HyperHDR not able to find my Hyperserial WLED device

[wou5er]

As title sasys it all...

After pulling out the power supply now the how setup doens't work anymore... in the past i had simalar problems but after a reboot it when back online.

The problem is hyperHDR doenst find the ESP anymore... debian does.... but not hyperhdr

wan't in the past the correct path to led device was acm instead of AML?

debian does see the esp when checking lsusb command
running hyperhdr20 beta

i'm thinking of a defect esp...

When changing baudrate in wled it freezes and need to be rebooted, after reboot the setting went back before the freeze... and its impossible to change lower or higher...

Any advice or help would be apprecieated!

its gives this log

2024-11-17T17:31:51.014Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:310) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":104,"espHandshake":true,"hardwareLedCount":null,"maxRetry":0,"output":"ttyAML1","rate":2000000,"refreshTime":7,"smoothingRefreshTime":7,"type":"adalight","white_channel_calibration":false}]
2024-11-17T17:31:51.014Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 142.86 Hz
2024-11-17T17:31:51.014Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:396) Refresh rate = 142.86 Hz
2024-11-17T17:31:51.014Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:346) Device is not ready to start a timer
2024-11-17T17:31:51.014Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:406) Refresh interval updated to 7ms
2024-11-17T17:31:51.014Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:49) DeviceType : adalight
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) LedCount : 104
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) RefreshTime : 7
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:65) Device name : ttyAML1
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:66) Auto selection: 0
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Baud rate : 2000000
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) ESP handshake : ON
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Delayed open : 0
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) Retry limit : 0
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:79) Adalight driver with activated high speeed & data integration check AWA protocol
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 104 leds: Awa 0x00 0x67 0x32
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:220) Enable the device
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyAML1
2024-11-17T17:31:51.015Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:206) _serialPort.open(QIODevice::ReadWrite): ttyAML1, Baud rate [2000000]bps
2024-11-17T17:31:51.054Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:211) portName: ttyAML1
2024-11-17T17:31:51.054Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:212) systemLocation: /dev/ttyAML1
2024-11-17T17:31:51.054Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:213) description:
2024-11-17T17:31:51.054Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) manufacturer:
2024-11-17T17:31:51.054Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) productIdentifier: 0x0
2024-11-17T17:31:51.054Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) vendorIdentifier: 0x0
2024-11-17T17:31:51.054Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) serialNumber:
2024-11-17T17:31:52.356Z [LEDDEVICE0_ADALIGHT] Could not detect HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico device
2024-11-17T17:31:52.356Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:63) Switch on
2024-11-17T17:31:52.356Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:139) Power On
2024-11-17T17:31:52.356Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:340) Starting timer with interval = 7ms
2024-11-17T17:32:22.122Z [IMAGETOLED_MNG0] Total index number is: 53160 (memory: 53160). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:32:28.198Z [IMAGETOLED_MNG0] Total index number is: 53202 (memory: 53202). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:32:53.049Z [IMAGETOLED_MNG0] Total index number is: 53160 (memory: 53160). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:32:54.287Z [IMAGETOLED_MNG0] Total index number is: 53202 (memory: 53202). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:33:06.696Z [IMAGETOLED_MNG0] Total index number is: 53160 (memory: 53160). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:33:08.170Z [IMAGETOLED_MNG0] Total index number is: 53202 (memory: 53202). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:33:10.533Z [IMAGETOLED_MNG0] Total index number is: 53160 (memory: 53160). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:33:11.974Z [IMAGETOLED_MNG0] Total index number is: 53202 (memory: 53202). User sparse processing is: disabled, image size: 960 x 540, area number: 104
2024-11-17T17:33:13.666Z [PERFORMANCE] [USB: FPS = 29.97, decoding = 5ms, frames = 1799, invalid = 0, mode = direct], [INSTANCE0: FPS = 29.97, processed = 1798], [LED0: FPS = 142.86, send = 8572, processed = 8572, dropped = 0]
2024-11-17T17:33:47.937Z [WEBSOCKET] (HyperAPI.cpp:957) log streaming activated for client ::ffff:192.168.1.20
2024-11-17T17:34:13.658Z [PERFORMANCE] [USB: FPS = 29.97, decoding = 9ms, frames = 1798, invalid = 0, mode = direct], [INSTANCE0: FPS = 29.97, processed = 1798], [LED0: FPS = 142.86, send = 8571, processed = 8571, dropped = 0]

[awawa-dev]

Hi
Check dmesg logs because the discovery and assigning device to serial port is there.

