Add Heltec new boards.

boards/heltec_mesh_node_t114.json

@@ -0,0 +1,53 @@
+{
+  "build": {
+    "arduino": {
+      "ldscript": "nrf52840_s140_v6.ld"
+    },
+    "core": "nRF5",
+    "cpu": "cortex-m4",
+    "extra_flags": "-DARDUINO_NRF52840_PCA10056 -DNRF52840_XXAA",
+    "f_cpu": "64000000L",
+    "hwids": [
+      ["0x239A", "0x4405"],
+      ["0x239A", "0x0029"],
+      ["0x239A", "0x002A"]
+    ],
+    "usb_product": "HT-n5262",
+    "mcu": "nrf52840",
+    "variant": "heltec_mesh_node_t114",
+    "variants_dir": "variants",
+    "bsp": {
+      "name": "adafruit"
+    },
+    "softdevice": {
+      "sd_flags": "-DS140",
+      "sd_name": "s140",
+      "sd_version": "6.1.1",
+      "sd_fwid": "0x00B6"
+    },
+    "bootloader": {
+      "settings_addr": "0xFF000"
+    }
+  },
+  "connectivity": ["bluetooth"],
+  "debug": {
+    "jlink_device": "nRF52840_xxAA",
+    "onboard_tools": ["jlink"],
+    "svd_path": "nrf52840.svd",
+    "openocd_target": "nrf52840-mdk-rs"
+  },
+  "frameworks": ["arduino"],
+  "name": "Heltec nrf (Adafruit BSP)",
+  "upload": {
+    "maximum_ram_size": 248832,
+    "maximum_size": 815104,
+    "speed": 115200,
+    "protocol": "nrfutil",
+    "protocols": ["jlink", "nrfjprog", "nrfutil", "stlink"],
+    "use_1200bps_touch": true,
+    "require_upload_port": true,
+    "wait_for_upload_port": true
+  },
+  "url": "FIXME",
+  "vendor": "Heltec"
+}

platformio.ini

@@ -35,6 +35,10 @@ default_envs = tbeam
 ;default_envs = radiomaster_900_bandit_nano
 ;default_envs = radiomaster_900_bandit_micro
 ;default_envs = heltec_capsule_sensor_v3
+;default_envs = heltec_vision_master_t190
+;default_envs = heltec_vision_master_e213
+;default_envs = heltec_vision_master_e290
+;default_envs = heltec_mesh_node_t114
 
 extra_configs =
   arch/*/*.ini

src/Power.cpp

@@ -233,11 +233,19 @@ class AnalogBatteryLevel : public HasBatteryLevel
             scaled = esp_adc_cal_raw_to_voltage(raw, adc_characs);
             scaled *= operativeAdcMultiplier;
 #else // block for all other platforms
+#ifdef ADC_CTRL              // enable adc voltage divider when we need to read
+        pinMode(ADC_CTRL, OUTPUT);
+        digitalWrite(ADC_CTRL, ADC_CTRL_ENABLED);
+        delay(10);
+#endif
             for (uint32_t i = 0; i < BATTERY_SENSE_SAMPLES; i++) {
                 raw += analogRead(BATTERY_PIN);
             }
             raw = raw / BATTERY_SENSE_SAMPLES;
             scaled = operativeAdcMultiplier * ((1000 * AREF_VOLTAGE) / pow(2, BATTERY_SENSE_RESOLUTION_BITS)) * raw;
+#ifdef ADC_CTRL // disable adc voltage divider when we need to read
+        digitalWrite(ADC_CTRL, !ADC_CTRL_ENABLED);
+#endif
 #endif
 
