l>, <&pen_eject_odl>;
-
-	pen-insert {
-		label = "Pen Insert";
-		/* Insert = low, eject = high */
-		gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-		linux,code = <SW_PEN_INSERTED>;
-		linux,input-type = <EV_SW>;
-		wakeup-source;
-	};
-};
-
 &i2c_tunnel {
 	google,remote-bus = <0>;
 };
@@ -437,8 +438,19 @@ camera: &i2c7 {
 	status = "okay";
 };
 
-&wake_on_bt {
-	gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+&usb_host0_ohci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	qca_bt: bluetooth@1 {
+		compatible = "usbcf3,e300", "usb4ca,301a";
+		reg = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "wakeup";
+	};
 };
 
 /* PINCTRL OVERRIDES */
@@ -455,7 +467,7 @@ camera: &i2c7 {
 };
 
 &bt_host_wake_l {
-	rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_up>;
+	rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_none>;
 };
 
 &ec_ap_int_l {

arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi

@@ -269,19 +269,6 @@
 		#clock-cells = <0>;
 	};
 
-	gpio_keys: gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&bt_host_wake_l>;
-
-		wake_on_bt: wake-on-bt {
-			label = "Wake-on-Bluetooth";
-			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			wakeup-source;
-		};
-	};
-
 	max98357a: max98357a {
 		compatible = "maxim,max98357a";
 		pinctrl-names = "default";