[wou5er]

here you go

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.2.0-odroid-arm64 ([email protected]) (gcc-10 (De bian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue, 31 Jan 2023 07:28:15 +0000
[ 0.000000] Machine model: Hardkernel ODROID-N2
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'secm on@5300000': base 0x0000000005300000, size 32 MiB
[ 0.000000] Reserved memory: bypass linux,cma node, using cmdline CMA params instead
[ 0.000000] OF: reserved mem: node linux,cma compatible matching fail
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000ed7fffff ]
[ 0.000000] NUMA: NODE_DATA [mem 0xed01da80-0xed01ffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x00000000ed7fffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff]
[ 0.000000] node 0: [mem 0x0000000005000000-0x00000000052fffff]
[ 0.000000] node 0: [mem 0x0000000005300000-0x00000000ed7fffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000ed7fffff]
[ 0.000000] On node 0, zone DMA: 10240 pages in unavailable ranges
[ 0.000000] cma: Reserved 800 MiB at 0x00000000b7400000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 20 pages/cpu s44392 r8192 d29336 u81920
[ 0.000000] pcpu-alloc: s44392 r8192 d29336 u81920 alloc=204096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 957600
[ 0.000000] Policy zone: DMA
[ 0.000000] Kernel command line: quiet console=tty1 cma=800M clk_ignore_unuse d fsck.mode=force fsck.repair=yes net.ifnames=0 console=ttyS0,115200n8
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes , linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2957488K/3891200K available (14976K kernel code, 1776K rw data, 4908K rodata, 3328K init, 658K bss, 114512K reserved, 819200K cma-reserved )
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jif fies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns
[ 0.000202] Console: colour dummy device 80x25
[ 0.000213] printk: console [tty1] enabled
[ 0.000313] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=96000)
[ 0.000321] pid_max: default: 32768 minimum: 301
[ 0.000368] LSM: initializing lsm=capability,yama,integrity,selinux
[ 0.000392] Yama: disabled by default; enable with sysctl kernel.yama.
[ 0.000409] SELinux: Initializing.
[ 0.000503] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, line ar)
[ 0.000519] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.001995] cblist_init_generic: Setting adjustable number of callback queues .
[ 0.002015] cblist_init_generic: Setting shift to 3 and lim to 1.
[ 0.002067] cblist_init_generic: Setting shift to 3 and lim to 1.
[ 0.002195] rcu: Hierarchical SRCU implementation.
[ 0.002200] rcu: Max phase no-delay instances is 1000.
[ 0.004342] smp: Bringing up secondary CPUs ...
[ 0.004916] Detected VIPT I-cache on CPU1
[ 0.005034] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.006124] CPU features: detected: Spectre-v2
[ 0.006136] CPU features: detected: Spectre-v4
[ 0.006141] CPU features: detected: Spectre-BHB
[ 0.006146] CPU features: detected: ARM erratum 858921
[ 0.006152] Detected VIPT I-cache on CPU2
[ 0.006238] arch_timer: Enabling local workaround for ARM erratum 858921
[ 0.006253] arch_timer: CPU2: Trapping CNTVCT access
[ 0.006263] CPU2: Booted secondary processor 0x0000000100 [0x410fd092]
[ 0.006801] Detected VIPT I-cache on CPU3
[ 0.006860] arch_timer: Enabling local workaround for ARM erratum 858921
[ 0.006868] arch_timer: CPU3: Trapping CNTVCT access
[ 0.006874] CPU3: Booted secondary processor 0x0000000101 [0x410fd092]
[ 0.007395] Detected VIPT I-cache on CPU4
[ 0.007456] arch_timer: Enabling local workaround for ARM erratum 858921
[ 0.007464] arch_timer: CPU4: Trapping CNTVCT access
[ 0.007470] CPU4: Booted secondary processor 0x0000000102 [0x410fd092]
[ 0.007987] Detected VIPT I-cache on CPU5
[ 0.008051] arch_timer: Enabling local workaround for ARM erratum 858921
[ 0.008060] arch_timer: CPU5: Trapping CNTVCT access
[ 0.008066] CPU5: Booted secondary processor 0x0000000103 [0x410fd092]
[ 0.008124] smp: Brought up 1 node, 6 CPUs
[ 0.008144] SMP: Total of 6 processors activated.
[ 0.008149] CPU features: detected: 32-bit EL0 Support
[ 0.008151] CPU features: detected: 32-bit EL1 Support