             if (!initial_read_done) {

src/graphics/EInkDisplay2.cpp

@@ -156,7 +156,7 @@ bool EInkDisplay::connect()
         }
     }
 
-#elif defined(HELTEC_WIRELESS_PAPER_V1_0) || defined(HELTEC_WIRELESS_PAPER)
+#elif defined(HELTEC_WIRELESS_PAPER_V1_0) || defined(HELTEC_WIRELESS_PAPER) || defined(HELTEC_VISION_MASTER_E213) || defined(HELTEC_VISION_MASTER_E290)
     {
         // Start HSPI
         hspi = new SPIClass(HSPI);

src/graphics/EInkDisplay2.h

@@ -5,11 +5,6 @@
 #include "GxEPD2_BW.h"
 #include <OLEDDisplay.h>
 
-#if defined(HELTEC_WIRELESS_PAPER_V1_0) || defined(HELTEC_WIRELESS_PAPER)
-// Re-enable SPI after deep sleep: rtc_gpio_hold_dis()
-#include "driver/rtc_io.h"
-#endif
-
 /**
  * An adapter class that allows using the GxEPD2 library as if it was an OLEDDisplay implementation.
  *
@@ -72,7 +67,7 @@ class EInkDisplay : public OLEDDisplay
     GxEPD2_BW<EINK_DISPLAY_MODEL, EINK_DISPLAY_MODEL::HEIGHT> *adafruitDisplay = NULL;
 
     // If display uses HSPI
-#if defined(HELTEC_WIRELESS_PAPER) || defined(HELTEC_WIRELESS_PAPER_V1_0)
+#if defined(HELTEC_WIRELESS_PAPER) || defined(HELTEC_WIRELESS_PAPER_V1_0) || defined(HELTEC_VISION_MASTER_E213) || defined(HELTEC_VISION_MASTER_E290)
     SPIClass *hspi = NULL;
 #endif
 

src/graphics/Screen.cpp

@@ -1485,13 +1485,23 @@ static void drawNodeInfo(OLEDDisplay *display, OLEDDisplayUiState *state, int16_
     screen->drawColumns(display, x, y, fields);
 }
 
+#if defined(ESP_PLATFORM) && defined(USE_ST7789)
+SPIClass SPI1(HSPI);
+#endif
+
 Screen::Screen(ScanI2C::DeviceAddress address, meshtastic_Config_DisplayConfig_OledType screenType, OLEDDISPLAY_GEOMETRY geometry)
     : concurrency::OSThread("Screen"), address_found(address), model(screenType), geometry(geometry), cmdQueue(32)
 {
     graphics::normalFrames = new FrameCallback[MAX_NUM_NODES + NUM_EXTRA_FRAMES];
 #if defined(USE_SH1106) || defined(USE_SH1107) || defined(USE_SH1107_128_64)
     dispdev = new SH1106Wire(address.address, -1, -1, geometry,
                              (address.port == ScanI2C::I2CPort::WIRE1) ? HW_I2C::I2C_TWO : HW_I2C::I2C_ONE);
+#elif defined(USE_ST7789)
+#ifdef ESP_PLATFORM
+	dispdev = new ST7789Spi(&SPI1, ST7789_RESET, ST7789_RS, ST7789_NSS,GEOMETRY_RAWMODE,TFT_WIDTH,TFT_HEIGHT,ST7789_SDA,ST7789_MISO,ST7789_SCK);
+#else
+	dispdev = new ST7789Spi(&SPI1, ST7789_RESET, ST7789_RS, ST7789_NSS,GEOMETRY_RAWMODE,TFT_WIDTH,TFT_HEIGHT);
+#endif
 #elif defined(USE_SSD1306)
     dispdev = new SSD1306Wire(address.address, -1, -1, geometry,
                               (address.port == ScanI2C::I2CPort::WIRE1) ? HW_I2C::I2C_TWO : HW_I2C::I2C_ONE);
@@ -1570,7 +1580,14 @@ void Screen::handleSetOn(bool on, FrameCallback einkScreensaver)
 #endif
 
