Skip to content

PulseAudio-compatible rump kernel translator for GNU Hurd

License

Notifications You must be signed in to change notification settings

dm0-/hurd-rump-audio

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

1 Commit
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Hurd rump audio translator

Enable audio on GNU Hurd with a rump kernel server and PulseAudio.

This project provides a translator to be run at /dev/audio which is partially compatible with the Solaris audio device. It is not a complete implementation, but it supports enough of the functionality for a PulseAudio sink. This allows any application that plays sounds through PulseAudio to output audio on a GNU Hurd system.

Installation

This project itself depends on Hurd libraries and the rump client library, and it is a dependency of the PulseAudio build. The order should go as follows:

  1. Build and install everything needed for a Hurd development environment
  2. Build and install the rump kernel's buildrump.sh and pci-userspace
  3. Build and install this
  4. Build and install PulseAudio with the Solaris module enabled

The first two steps can be done with the standard upstream build processes.

Building the translator

The Makefile here is very basic. It supports many of the usual variables for configuring the build. Just running make && sudo make install should be enough to handle most needs. It will install the translator at /hurd/audio and its ioctl definitions at /usr/include/sys/audio.h by default.

Building PulseAudio

PulseAudio versions older than 11.0 require a minor edit to compile, since the Solaris module was only expected to be built with Solaris system headers.

sed -i -e 's,<sys/conf.h>,<sys/poll.h>,' src/modules/module-solaris.c

After this edit, it should be able to be built and installed using the normal upstream procedure. Ensure the configure command does not use the option --disable-solaris so it can detect <sys/audio.h>. Alternatively, append the --enable-solaris option to the configure command to require it.

System configuration

With the translator and PulseAudio's Solaris module installed, the following component configurations should result in an audible Hurd system.

Hardware configuration

The rump kernel described here expects to drive an AC97 sound card. For use with QEMU, include the -soundhw ac97 option to emulate such a device.

Rump kernel configuration

The translator acts as a rump client that accesses /dev/audio in the rump server's VFS. The following command starts a server with enough modules to support this and drive AC97 sound cards.

rump_server -s -v \
    -lrumpvfs \
    -lrumpdev \
    -lrumpdev_audio \
    -lrumpdev_audio_ac97 \
    -lrumpdev_pci \
    -lrumpdev_pci_auich \
    unix:///run/rump.sock

Note the socket it creates at /run/rump.sock must be writable for the UID of the translator process, which should be 0 (root) if it was started from a translator record on the file system.

Translator configuration

The translator command only has a single option, the URL of the rump server's socket. It is equivalent to using the RUMP_SERVER environment variable, but the command-line option has higher precedence. Assuming the translator was installed as /hurd/audio, the following command will start it for the above server and write the translator record to run it automatically on future boots.

settrans -acfgp /dev/audio /hurd/audio --url=unix:///run/rump.sock

Make sure /dev/audio is writable for whatever users should have permission to play sounds. At this point *.au files should be playable (or recordable) by direct writes (or reads) to this device.

PulseAudio configuration

To account for the translator's incomplete compatibility with Solaris, a few settings in PulseAudio's configuration should be defined to avoid unsupported ioctl calls, etc. If using default.pa, make the following modifications.

  • Avoid suspending, so don't load module-suspend-on-idle
  • Since module-detect isn't needed, replace it with module-solaris
  • Set record=no on module-solaris to avoid using streams
  • Set channel_map=mono channels=1 format=ulaw rate=8000 on module-solaris to pick some known-supported playback parameters

Any applications that use PulseAudio should now be able to play sounds without modifying them. A user's PulseAudio server should start automatically when it is needed, e.g. by running paplay on a sound file.

Implementation details

The translator provides a device node supporting four important operations:

  • Writing data, i.e. playing audio out of speakers
  • Reading data, i.e. recording audio from a microphone
  • The AUDIO_GETINFO ioctl, for retrieving device information
  • The AUDIO_SETINFO ioctl, for changing device information

The installed header <sys/audio.h> is a modified version of NetBSD's header <sys/audioio.h> to be more compatible with Solaris. However, the changes required to build on Hurd make it incompatible with both NetBSD and Solaris.

The Solaris device node uses the old POSIX streams interface which is not implemented here, but PulseAudio's usage of the device is limited enough for it to bypass the streams ioctls with the aforementioned configuration changes.

The audio ioctl character is A on both Solaris and NetBSD, but this value is invalid on Hurd, so the installed audio.h uses s instead. Also, Hurd's ioctl definitions for structured parameters are normally defined by pairs of the member data type and the count of consecutive members of that type. The struct audio_info members are too many to fit into that encoding scheme, so the ioctl definitions in audio.h pretend all members are 64-bit integers, with enough of them to match the same structure size.

The Solaris data structure has an output_muted member used by PulseAudio, but NetBSD does not define it. It was appended to the structure in audio.h as a 64-bit integer (to keep things evenly divisble) for source compatibility, but the value is never actually used by the translator.

As a final note: This is just a silly toy program. If anyone really wants to have PulseAudio use a rump server, it would be better to write a new PulseAudio module that directly connects to it for platform independence and less IPC.

About

PulseAudio-compatible rump kernel translator for GNU Hurd

Topics

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published