NVIDIA device plugin for Kubernetes

This is a forked version of the NVIDIA device plugin for Kubernetes, a component of the Dynamic GPU Partitioner of the open source nos, a module to maximize the utilization of GPU resources in a Kubernetes cluster and cut infrastructure costs.

We have made some changes to the original version to make it support GPU sharing through NVIDIA Multi-Process Service (MPS), which allows spatial sharing of a GPU among multiple processes with memory and compute resources limits.

Specifically, we extended the plugin sharing configuration with the field MPS, which allows to specify which GPUs to share through MPS, in a similar way to the time-slicing sharing configuration. You can find a sample configuration below, which exposes to Kubernetes the GPU with index 0 as two GPU slices (named nvidia.com/gpu-2gb) with 2GB of memory each.

version: v1
flags:
  migStrategy: none
sharing:
  mps: 
    failRequestsGreaterThanOne: true
    resources:
      - name: nvidia.com/gpu
        rename: nvidia.com/gpu-2gb
        memoryGB: 2
        replicas: 2
        devices: ["0"]

During resource allocation, the plugin checks whether the requested GPU ID corresponds to an MPS replicated resource, and if so it mounts the required volumes and sets the required environment variables to make the container use MPS, enforcing the memory and compute resource limits specified in the plugin configuration.

We also changed the installation Helm chart so that MPS sharing can be enabled or disabled through the value mps.enabled. When MPS is enabled, the Chart adds an MPS server sidecar container to the device plugin DaemonSet and sets the GPU mode to EXCLUSIVE_PROCESS.

This forked plugin is a component of nos, the open-source module to efficiently run AI workloads on Kubernetes, increasing GPU utilization, cutting down infrastructure costs and improving workloads performance.

Currently, nos has two main features:

Dynamic GPU partitioning: allow to schedule Pods requesting fractions of GPU. GPU partitioning is performed automatically in real-time based on the Pods pending and running in the cluster, so that Pods can request only the resources that are strictly necessary and GPUs are always fully utilized.
Elastic Resource Quota management: increase the number of Pods running on the cluster by allowing namespaces to borrow quotas of reserved resources from other namespaces as long as they are not using them.

Installation

You can install our forked version of the NVIDIA device plugin for Kubernetes through our Helm chart as follows:

helm install oci://ghcr.io/nebuly-ai/helm-charts/nvidia-device-plugin \
  --version 0.13.0 \
  --generate-name \
  -n nebuly-nvidia \
  --create-namespace

You can find all the available configuration values here.

Installation alongside the NVIDIA device plugin

You can choose to install this plugin alongside the original NVIDIA Device Plugin, but only run it on certain nodes by setting affinity or node selector rules. When you do that, it is important to ensure that only one of the two plugins is running on a node at a time.

For example, this plugin runs on all nodes labelled with nos.nebuly.com/gpu-partitioning=mps by default. If you have an existing installation of the original NVIDIA Device Plugin and want to prevent it from running on nodes with that label, you can upgrade its Helm release by adding the following patch to its values.yaml:

affinity:
  nodeAffinity:
    requiredDuringSchedulingIgnoredDuringExecution:
      nodeSelectorTerms:
        - matchExpressions:
            - key: nos.nebuly.com/gpu-partitioning
              operator: NotIn
              values:
                - mps

About

The NVIDIA device plugin for Kubernetes is a Daemonset that allows you to automatically:

Expose the number of GPUs on each nodes of your cluster
Keep track of the health of your GPUs
Run GPU enabled containers in your Kubernetes cluster.

This repository contains NVIDIA's official implementation of the Kubernetes device plugin.

Please note that:

The NVIDIA device plugin API is beta as of Kubernetes v1.10.
The NVIDIA device plugin is currently lacking
- Comprehensive GPU health checking features
- GPU cleanup features
- ...
Support will only be provided for the official NVIDIA device plugin (and not for forks or other variants of this plugin).

Prerequisites

The list of prerequisites for running the NVIDIA device plugin is described below:

NVIDIA drivers ~= 384.81
nvidia-docker >= 2.0 || nvidia-container-toolkit >= 1.7.0 (>= 1.11.0 to use integrated GPUs on Tegra-based systems)
nvidia-container-runtime configured as the default low-level runtime
Kubernetes version >= 1.10

Quick Start

Preparing your GPU Nodes

The following steps need to be executed on all your GPU nodes. This README assumes that the NVIDIA drivers and the nvidia-container-toolkit have been pre-installed. It also assumes that you have configured the nvidia-container-runtime as the default low-level runtime to use.

Please see: https://docs.nvidia.com/datacenter/cloud-native/container-toolkit/install-guide.html

Example for debian-based systems with `docker` and `containerd`

Install the `nvidia-container-toolkit`

distribution=$(. /etc/os-release;echo $ID$VERSION_ID)
curl -s -L https://nvidia.github.io/libnvidia-container/gpgkey | sudo apt-key add -
curl -s -L https://nvidia.github.io/libnvidia-container/$distribution/libnvidia-container.list | sudo tee /etc/apt/sources.list.d/libnvidia-container.list

sudo apt-get update && sudo apt-get install -y nvidia-container-toolkit

Configure `docker`

When running kubernetes with docker, edit the config file which is usually present at /etc/docker/daemon.json to set up nvidia-container-runtime as the default low-level runtime:

{
    "default-runtime": "nvidia",
    "runtimes": {
        "nvidia": {
            "path": "/usr/bin/nvidia-container-runtime",
            "runtimeArgs": []
        }
    }
}

And then restart docker:

$ sudo systemctl restart docker

Configure `containerd`

When running kubernetes with containerd, edit the config file which is usually present at /etc/containerd/config.toml to set up nvidia-container-runtime as the default low-level runtime:

version = 2
[plugins]
  [plugins."io.containerd.grpc.v1.cri"]
    [plugins."io.containerd.grpc.v1.cri".containerd]
      default_runtime_name = "nvidia"

      [plugins."io.containerd.grpc.v1.cri".containerd.runtimes]
        [plugins."io.containerd.grpc.v1.cri".containerd.runtimes.nvidia]
          privileged_without_host_devices = false
          runtime_engine = ""
          runtime_root = ""
          runtime_type = "io.containerd.runc.v2"
          [plugins."io.containerd.grpc.v1.cri".containerd.runtimes.nvidia.options]
            BinaryName = "/usr/bin/nvidia-container-runtime"

And then restart containerd:

$ sudo systemctl restart containerd

Enabling GPU Support in Kubernetes

Once you have configured the options above on all the GPU nodes in your cluster, you can enable GPU support by deploying the following Daemonset:

$ kubectl create -f https://raw.githubusercontent.com/NVIDIA/k8s-device-plugin/v0.14.0/nvidia-device-plugin.yml

Note: This is a simple static daemonset meant to demonstrate the basic features of the nvidia-device-plugin. Please see the instructions below for Deployment via helm when deploying the plugin in a production setting.

Running GPU Jobs

With the daemonset deployed, NVIDIA GPUs can now be requested by a container using the nvidia.com/gpu resource type:

$ cat <<EOF | kubectl apply -f -
apiVersion: v1
kind: Pod
metadata:
  name: gpu-pod
spec:
  restartPolicy: Never
  containers:
    - name: cuda-container
      image: nvcr.io/nvidia/k8s/cuda-sample:vectoradd-cuda10.2
      resources:
        limits:
          nvidia.com/gpu: 1 # requesting 1 GPU
  tolerations:
  - key: nvidia.com/gpu
    operator: Exists
    effect: NoSchedule
EOF

$ kubectl logs gpu-pod
[Vector addition of 50000 elements]
Copy input data from the host memory to the CUDA device
CUDA kernel launch with 196 blocks of 256 threads
Copy output data from the CUDA device to the host memory
Test PASSED
Done

WARNING: if you don't request GPUs when using the device plugin with NVIDIA images all the GPUs on the machine will be exposed inside your container.

Configuring the NVIDIA device plugin binary

The NVIDIA device plugin has a number of options that can be configured for it. These options can be configured as command line flags, environment variables, or via a config file when launching the device plugin. Here we explain what each of these options are and how to configure them directly against the plugin binary. The following section explains how to set these configurations when deploying the plugin via helm.

As command line flags or envvars

Flag	Envvar	Default Value
`--mig-strategy`	`$MIG_STRATEGY`	`"none"`
`--fail-on-init-error`	`$FAIL_ON_INIT_ERROR`	`true`
`--nvidia-driver-root`	`$NVIDIA_DRIVER_ROOT`	`"/"`
`--pass-device-specs`	`$PASS_DEVICE_SPECS`	`false`
`--device-list-strategy`	`$DEVICE_LIST_STRATEGY`	`"envvar"`
`--device-id-strategy`	`$DEVICE_ID_STRATEGY`	`"uuid"`
`--config-file`	`$CONFIG_FILE`	`""`

As a configuration file

version: v1
flags:
  migStrategy: "none"
  failOnInitError: true
  nvidiaDriverRoot: "/"
  plugin:
    passDeviceSpecs: false
    deviceListStrategy: "envvar"
    deviceIDStrategy: "uuid"

Note: The configuration file has an explicit plugin section because it is a shared configuration between the plugin and gpu-feature-discovery. All options inside the plugin section are specific to the plugin. All options outside of this section are shared.

Configuration Option Details

MIG_STRATEGY: the desired strategy for exposing MIG devices on GPUs that support it

[none | single | mixed] (default 'none')

The MIG_STRATEGY option configures the daemonset to be able to expose Multi-Instance GPUs (MIG) on GPUs that support them. More information on what these strategies are and how they should be used can be found in Supporting Multi-Instance GPUs (MIG) in Kubernetes.

Note: With a MIG_STRATEGY of mixed, you will have additional resources available to you of the form nvidia.com/mig-<slice_count>g.<memory_size>gb that you can set in your pod spec to get access to a specific MIG device.

FAIL_ON_INIT_ERROR: fail the plugin if an error is encountered during initialization, otherwise block indefinitely

(default 'true')

When set to true, the FAIL_ON_INIT_ERROR option fails the plugin if an error is encountered during initialization. When set to false, it prints an error message and blocks the plugin indefinitely instead of failing. Blocking indefinitely follows legacy semantics that allow the plugin to deploy successfully on nodes that don't have GPUs on them (and aren't supposed to have GPUs on them) without throwing an error. In this way, you can blindly deploy a daemonset with the plugin on all nodes in your cluster, whether they have GPUs on them or not, without encountering an error. However, doing so means that there is no way to detect an actual error on nodes that are supposed to have GPUs on them. Failing if an initialization error is encountered is now the default and should be adopted by all new deployments.

NVIDIA_DRIVER_ROOT: the root path for the NVIDIA driver installation

(default '/')

When the NVIDIA drivers are installed directly on the host, this should be set to '/'. When installed elsewhere (e.g. via a driver container), this should be set to the root filesystem where the drivers are installed (e.g. '/run/nvidia/driver').