[ 0.008155] CPU features: detected: CRC32 instructions
[ 0.008222] CPU: All CPU(s) started at EL2
[ 0.008240] alternatives: applying system-wide alternatives
[ 0.010075] devtmpfs: initialized
[ 0.016699] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
[ 0.016721] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 0.029401] pinctrl core: initialized pinctrl subsystem
[ 0.030241] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.031118] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 0.031441] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allo cations
[ 0.031716] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic al locations
[ 0.031748] audit: initializing netlink subsys (disabled)
[ 0.031849] audit: type=2000 audit(0.028:1): state=initialized audit_enabled= 0 res=1
[ 0.032816] thermal_sys: Registered thermal governor 'fair_share'
[ 0.032822] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.032825] thermal_sys: Registered thermal governor 'step_wise'
[ 0.032829] thermal_sys: Registered thermal governor 'user_space'
[ 0.032856] cpuidle: using governor menu
[ 0.032944] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.033033] ASID allocator initialised with 65536 entries
[ 0.033823] Serial: AMBA PL011 UART driver
[ 0.046416] platform ff900000.vpu: Fixing up cyclic dependency with ff600000. hdmi-tx
[ 0.052392] platform hdmi-connector: Fixing up cyclic dependency with ff60000 0.hdmi-tx
[ 0.053595] KASLR disabled due to lack of seed
[ 0.054123] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.054129] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page
[ 0.054135] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.054138] HugeTLB: 508 KiB vmemmap can be freed for a 32.0 MiB page
[ 0.054143] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.054146] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[ 0.054150] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.054153] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[ 0.054807] cryptd: max_cpu_qlen set to 1000
[ 0.119945] raid6: neonx8 gen() 2773 MB/s
[ 0.187996] raid6: neonx4 gen() 2983 MB/s
[ 0.256035] raid6: neonx2 gen() 2583 MB/s
[ 0.324073] raid6: neonx1 gen() 2013 MB/s
[ 0.392117] raid6: int64x8 gen() 1355 MB/s
[ 0.460156] raid6: int64x4 gen() 1439 MB/s
[ 0.528209] raid6: int64x2 gen() 1342 MB/s
[ 0.596241] raid6: int64x1 gen() 1112 MB/s
[ 0.596245] raid6: using algorithm neonx4 gen() 2983 MB/s
[ 0.664281] raid6: .... xor() 2323 MB/s, rmw enabled
[ 0.664285] raid6: using neon recovery algorithm
[ 0.665136] iommu: Default domain type: Translated
[ 0.665142] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.665318] SCSI subsystem initialized
[ 0.665427] usbcore: registered new interface driver usbfs
[ 0.665447] usbcore: registered new interface driver hub
[ 0.665467] usbcore: registered new device driver usb
[ 0.665711] pps_core: LinuxPPS API ver. 1 registered
[ 0.665715] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [email protected]
[ 0.665725] PTP clock support registered
[ 0.665833] EDAC MC: Ver: 3.0.0
[ 0.666985] vgaarb: loaded
[ 0.667182] clocksource: Switched to clocksource arch_sys_counter
[ 0.667318] VFS: Disk quotas dquot_6.6.0
[ 0.667341] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.671484] NET: Registered PF_INET protocol family
[ 0.671674] IP idents hash table entries: 65536 (order: 7, 524288 bytes, line ar)
[ 0.674583] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 3276 8 bytes, linear)
[ 0.674611] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.674622] TCP established hash table entries: 32768 (order: 6, 262144 bytes , linear)
[ 0.674766] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, line ar)
[ 0.675103] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.675233] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.675275] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.675429] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.675458] PCI: CLS 0 bytes, default 64
[ 0.675692] Trying to unpack rootfs image as initramfs...
[ 0.683986] kvm [1]: IPA Size Limit: 40 bits
[ 0.691312] kvm [1]: vgic interrupt IRQ9
[ 0.691412] kvm [1]: Hyp mode initialized successfully
