HomeAssistant HACS custom RPI GPIOD integration

This HACS integration is used to address GPIO (especially and only tested for RaspberryPi) using libgpiod and python gpiod >=v2.02 since RPI.gpio is no longer supported. I created this for my own use, and to understand a custom integration, but since it is working on Raspberry pi feel free to use.

This work is copied over to the original HACS RPI_GPIO integration. You should most likely check the that integration instead of this one. I'm keeping this repository for my own fun and use for now.

This is working in my homeassistant environment, that's it. Shared for testing and usage at your own risk!

ha_gpiod is based on ha-rpi_gpio, which was already adapted for gpiod in ha-gpio and rewritten from scratch by me ..

Installation

Via HACS: add as custom repository from github using this github https://github.com/jdeneef/ha_gpiod/ (HACS => integrations => 3-dots menu => custom repositories, enter repository URL, select "Integrations" in Category drop-down, go back to hacs, install gpiod component, reboot, add config, reboot).
If you run into errors, ensure HACS is up-to-date, re-install HACS to update it if needed.

Usage

The gpiod platform will be initialized using the path to the gpio chip. When path is not in the config /dev/gpiochip[0-5] are tested for a gpiodevice having pinctrl, in sequence [0,4,1,2,3,5]. So with a raspberry pi you should be OK to leave the path empty.

Raspberry Pi	GPIO Device
RPi3, RPi4	/dev/gpiochip0
RPi5	/dev/gpiochip4

Sample config for the raspberry pi berryclip hat

See also configuraton-example.yaml; note that below config shows most options, and can't be used as is, since cover reuses switch and sensor ports.

# setup gpiod chip; mostly not required
gpiod:
  path: '/dev/gpiochip0'

# Example of switches (eg switched leds or buzzer) with some sample parameters
switch:
  - platform: gpiod
    switches:
      - name: "Led 1 red"
        port: 4
      - name: "Led 2 red"
        port: 17
        unique_id: "gpio_led_red_2"
      - name: "Led 3 yellow"
        port: 22
        active_low: true
      - name: "Led 6 green"
        port: 11
        bias: "AS_IS"
        drive: "PUSH_PULL"
      - name: "Fan"
        port: 8
        persistent: true

# Example of binary_sensor (eg push button) setup
binary_sensor:
  - platform: gpiod
    sensors:
    - name: "Button"
      port: 7

# Example of cover setup
cover:
  - platform: gpiod
    covers:
      - relay_port: 4
        name: Cover blue
        state_port: 7
        relay_time: 1200

Platform

Key	Required	Default	Type	Description
gpiod	only for path	-	-	gpiod platform config and initialization, only required when you need to specify a specific gpiodevice path (see path)
path	no	discovered	string	path to gpio device, if not set auto discovered

Binary Sensor

The gpiod binary sensor platform allows you to read sensor values of the GPIOs of your device. To ensure consistence over reboots the sensor status is read at startup and set accordingly.

Configuration options

Key	Required	Default	Type	Description
sensors	yes		list	List of sensor IO ports (Raspberry Pi BCM mode pin numbers)
name	yes		string	The name for the binary sensor entity
port	yes		integer	the GPIO port to be used
unique_id	no	generated	string	An ID that uniquely identifies the sensor. Set this to a unique value to allow customization through the UI, auto generated when not set manually in config
debounce	no	50	integer	The time in milliseconds for port debouncing
active_low or invert_logic	no	false	boolean	If true, input of gpio is inverted, active_low results in on; invert_logic kept for backwards compatibility
bias or pull_mode	no	PULL_UP	string	control bias setting of GPIO, used to define the electrical state of a GPIO line when not actively driven; PULL_UP set weak pull-up resistor on the line, ensuring that the line is pulled to a high level (3.3V or 5V) when not actively driven; PULL_DOWN sets weak pull-down resistor to pull to low level (0V), DISABLED remains floating, AS_IS not changed; pull_mode kept for backwards compatibility

Switch

The gpiod switch platform allows you to control the GPIOs of your device. To ensure consistence over restarts the persistent flag should be set.

Options

Key	Required	Default	Type	Description
switches	yes		list	List of switch IO ports (Raspberry Pi BCM mode pin numbers)
name	yes		string	The name for the switch entity
port	yes		integer	the GPIO port to be used
unique_id	no	generated	string	An ID that uniquely identifies the switch. Set this to a unique value to allow customization through the UI, auto generated when not set manually in config
active_low or invert_logic	no	false	boolean	If true, output of gpio is inverted, active_low switches on; invert_logic kept for backwards compatibility
bias or pull_mode	no	AS_IS	string	Type of internal pull resistor to use: PULL_UP - pull-up resistor, PULL_DOWN - pull-down resistor, AS-IS no change; pull_mode kept for backwards compatibility
drive	no	PUSH_PULL	string	control drive configuration of the GPIO, determines how the line behaves when it is set to output mode; PUSH_PULL, GPIO line can both source and sink current, can actively drive the line to both high and low states. OPEN-DRAIN, GPPIO can only sink current (drive the line to low) and is otherwise left floating, and OPEN-SOURCE the reverse.
persistent	no	false	boolean	If true, the switch state will be persistent in HA and will be restored if HA restart / crash.

Cover

The gpiod cover platform allows you to control GPIOs to open/close covers; note that I have only verified cover functionality simulating with switches and buttons, so logic could be off on some points .. Covers consist of a switch for triggering cover motor, and a state sensor for determining the state of the cover. This state is as for all sensors read at startup time, so should be consistent over reboots.

Options

Key	Required	Default	Type	Description
name	yes		string	The name for the cover entity
relay_port or relay_pin	yes		integer	Relay switch gpio switching cover motor; relay_pin kept for backwards compatibility
relay_time	no	200	integer	Time in milliseconds relay switch will be switched to open/close cover
relay_active_low or invert_relay	no	false	boolean	invert input for relay_port; invert_relay kept for backwards compatibility
relay_bias	no	AS_IS	string	Type of internal pull resistor to use: PULL_UP - pull-up resistor, PULL_DOWN - pull-down resistor
relay_drive	no	PUSH_PULL	string	set relay_pin drive_mode, options: OPEN_DRAIN, OPEN_SOURCE, PUSH_PULL
state_port or state_pin	yes		integer	State port for opened/closed status of cover; state_pin kept for backwards compatibility
state_bias or state_pull_mode	no	PULL_UP	string	Type of internal pull resistor to use: PULL_UP - pull-up resistor, PULL_DOWN - pull-down resistor; state_pull_mode kept for backwards compatibility
state_active_low or invert_state	no	false	boolean	invert output for state pin; invert_state kept for backwards compatibility
state_debounce	no	50	integer	debounce parameter for the cover state sensor
unique_id	no	generated	string	An ID that uniquely identifies the switch. Set this to a unique value to allow customization through the UI, auto generated when not set manually in config

Add Debug info and issue reporting

Before reporting issues please add this to your configuration.yaml logger section, check logs and report issue adding logging.

logger:
  default: info
  logs:
    custom_components.gpiod: debug