Note: This option is only necessary when used in conjunction with the $PASS_DEVICE_SPECS option described below. It tells the plugin what prefix to add to any device file paths passed back as part of the device specs.

PASS_DEVICE_SPECS: pass the paths and desired device node permissions for any NVIDIA devices being allocated to the container

(default 'false')

This option exists for the sole purpose of allowing the device plugin to interoperate with the CPUManager in Kubernetes. Setting this flag also requires one to deploy the daemonset with elevated privileges, so only do so if you know you need to interoperate with the CPUManager.

DEVICE_LIST_STRATEGY: the desired strategy for passing the device list to the underlying runtime

[envvar | volume-mounts] (default 'envvar')

The DEVICE_LIST_STRATEGY flag allows one to choose which strategy the plugin will use to advertise the list of GPUs allocated to a container. This is traditionally done by setting the NVIDIA_VISIBLE_DEVICES environment variable as described here. This strategy can be selected via the (default) envvar option. Support has been added to the nvidia-container-toolkit to also allow passing the list of devices as a set of volume mounts instead of as an environment variable. This strategy can be selected via the volume-mounts option. Details for the rationale behind this strategy can be found here.

DEVICE_ID_STRATEGY: the desired strategy for passing device IDs to the underlying runtime

[uuid | index] (default 'uuid')

The DEVICE_ID_STRATEGY flag allows one to choose which strategy the plugin will use to pass the device ID of the GPUs allocated to a container. The device ID has traditionally been passed as the UUID of the GPU. This flag lets a user decide if they would like to use the UUID or the index of the GPU (as seen in the output of nvidia-smi) as the identifier passed to the underlying runtime. Passing the index may be desirable in situations where pods that have been allocated GPUs by the plugin get restarted with different physical GPUs attached to them.

CONFIG_FILE: point the plugin at a configuration file instead of relying on command line flags or environment variables

(default '')

The order of precedence for setting each option is (1) command line flag, (2) environment variable, (3) configuration file. In this way, one could use a pre-defined configuration file, but then override the values set in it at launch time. As described below, a ConfigMap can be used to point the plugin at a desired configuration file when deploying via helm.

Shared Access to GPUs with CUDA Time-Slicing

The NVIDIA device plugin allows oversubscription of GPUs through a set of extended options in its configuration file. Under the hood, CUDA time-slicing is used to allow workloads that land on oversubscribed GPUs to interleave with one another. However, nothing special is done to isolate workloads that are granted replicas from the same underlying GPU, and each workload has access to the GPU memory and runs in the same fault-domain as of all the others (meaning if one workload crashes, they all do).

These extended options can be seen below:

version: v1
sharing:
  timeSlicing:
    renameByDefault: <bool>
    failRequestsGreaterThanOne: <bool>
    resources:
    - name: <resource-name>
      replicas: <num-replicas>
    ...

That is, for each named resource under sharing.timeSlicing.resources, a number of replicas can now be specified for that resource type. These replicas represent the number of shared accesses that will be granted for a GPU represented by that resource type.

If renameByDefault=true, then each resource will be advertised under the name <resource-name>.shared instead of simply <resource-name>.

If failRequestsGreaterThanOne=true, then the plugin will fail to allocate any shared resources to a container if they request more than one. The container’s pod will fail with an UnexpectedAdmissionError and need to be manually deleted, updated, and redeployed.

For example:

version: v1
sharing:
  timeSlicing:
    resources:
    - name: nvidia.com/gpu
      replicas: 10

If this configuration were applied to a node with 8 GPUs on it, the plugin would now advertise 80 nvidia.com/gpu resources to Kubernetes instead of 8.

$ kubectl describe node
...
Capacity:
  nvidia.com/gpu: 80
...

Likewise, if the following configuration were applied to a node, then 80 nvidia.com/gpu.shared resources would be advertised to Kubernetes instead of 8 nvidia.com/gpu resources.

version: v1
sharing:
  timeSlicing:
    renameByDefault: true
    resources:
    - name: nvidia.com/gpu
      replicas: 10
    ...

$ kubectl describe node
...
Capacity:
  nvidia.com/gpu.shared: 80
...

In both cases, the plugin simply creates 10 references to each GPU and indiscriminately hands them out to anyone that asks for them.

If failRequestsGreaterThanOne=true were set in either of these configurations and a user requested more than one nvidia.com/gpu or nvidia.com/gpu.shared resource in their pod spec, then the container would fail with the resulting error:

$ kubectl describe pod gpu-pod
...
Events:
  Type     Reason                    Age   From               Message
  ----     ------                    ----  ----               -------
  Warning  UnexpectedAdmissionError  13s   kubelet            Allocate failed due to rpc error: code = Unknown desc = request for 'nvidia.com/gpu: 2' too large: maximum request size for shared resources is 1, which is unexpected
...

Note: Unlike with "normal" GPU requests, requesting more than one shared GPU does not imply that you will get guaranteed access to a proportional amount of compute power. It only implies that you will get access to a GPU that is shared by other clients (each of which has the freedom to run as many processes on the underlying GPU as they want). Under the hood CUDA will simply give an equal share of time to all of the GPU processes across all of the clients. The failRequestsGreaterThanOne flag is meant to help users understand this subtlety, by treating a request of 1 as an access request rather than an exclusive resource request. Setting failRequestsGreaterThanOne=true is recommended, but it is set to false by default to retain backwards compatibility.

As of now, the only supported resource available for time-slicing are nvidia.com/gpu as well as any of the resource types that emerge from configuring a node with the mixed MIG strategy.

