Only for use with Linux & Android
* Use "ip" and "iw" instead of "ifconfig" and "iwconfig"
It's described further down, READ THE README!
* v5.3.4 is the stable branch, not this, but this does have
better range then branches below + more fixes from Realtek
[Device] Alfa Networks AWUS036ACH
[Chipset] 88XXau (rtl8812au)
[Branch] v5.6.4.1
[Distance] 10m free sight
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 11.6 MBytes 97.4 Mbits/sec 0 96.2 KBytes
[ 5] 1.00-2.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 2.00-3.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 3.00-4.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 4.00-5.00 sec 11.2 MBytes 93.8 Mbits/sec 0 100 KBytes
[ 5] 5.00-6.00 sec 11.4 MBytes 95.9 Mbits/sec 0 105 KBytes
[ 5] 6.00-7.00 sec 11.2 MBytes 93.8 Mbits/sec 0 105 KBytes
[ 5] 7.00-8.00 sec 11.3 MBytes 94.9 Mbits/sec 0 157 KBytes
[ 5] 8.00-9.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 9.00-10.00 sec 11.2 MBytes 94.3 Mbits/sec 0 157 KBytes
[ 5] 10.00-11.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 11.00-12.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 12.00-13.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 13.00-14.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 14.00-15.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 15.00-16.00 sec 10.9 MBytes 91.7 Mbits/sec 0 157 KBytes
[ 5] 16.00-17.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 17.00-18.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 18.00-19.00 sec 11.2 MBytes 94.4 Mbits/sec 0 157 KBytes
[ 5] 19.00-20.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 20.00-21.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 21.00-22.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
[ 5] 22.00-23.00 sec 11.2 MBytes 93.8 Mbits/sec 0 157 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-23.15 sec 260 MBytes 94.2 Mbits/sec 0 sender
[ 5] 0.00-23.15 sec 0.00 Bytes 0.00 bits/sec receiver
This driver can be installed using [DKMS]. This is a system which will automatically recompile and install a kernel module when a new kernel gets installed or updated. To make use of DKMS, install the dkms package, which on Debian (based) systems is done like this:
$ sudo apt-get install dkms
In order to install the driver open a terminal in the directory with the source code and execute the following command:
$ sudo ./dkms-install.sh
In order to remove the driver from your system open a terminal in the directory with the source code and execute the following command:
$ sudo ./dkms-remove.sh
For building & installing the driver with 'make' use
$ make && make install
Download
$ git clone -b v5.6.4.2 https://github.com/aircrack-ng/rtl8812au.git
cd rtl*
Package / Build dependencies (Kali)
$ sudo apt-get update
$ sudo apt-get install build-essential libelf-dev linux-headers-`uname -r`
$ sudo apt-get install raspberrypi-kernel-headers
Then run this step to change platform in Makefile, For RPI 1/2/3/ & 0/Zero:
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM_RPI = n/CONFIG_PLATFORM_ARM_RPI = y/g' Makefile
But for RPI 3B+ & 4B you will need to run those below which builds the ARM64 arch driver:
$ sed -i 's/CONFIG_PLATFORM_I386_PC = y/CONFIG_PLATFORM_I386_PC = n/g' Makefile
$ sed -i 's/CONFIG_PLATFORM_ARM64_RPI = n/CONFIG_PLATFORM_ARM64_RPI = y/g' Makefile
In addition, if you receive an error message about unrecognized command line option ‘-mgeneral-regs-only’ (i.e., Raspbian Buster), you will need to run the following commands:
$ sed -i 's/^dkms build/ARCH=arm dkms build/' dkms-install.sh
$ sed -i 's/^MAKE="/MAKE="ARCH=arm\ /' dkms.conf
For setting monitor mode
- Fix problematic interference in monitor mode.
$ airmon-ng check kill
You may also uncheck the box "Automatically connect to this network when it is avaiable" in nm-connection-editor. This only works if you have a saved wifi connection.
- Set interface down
$ sudo ip link set wlan0 down
- Set monitor mode
$ sudo iw dev wlan0 set type monitor
- Set interface up
$ sudo ip link set wlan0 up
For setting TX power
$ sudo iw wlan0 set txpower fixed 3000
options 88XXau rtw_led_ctrl=0value can be 0 or 1
$ echo "0" > /proc/net/rtl8812au/$(your interface name)/led_ctrlvalue can be 0 or 1
$ cat /proc/net/rtl8812au/$(your interface name)/led_ctrl0: doesn't switch, 1: switch from usb2.0 to usb 3.0 2: switch from usb3.0 to usb 2.0
$ rmmod 88XXau
$ modprobe 88XXau rtw_switch_usb_mode:int (0: no switch 1: switch from usb2 to usb3 2: switch from usb3 to usb2)Newer versions of NetworkManager switches to random MAC address. Some users would prefer to use a fixed address. Simply add these lines below
[device]
wifi.scan-rand-mac-address=no
at the end of file /etc/NetworkManager/NetworkManager.conf and restart NetworkManager with the command:
$ sudo service NetworkManager restart
Alfa Networks - https://www.alfa.com.tw/
Realtek. - https://www.realtek.com
aircrack-ng - https://www.aircrack-ng.org
astsam - https://github.com/astsam
evilphish - https://github.com/evilphish
fariouche - https://github.com/fariouche
CGarces - https://github.com/CGarces
ZerBea - https://github.com/ZerBea
lwfinger - https://github.com/lwfinger
Ulli-Kroll. - https://github.com/Ulli-Kroll