             dispdev->displayOn();
-
+#ifdef USE_ST7789
+#ifdef ESP_PLATFORM
+            analogWrite(VTFT_LEDA,BRIGHTNESS_DEFAULT);
+#else
+            pinMode(VTFT_LEDA,OUTPUT);
+            digitalWrite(VTFT_LEDA,TFT_BACKLIGHT_ON);
+#endif
+#endif
             enabled = true;
             setInterval(0); // Draw ASAP
             runASAP = true;
@@ -1581,6 +1598,12 @@ void Screen::handleSetOn(bool on, FrameCallback einkScreensaver)
 #endif
             LOG_INFO("Turning off screen\n");
             dispdev->displayOff();
+
+#ifdef USE_ST7789
+            pinMode(VTFT_LEDA,OUTPUT);
+            digitalWrite(VTFT_LEDA,!TFT_BACKLIGHT_ON);
+#endif
+
 #ifdef T_WATCH_S3
             PMU->disablePowerOutput(XPOWERS_ALDO2);
 #endif
@@ -1595,7 +1618,7 @@ void Screen::setup()
     // We don't set useDisplay until setup() is called, because some boards have a declaration of this object but the device
     // is never found when probing i2c and therefore we don't call setup and never want to do (invalid) accesses to this device.
     useDisplay = true;
-
+    
 #ifdef AutoOLEDWire_h
     if (isAUTOOled)
         static_cast<AutoOLEDWire *>(dispdev)->setDetected(model);

src/graphics/Screen.h

@@ -45,6 +45,8 @@ class Screen
 #include <SH1106Wire.h>
 #elif defined(USE_SSD1306)
 #include <SSD1306Wire.h>
+#elif defined(USE_ST7789)
+#include <ST7789Spi.h>
 #else
 // the SH1106/SSD1306 variant is auto-detected
 #include <AutoOLEDWire.h>

src/main.cpp

@@ -275,6 +275,9 @@ void setup()
     digitalWrite(VEXT_ENABLE_V05, 1); // turn on the lora antenna boost
     digitalWrite(ST7735_BL_V05, 1);   // turn on display backligth
     LOG_DEBUG("HELTEC Detect Tracker V1.1\n");
+#elif defined(VEXT_ENABLE) && defined(VEXT_ON_VALUE)
+    pinMode(VEXT_ENABLE, OUTPUT);
+    digitalWrite(VEXT_ENABLE, VEXT_ON_VALUE); // turn on the display power
 #elif defined(VEXT_ENABLE)
     pinMode(VEXT_ENABLE, OUTPUT);
     digitalWrite(VEXT_ENABLE, 0); // turn on the display power
@@ -713,7 +716,7 @@ void setup()
 
 // Don't call screen setup until after nodedb is setup (because we need
 // the current region name)
-#if defined(ST7735_CS) || defined(USE_EINK) || defined(ILI9341_DRIVER) || defined(ST7789_CS) || defined(HX8357_CS)
+#if defined(ST7735_CS) || defined(USE_EINK) || defined(ILI9341_DRIVER) || defined(ST7789_CS) || defined(HX8357_CS) || defined(USE_ST7789)
     screen->setup();
 #elif defined(ARCH_PORTDUINO)
     if (screen_found.port != ScanI2C::I2CPort::NO_I2C || settingsMap[displayPanel]) {

src/mesh/NodeDB.cpp

@@ -268,7 +268,7 @@ void NodeDB::installDefaultConfig()
     // FIXME: Default to bluetooth capability of platform as default
     config.bluetooth.enabled = true;
     config.bluetooth.fixed_pin = defaultBLEPin;
-#if defined(ST7735_CS) || defined(USE_EINK) || defined(ILI9341_DRIVER) || defined(ST7789_CS) || defined(HX8357_CS)
+#if defined(ST7735_CS) || defined(USE_EINK) || defined(ILI9341_DRIVER) || defined(ST7789_CS) || defined(HX8357_CS) || defined(USE_ST7789)
     bool hasScreen = true;
 #elif ARCH_PORTDUINO
     bool hasScreen = false;