For example, the full set of time-sliceable resources on a T4 card would be:

nvidia.com/gpu

And the full set of time-sliceable resources on an A100 40GB card would be:

nvidia.com/gpu
nvidia.com/mig-1g.5gb
nvidia.com/mig-2g.10gb
nvidia.com/mig-3g.20gb
nvidia.com/mig-7g.40gb

Likewise, on an A100 80GB card, they would be:

nvidia.com/gpu
nvidia.com/mig-1g.10gb
nvidia.com/mig-2g.20gb
nvidia.com/mig-3g.40gb
nvidia.com/mig-7g.80gb

Deployment via `helm`

The preferred method to deploy the device plugin is as a daemonset using helm. Instructions for installing helm can be found here.

Begin by setting up the plugin's helm repository and updating it at follows:

$ helm repo add nvdp https://nvidia.github.io/k8s-device-plugin
$ helm repo update

Then verify that the latest release (v0.14.0) of the plugin is available:

$ helm search repo nvdp --devel
NAME                     	  CHART VERSION  APP VERSION	DESCRIPTION
nvdp/nvidia-device-plugin	  0.14.0	 0.14.0		A Helm chart for ...

Once this repo is updated, you can begin installing packages from it to deploy the nvidia-device-plugin helm chart.

The most basic installation command without any options is then:

helm upgrade -i nvdp nvdp/nvidia-device-plugin \
  --namespace nvidia-device-plugin \
  --create-namespace \
  --version 0.14.0

Note: You only need the to pass the --devel flag to helm search repo and the --version flag to helm upgrade -i if this is a pre-release version (e.g. <version>-rc.1). Full releases will be listed without this.

Configuring the device plugin's `helm` chart

The helm chart for the latest release of the plugin (v0.14.0) includes a number of customizable values.

Prior to v0.12.0 the most commonly used values were those that had direct mappings to the command line options of the plugin binary. As of v0.12.0, the preferred method to set these options is via a ConfigMap. The primary use case of the original values is then to override an option from the ConfigMap if desired. Both methods are discussed in more detail below.

The full set of values that can be set are found here: here.

Passing configuration to the plugin via a `ConfigMap`.

In general, we provide a mechanism to pass multiple configuration files to to the plugin's helm chart, with the ability to choose which configuration file should be applied to a node via a node label.

In this way, a single chart can be used to deploy each component, but custom configurations can be applied to different nodes throughout the cluster.

There are two ways to provide a ConfigMap for use by the plugin:

Via an external reference to a pre-defined ConfigMap
As a set of named config files to build an integrated ConfigMap associated with the chart

These can be set via the chart values config.name and config.map respectively. In both cases, the value config.default can be set to point to one of the named configs in the ConfigMap and provide a default configuration for nodes that have not been customized via a node label (more on this later).

Single Config File Example

As an example, create a valid config file on your local filesystem, such as the following:

cat << EOF > /tmp/dp-example-config0.yaml
version: v1
flags:
  migStrategy: "none"
  failOnInitError: true
  nvidiaDriverRoot: "/"
  plugin:
    passDeviceSpecs: false
    deviceListStrategy: envvar
    deviceIDStrategy: uuid
EOF

And deploy the device plugin via helm (pointing it at this config file and giving it a name):

$ helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set-file config.map.config=/tmp/dp-example-config0.yaml

Under the hood this will deploy a ConfigMap associated with the plugin and put the contents of the dp-example-config0.yaml file into it, using the name config as its key. It will then start the plugin such that this config gets applied when the plugin comes online.

If you don’t want the plugin’s helm chart to create the ConfigMap for you, you can also point it at a pre-created ConfigMap as follows:

$ kubectl create ns nvidia-device-plugin

$ kubectl create cm -n nvidia-device-plugin nvidia-plugin-configs \
    --from-file=config=/tmp/dp-example-config0.yaml

$ helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set config.name=nvidia-plugin-configs

Multiple Config File Example

For multiple config files, the procedure is similar.

Create a second config file with the following contents:

cat << EOF > /tmp/dp-example-config1.yaml
version: v1
flags:
  migStrategy: "mixed" # Only change from config0.yaml
  failOnInitError: true
  nvidiaDriverRoot: "/"
  plugin:
    passDeviceSpecs: false
    deviceListStrategy: envvar
    deviceIDStrategy: uuid
EOF

And redeploy the device plugin via helm (pointing it at both configs with a specified default).

$ helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set config.default=config0 \
    --set-file config.map.config0=/tmp/dp-example-config0.yaml \
    --set-file config.map.config1=/tmp/dp-example-config1.yaml

As before, this can also be done with a pre-created ConfigMap if desired:

$ kubectl create ns nvidia-device-plugin

$ kubectl create cm -n nvidia-device-plugin nvidia-plugin-configs \
    --from-file=config0=/tmp/dp-example-config0.yaml \
    --from-file=config1=/tmp/dp-example-config1.yaml

$ helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set config.default=config0 \
    --set config.name=nvidia-plugin-configs

Note: If the config.default flag is not explicitly set, then a default value will be inferred from the config if one of the config names is set to 'default'. If neither of these are set, then the deployment will fail unless there is only one config provided. In the case of just a single config being provided, it will be chosen as the default because there is no other option.

Updating Per-Node Configuration With a Node Label

With this setup, plugins on all nodes will have config0 configured for them by default. However, the following label can be set to change which configuration is applied:

kubectl label nodes <node-name> –-overwrite \
    nvidia.com/device-plugin.config=<config-name>

For example, applying a custom config for all nodes that have T4 GPUs installed on them might be:

kubectl label node \
    --overwrite \
    --selector=nvidia.com/gpu.product=TESLA-T4 \
    nvidia.com/device-plugin.config=t4-config

Note: This label can be applied either before or after the plugin is started to get the desired configuration applied on the node. Anytime it changes value, the plugin will immediately be updated to start serving the desired configuration. If it is set to an unknown value, it will skip reconfiguration. If it is ever unset, it will fallback to the default.

Setting other helm chart values

As mentioned previously, the device plugin's helm chart continues to provide direct values to set the configuration options of the plugin without using a ConfigMap. These should only be used to set globally applicable options (which should then never be embedded in the set of config files provided by the ConfigMap), or used to override these options as desired.

These values are as follows:

  migStrategy:
      the desired strategy for exposing MIG devices on GPUs that support it
      [none | single | mixed] (default "none")
  failOnInitError:
      fail the plugin if an error is encountered during initialization, otherwise block indefinitely
      (default 'true')
  compatWithCPUManager:
      run with escalated privileges to be compatible with the static CPUManager policy
      (default 'false')
  deviceListStrategy:
      the desired strategy for passing the device list to the underlying runtime
      [envvar | volume-mounts] (default "envvar")
  deviceIDStrategy:
      the desired strategy for passing device IDs to the underlying runtime
      [uuid | index] (default "uuid")
  nvidiaDriverRoot:
      the root path for the NVIDIA driver installation (typical values are '/' or '/run/nvidia/driver')

Note: There is no value that directly maps to the PASS_DEVICE_SPECS configuration option of the plugin. Instead a value called compatWithCPUManager is provided which acts as a proxy for this option. It both sets the PASS_DEVICE_SPECS option of the plugin to true AND makes sure that the plugin is started with elevated privileges to ensure proper compatibility with the CPUManager.

Besides these custom configuration options for the plugin, other standard helm chart values that are commonly overridden are:

  legacyDaemonsetAPI:
      use the legacy daemonset API version 'extensions/v1beta1'
      (default 'false')
  runtimeClassName:
      the runtimeClassName to use, for use with clusters that have multiple runtimes. (typical value is 'nvidia')

Please take a look in the values.yaml file to see the full set of overridable parameters for the device plugin.

Examples of setting these options include:

Enabling compatibility with the CPUManager and running with a request for 100ms of CPU time and a limit of 512MB of memory.

$ helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set compatWithCPUManager=true \
    --set resources.requests.cpu=100m \
    --set resources.limits.memory=512Mi

Using the legacy Daemonset API (only available on Kubernetes < v1.16):

$ helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set legacyDaemonsetAPI=true

Enabling compatibility with the CPUManager and the mixed migStrategy

$ helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set compatWithCPUManager=true \
    --set migStrategy=mixed

Deploying with gpu-feature-discovery for automatic node labels

As of v0.12.0, the device plugin's helm chart has integrated support to deploy gpu-feature-discovery (GFD) as a subchart. One can use GFD to automatically generate labels for the set of GPUs available on a node. Under the hood, it leverages Node Feature Discovery to perform this labeling.

To enable it, simply set gfd.enabled=true during helm install.

helm upgrade -i nvdp nvdp/nvidia-device-plugin \
    --version=0.14.0 \
    --namespace nvidia-device-plugin \
    --create-namespace \
    --set gfd.enabled=true

Under the hood this will also deploy node-feature-discovery (NFD) since it is a prerequisite of GFD. If you already have NFD deployed on your cluster and do not wish for it to be pulled in by this installation, you can disable it with nfd.enabled=false.

In addition to the standard node labels applied by GFD, the following label will also be included when deploying the plugin with the time-slicing extensions described above.

nvidia.com/<resource-name>.replicas = <num-replicas>

Additionally, the nvidia.com/<resource-name>.product will be modified as follows if renameByDefault=false.

nvidia.com/<resource-name>.product = <product name>-SHARED

Using these labels, users have a way of selecting a shared vs. non-shared GPU in the same way they would traditionally select one GPU model over another. That is, the SHARED annotation ensures that a nodeSelector can be used to attract pods to nodes that have shared GPUs on them.

Since having renameByDefault=true already encodes the fact that the resource is shared on the resource name , there is no need to annotate the product name with SHARED. Users can already find the shared resources they need by simply requesting it in their pod spec.

Note: When running with renameByDefault=false and migStrategy=single both the MIG profile name and the new SHARED annotation will be appended to the product name, e.g.:

nvidia.com/gpu.product = A100-SXM4-40GB-MIG-1g.5gb-SHARED

Deploying via `helm install` with a direct URL to the `helm` package

If you prefer not to install from the nvidia-device-plugin helm repo, you can run helm install directly against the tarball of the plugin's helm package. The example below installs the same chart as the method above, except that it uses a direct URL to the helm chart instead of via the helm repo.

Using the default values for the flags:

$ helm upgrade -i nvdp \
    --namespace nvidia-device-plugin \
    --create-namespace \
    https://nvidia.github.io/k8s-device-plugin/stable/nvidia-device-plugin-0.14.0.tgz

Building and Running Locally

The next sections are focused on building the device plugin locally and running it. It is intended purely for development and testing, and not required by most users. It assumes you are pinning to the latest release tag (i.e. v0.14.0), but can easily be modified to work with any available tag or branch.