src/platform/esp32/architecture.h

@@ -151,6 +151,14 @@
 #define HW_VENDOR meshtastic_HardwareModel_RADIOMASTER_900_BANDIT_NANO
 #elif defined(HELTEC_CAPSULE_SENSOR_V3)
 #define HW_VENDOR meshtastic_HardwareModel_HELTEC_CAPSULE_SENSOR_V3
+#elif defined(HELTEC_VISION_MASTER_T190)
+#define HW_VENDOR meshtastic_HardwareModel_HELTEC_VISION_MASTER_T190
+#elif defined(HELTEC_VISION_MASTER_E213)
+#define HW_VENDOR meshtastic_HardwareModel_HELTEC_VISION_MASTER_E213
+#elif defined(HELTEC_VISION_MASTER_E290)
+#define HW_VENDOR meshtastic_HardwareModel_HELTEC_VISION_MASTER_E290
+#elif defined(HELTEC_MESH_NODE_T114)
+#define HW_VENDOR meshtastic_HardwareModel_HELTEC_MESH_NODE_T114
 #endif
 
 // -----------------------------------------------------------------------------

src/sleep.cpp

@@ -257,6 +257,8 @@ void doDeepSleep(uint32_t msecToWake, bool skipPreflight = false)
 #elif defined(VEXT_ENABLE_V05)
     digitalWrite(VEXT_ENABLE_V05, 0); // turn off the lora amplifier power
     digitalWrite(ST7735_BL_V05, 0);   // turn off the display power
+#elif defined(VEXT_ENABLE) && defined(VEXT_ON_VALUE)
+	digitalWrite(VEXT_ENABLE, !VEXT_ON_VALUE); // turn on the display power
 #elif defined(VEXT_ENABLE)
     digitalWrite(VEXT_ENABLE, 1); // turn off the display power
 #endif

variants/heltec_mesh_node_t114/platformio.ini

@@ -0,0 +1,15 @@
+; First prototype nrf52840/sx1262 device
+[env:heltec-mesh-node-t114]
+extends = nrf52840_base
+board = heltec_mesh_node_t114
+debug_tool = jlink
+
+# add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
+build_flags = ${nrf52840_base.build_flags} -Ivariants/heltec_mesh_node_t114
+        -L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
+
+build_src_filter = ${nrf52_base.build_src_filter} +<../variants/heltec_mesh_node_t114> 
+lib_deps = 
+  ${nrf52840_base.lib_deps}
+  lewisxhe/PCF8563_Library@^1.0.1
+  https://github.com/Bei-Ji-Quan/st7789#b8e7e076714b670764139289d3829b0beff67edb

variants/heltec_mesh_node_t114/variant.cpp

@@ -0,0 +1,44 @@
+/*
+  Copyright (c) 2014-2015 Arduino LLC.  All right reserved.
+  Copyright (c) 2016 Sandeep Mistry All right reserved.
+  Copyright (c) 2018, Adafruit Industries (adafruit.com)
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+  See the GNU Lesser General Public License for more details.
+
+  You should have received a copy of the GNU Lesser General Public
+  License along with this library; if not, write to the Free Software
+  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#include "variant.h"
+#include "nrf.h"
+#include "wiring_constants.h"
+#include "wiring_digital.h"
+
+const uint32_t g_ADigitalPinMap[] = {
+    // P0 - pins 0 and 1 are hardwired for xtal and should never be enabled
+    0xff, 0xff, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
+
+    // P1
+    32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
+
+void initVariant()
+{
+    // LED1 & LED2
+    pinMode(PIN_LED1, OUTPUT);
+    ledOff(PIN_LED1);
+
+    pinMode(PIN_LED2, OUTPUT);
+    ledOff(PIN_LED2);
+
+    pinMode(PIN_LED3, OUTPUT);
+    ledOff(PIN_LED3);
+}