With Docker

Build

Option 1, pull the prebuilt image from Docker Hub:

$ docker pull nvcr.io/nvidia/k8s-device-plugin:v0.14.0
$ docker tag nvcr.io/nvidia/k8s-device-plugin:v0.14.0 nvcr.io/nvidia/k8s-device-plugin:devel

Option 2, build without cloning the repository:

$ docker build \
    -t nvcr.io/nvidia/k8s-device-plugin:devel \
    -f deployments/container/Dockerfile.ubuntu \
    https://github.com/NVIDIA/k8s-device-plugin.git#v0.14.0

Option 3, if you want to modify the code:

$ git clone https://github.com/NVIDIA/k8s-device-plugin.git && cd k8s-device-plugin
$ docker build \
    -t nvcr.io/nvidia/k8s-device-plugin:devel \
    -f deployments/container/Dockerfile.ubuntu \
    .

Run

Without compatibility for the CPUManager static policy:

$ docker run \
    -it \
    --security-opt=no-new-privileges \
    --cap-drop=ALL \
    --network=none \
    -v /var/lib/kubelet/device-plugins:/var/lib/kubelet/device-plugins \
    nvcr.io/nvidia/k8s-device-plugin:devel

With compatibility for the CPUManager static policy:

$ docker run \
    -it \
    --privileged \
    --network=none \
    -v /var/lib/kubelet/device-plugins:/var/lib/kubelet/device-plugins \
    nvcr.io/nvidia/k8s-device-plugin:devel --pass-device-specs

Without Docker

Build

$ C_INCLUDE_PATH=/usr/local/cuda/include LIBRARY_PATH=/usr/local/cuda/lib64 go build

Run

Without compatibility for the CPUManager static policy:

$ ./k8s-device-plugin

With compatibility for the CPUManager static policy:

$ ./k8s-device-plugin --pass-device-specs

Changelog

Version v0.14.0

Promote v0.14.0-rc.3 to v0.14.0
Bumped nvidia-container-toolkit dependency to latest version for newer CDI spec generation code

Version v0.14.0-rc.3

Removed --cdi-enabled config option and instead trigger CDI injection based on cdi-annotation strategy.
Bumped go-nvlib dependency to latest version for support of new MIG profiles.
Added cdi-annotation-prefix config option to control how CDI annotations are generated.
Renamed driver-root-ctr-path config option added in v0.14.0-rc.1 to container-driver-root.
Updated GFD subchart to version 0.8.0-rc.2

Version v0.14.0-rc.2

Fix bug from v0.14.0-rc.1 when using cdi-enabled=false

Version v0.14.0-rc.1

Added --cdi-enabled flag to GPU Device Plugin. With this enabled, the device plugin will generate CDI specifications for available NVIDIA devices. Allocation will add CDI anntiations (cdi.k8s.io/*) to the response. These are read by a CDI-enabled runtime to make the required modifications to a container being created.
Updated GFD subchart to version 0.8.0-rc.1
Bumped Golang version to 1.20.1
Bumped CUDA base images version to 12.1.0
Switched to klog for logging
Added a static deployment file for Microshift

Version v0.13.0

Promote v0.13.0-rc.3 to v0.13.0
Fail on startup if no valid resources are detected
Ensure that display adapters are skipped when enumerating devices
Bump GFD subchart to version 0.7.0

Version v0.13.0-rc.3

Use nodeAffinity instead of nodeSelector by default in daemonsets
Mount /sys instead of /sys/class/dmi/id/product_name in GPU Feature Discovery daemonset
Bump GFD subchart to version 0.7.0-rc.3

Version v0.13.0-rc.2

Bump cuda base image to 11.8.0
Use consistent indentation in YAML manifests
Fix bug from v0.13.0-rc.1 when using mig-strategy="mixed"
Add logged error message if setting up health checks fails
Support MIG devices with 1g.10gb+me profile
Distribute replicas evenly across GPUs during allocation
Bump GFD subchart to version 0.7.0-rc.2

Version v0.13.0-rc.1

Improve health checks to detect errors when waiting on device events
Log ECC error events detected during health check
Add the GIT sha to version information for the CLI and container images
Use NVML interfaces from go-nvlib to query devices
Refactor plugin creation from resources
Add a CUDA-based resource manager that can be used to expose integrated devices on Tegra-based systems
Bump GFD subchart to version 0.7.0-rc.1

Version v0.12.3

Bump cuda base image to 11.7.1
Remove CUDA compat libs from the device-plugin image in favor of libs installed by the driver
Fix securityContext.capabilities indentation
Add namespace override for multi-namespace deployments

Version v0.12.2

Add an 'empty' config fallback (but don't apply it by default)
Make config fallbacks for config-manager a configurable, ordered list
Allow an empty config file and default to "version: v1"
Bump GFD subchart to version 0.6.1
Move NFD servicAccount info under 'master' in helm chart
Make priorityClassName configurable through helm
Fix assertions for panicking on uniformity with migStrategy=single
Fix example configmap settings in values.yaml file

Version v0.12.1

Exit the plugin and GFD sidecar containers on error instead of logging and continuing
Only force restart of daemonsets when using config file and allow overrides
Fix bug in calculation for GFD security context in helm chart

Version v0.12.0

Promote v0.12.0-rc.6 to v0.12.0
Update README.md with all of the v0.12.0 features

Version v0.12.0-rc.6

Send SIGHUP from GFD sidecar to GFD main container on config change
Reuse main container's securityContext in sidecar containers
Update GFD subchart to v0.6.0-rc.1
Bump CUDA base image version to 11.7.0
Add a flag called FailRequestsGreaterThanOne for TimeSlicing resources

Version v0.12.0-rc.5

Allow either an external ConfigMap name or a set of configs in helm
Handle cases where no default config is specified to config-manager
Update API used to pass config files to helm to use map instead of list
Fix bug that wasn't properly stopping plugins across a soft restart

Version v0.12.0-rc.4

Make GFD and NFD (optional) subcharts of the device plugin's helm chart
Add new config-manager binary to run as sidecar and update the plugin's configuration via a node label
Add support to helm to provide multiple config files for the config map
Refactor main to allow configs to be reloaded across a (soft) restart
Add field for TimeSlicing.RenameByDefault to rename all replicated resources to <resource-name>.shared
Disable support for resource-renaming in the config (will no longer be part of this release)

Version v0.12.0-rc.3

Add ability to parse Duration fields from config file
Omit either the Plugin or GFD flags from the config when not present
Fix bug when falling back to none strategy from single strategy

Version v0.12.0-rc.2

Move MigStrategy from Sharing.Mig.Strategy back to Flags.MigStrategy
Remove timeSlicing.strategy and any allocation policies built around it
Add support for specifying a config file to the helm chart

Version v0.12.0-rc.1

Add API for specifying time-slicing parameters to support GPU sharing
Add API for specifying explicit resource naming in the config file
Update config file to be used across plugin and GFD
Stop publishing images to dockerhub (now only published to nvcr.io)
Add NVIDIA_MIG_MONITOR_DEVICES=all to daemonset envvars when mig mode is enabled
Print the plugin configuration at startup
Add the ability to load the plugin configuration from a file
Remove deprecated tolerations for critical-pod
Drop critical-pod annotation(removed from 1.16+) in favor of priorityClassName
Pass all parameters as env in helm chart and example daemonset.yamls files for consistency

Version v0.11.0

Update CUDA base image version to 11.6.0
Add support for multi-arch images

Version v0.10.0

Update CUDA base images to 11.4.2
Ignore Xid=13 (Graphics Engine Exception) critical errors in device health-check
Ignore Xid=68 (Video processor exception) critical errors in device health-check
Build multi-arch container images for linux/amd64 and linux/arm64
Use Ubuntu 20.04 for Ubuntu-based container images
Remove Centos7 images

Version v0.9.0

Fix bug when using CPUManager and the device plugin MIG mode not set to "none"
Allow passing list of GPUs by device index instead of uuid
Move to urfave/cli to build the CLI
Support setting command line flags via environment variables

Version v0.8.2

Update all dockerhub references to nvcr.io

Version v0.8.1

Fix permission error when using NewDevice instead of NewDeviceLite when constructing MIG device map

Version v0.8.0

Raise an error if a device has migEnabled=true but has no MIG devices
Allow mig.strategy=single on nodes with non-MIG gpus

Version v0.7.3

Update vendoring to include bug fix for nvmlEventSetWait_v2

Version v0.7.2

Fix bug in dockfiles for ubi8 and centos using CMD not ENTRYPOINT

Version v0.7.1

Update all Dockerfiles to point to latest cuda-base on nvcr.io

Version v0.7.0

Promote v0.7.0-rc.8 to v0.7.0

Version v0.7.0-rc.8

Permit configuration of alternative container registry through environment variables.
Add an alternate set of gitlab-ci directives under .nvidia-ci.yml
Update all k8s dependencies to v1.19.1
Update vendoring for NVML Go bindings
Move restart loop to force recreate of plugins on SIGHUP

Version v0.7.0-rc.7

Fix bug which only allowed running the plugin on machines with CUDA 10.2+ installed

Version v0.7.0-rc.6

Add logic to skip / error out when unsupported MIG device encountered
Fix bug treating memory as multiple of 1000 instead of 1024
Switch to using CUDA base images
Add a set of standard tests to the .gitlab-ci.yml file

Version v0.7.0-rc.5

Add deviceListStrategyFlag to allow device list passing as volume mounts

Version v0.7.0-rc.4

Allow one to override selector.matchLabels in the helm chart
Allow one to override the udateStrategy in the helm chart

Version v0.7.0-rc.3

Fail the plugin if NVML cannot be loaded
Update logging to print to stderr on error
Add best effort removal of socket file before serving
Add logic to implement GetPreferredAllocation() call from kubelet

Version v0.7.0-rc.2

Add the ability to set 'resources' as part of a helm install
Add overrides for name and fullname in helm chart
Add ability to override image related parameters helm chart
Add conditional support for overriding secutiryContext in helm chart

Version v0.7.0-rc.1

Added migStrategy as a parameter to select the MIG strategy to the helm chart
Add support for MIG with different strategies {none, single, mixed}
Update vendored NVML bindings to latest (to include MIG APIs)
Add license in UBI image
Update UBI image with certification requirements

Version v0.6.0

Update CI, build system, and vendoring mechanism
Change versioning scheme to v0.x.x instead of v1.0.0-betax
Introduced helm charts as a mechanism to deploy the plugin

Version v0.5.0

Add a new plugin.yml variant that is compatible with the CPUManager
Change CMD in Dockerfile to ENTRYPOINT
Add flag to optionally return list of device nodes in Allocate() call
Refactor device plugin to eventually handle multiple resource types
Move plugin error retry to event loop so we can exit with a signal
Update all vendored dependencies to their latest versions
Fix bug that was inadvertently always disabling health checks
Update minimal driver version to 384.81

Version v0.4.0

Fixes a bug with a nil pointer dereference around getDevices:CPUAffinity

Version v0.3.0

Manifest is updated for Kubernetes 1.16+ (apps/v1)
Adds more logging information

Version v0.2.0

Adds the Topology field for Kubernetes 1.16+

Version v0.1.0

If gRPC throws an error, the device plugin no longer ends up in a non responsive state.

Version v0.0.0

Reversioned to SEMVER as device plugins aren't tied to a specific version of kubernetes anymore.

Version v1.11

No change.

Version v1.10

The device Plugin API is now v1beta1

Version v1.9

The device Plugin API changed and is no longer compatible with 1.8
Error messages were added

Issues and Contributing

Checkout the Contributing document!

You can report a bug by filing a new issue
You can contribute by opening a pull request

Versioning

Before v1.10 the versioning scheme of the device plugin had to match exactly the version of Kubernetes. After the promotion of device plugins to beta this condition was was no longer required. We quickly noticed that this versioning scheme was very confusing for users as they still expected to see a version of the device plugin for each version of Kubernetes.

This versioning scheme applies to the tags v1.8, v1.9, v1.10, v1.11, v1.12.

We have now changed the versioning to follow SEMVER. The first version following this scheme has been tagged v0.0.0.

Going forward, the major version of the device plugin will only change following a change in the device plugin API itself. For example, version v1beta1 of the device plugin API corresponds to version v0.x.x of the device plugin. If a new v2beta2 version of the device plugin API comes out, then the device plugin will increase its major version to 1.x.x.

As of now, the device plugin API for Kubernetes >= v1.10 is v1beta1. If you have a version of Kubernetes >= 1.10 you can deploy any device plugin version > v0.0.0.

Upgrading Kubernetes with the Device Plugin

Upgrading Kubernetes when you have a device plugin deployed doesn't require you to do any, particular changes to your workflow. The API is versioned and is pretty stable (though it is not guaranteed to be non breaking). Starting with Kubernetes version 1.10, you can use v0.3.0 of the device plugin to perform upgrades, and Kubernetes won't require you to deploy a different version of the device plugin. Once a node comes back online after the upgrade, you will see GPUs re-registering themselves automatically.

Upgrading the device plugin itself is a more complex task. It is recommended to drain GPU tasks as we cannot guarantee that GPU tasks will survive a rolling upgrade. However we make best efforts to preserve GPU tasks during an upgrade.

Name		Name	Last commit message	Last commit date
Latest commit History 891 Commits
.github		.github
api/config/v1		api/config/v1
cmd		cmd
deployments		deployments
docker		docker
internal		internal
vendor		vendor
.common-ci.yml		.common-ci.yml
.dockerignore		.dockerignore
.gitignore		.gitignore
.gitlab-ci.yml		.gitlab-ci.yml
.nvidia-ci.yml		.nvidia-ci.yml
CONTRIBUTING.md		CONTRIBUTING.md
LICENSE		LICENSE
Makefile		Makefile
README.md		README.md
RELEASE.md		RELEASE.md
config-manager		config-manager
coverage.out		coverage.out
go.mod		go.mod
go.sum		go.sum
nvidia-device-plugin.yml		nvidia-device-plugin.yml
pod1.yml		pod1.yml
versions.mk		versions.mk

License

nebuly-ai/k8s-device-plugin

Folders and files

Latest commit

History

Repository files navigation

NVIDIA device plugin for Kubernetes

Installation

Installation alongside the NVIDIA device plugin

Table of Contents

About

Prerequisites

Quick Start

Preparing your GPU Nodes

Example for debian-based systems with docker and containerd

Install the nvidia-container-toolkit

Configure docker

Configure containerd

Enabling GPU Support in Kubernetes

Running GPU Jobs

Configuring the NVIDIA device plugin binary

As command line flags or envvars

As a configuration file

Configuration Option Details

Shared Access to GPUs with CUDA Time-Slicing

Deployment via helm

Configuring the device plugin's helm chart

Passing configuration to the plugin via a ConfigMap.

Single Config File Example

Multiple Config File Example

Updating Per-Node Configuration With a Node Label

Setting other helm chart values

Deploying with gpu-feature-discovery for automatic node labels

Deploying via helm install with a direct URL to the helm package

Building and Running Locally

With Docker

Build

Run

Without Docker

Build

Run

Changelog

Version v0.14.0

Version v0.14.0-rc.3

Version v0.14.0-rc.2

Version v0.14.0-rc.1

Version v0.13.0

Version v0.13.0-rc.3

Version v0.13.0-rc.2

Version v0.13.0-rc.1

Version v0.12.3

Version v0.12.2

Version v0.12.1

Version v0.12.0

Version v0.12.0-rc.6

Version v0.12.0-rc.5

Version v0.12.0-rc.4

Version v0.12.0-rc.3

Version v0.12.0-rc.2

Version v0.12.0-rc.1

Version v0.11.0

Version v0.10.0

Version v0.9.0

Version v0.8.2

Version v0.8.1

Version v0.8.0

Version v0.7.3

Version v0.7.2

Version v0.7.1

Version v0.7.0

Version v0.7.0-rc.8

Version v0.7.0-rc.7

Version v0.7.0-rc.6

Version v0.7.0-rc.5

Version v0.7.0-rc.4

Version v0.7.0-rc.3

Version v0.7.0-rc.2

Version v0.7.0-rc.1

Version v0.6.0

Version v0.5.0

Example for debian-based systems with `docker` and `containerd`

Install the `nvidia-container-toolkit`

Configure `docker`

Configure `containerd`

Deployment via `helm`

Configuring the device plugin's `helm` chart

Passing configuration to the plugin via a `ConfigMap`.

Deploying via `helm install` with a direct URL to the `helm` package

Packages