[ 0.692460] Initialise system trusted keyrings
[ 0.692584] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[ 0.692646] zbud: loaded
[ 0.693101] JFS: nTxBlock = 8192, nTxLock = 65536
[ 0.695634] SGI XFS with ACLs, security attributes, realtime, quota, no debug enabled
[ 0.696059] ocfs2: Registered cluster interface o2cb
[ 0.696132] OCFS2 User DLM kernel interface loaded
[ 0.696849] gfs2: GFS2 installed
[ 0.725129] xor: measuring software checksum speed
[ 0.727513] 8regs : 4145 MB/sec
[ 0.729959] 32regs : 4031 MB/sec
[ 0.732651] arm64_neon : 3669 MB/sec
[ 0.732655] xor: using function: 8regs (4145 MB/sec)
[ 0.732664] Key type asymmetric registered
[ 0.732668] Asymmetric key parser 'x509' registered
[ 0.732712] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 45)
[ 0.732825] io scheduler mq-deadline registered
[ 0.732830] io scheduler kyber registered
[ 0.732856] io scheduler bfq registered
[ 0.733198] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.745934] soc soc0: Amlogic Meson G12B (S922X) Revision 29:a (40:2) Detecte d
[ 0.749708] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.751087] Serial: AMBA driver
[ 0.751425] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart
[ 0.751920] ffd24000.serial: ttyAML1 at MMIO 0xffd24000 (irq = 15, base_baud = 1500000) is a meson_uart
[ 0.755986] brd: module loaded
[ 0.758857] loop: module loaded
[ 0.760811] tun: Universal TUN/TAP device driver, 1.6
[ 0.761017] usbcore: registered new interface driver cdc_ether
[ 0.761042] usbcore: registered new interface driver cdc_subset
[ 0.761277] VFIO - User Level meta-driver version: 0.3
[ 0.762971] usbcore: registered new interface driver usb-storage
[ 0.764158] mousedev: PS/2 mouse device common for all mice
[ 0.764285] i2c_dev: i2c /dev entries driver
[ 0.769100] cpufreq: cpufreq_online: CPU2: Running at unlisted initial freque ncy: 999999 KHz, changing to: 1000000 KHz
[ 0.770395] sdhci: Secure Digital Host Controller Interface driver
[ 0.770406] sdhci: Copyright(c) Pierre Ossman
[ 0.770473] Synopsys Designware Multimedia Card Interface Driver
[ 0.770814] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.772414] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.772611] meson-sm: secure-monitor enabled
[ 0.772742] hid: raw HID events driver (C) Jiri Kosina
[ 0.773060] usbcore: registered new interface driver usbhid
[ 0.773065] usbhid: USB HID core driver
[ 0.774145] NET: Registered PF_INET6 protocol family
[ 0.774546] Segment Routing with IPv6
[ 0.774563] In-situ OAM (IOAM) with IPv6
[ 0.774588] NET: Registered PF_PACKET protocol family
[ 0.774593] NET: Registered PF_KEY protocol family
[ 0.774639] 8021q: 802.1Q VLAN Support v1.8
[ 0.774664] Key type dns_resolver registered
[ 0.777690] registered taskstats version 1
[ 0.777798] Loading compiled-in X.509 certificates
[ 0.777997] zswap: loaded using pool lzo/zbud
[ 0.781061] Key type .fscrypt registered
[ 0.781070] Key type fscrypt-provisioning registered
[ 0.781418] Btrfs loaded, crc32c=crc32c-generic, zoned=yes, fsverity=no
[ 0.793311] meson-gx-mmc ffe05000.sd: Got CD GPIO
[ 0.798333] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[ 0.798351] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[ 0.801261] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator
[ 0.801368] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator
[ 0.802077] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[ 0.804355] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 0.804390] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus nu mber 1
[ 0.804488] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010
[ 0.804528] xhci-hcd xhci-hcd.0.auto: irq 21, io mem 0xff500000
[ 0.804654] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 0.804663] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus nu mber 2
[ 0.804672] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 0.804769] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 6.02
[ 0.804776] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.804781] usb usb1: Product: xHCI Host Controller
[ 0.804784] usb usb1: Manufacturer: Linux 6.2.0-odroid-arm64 xhci-hcd
[ 0.804788] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 0.805114] hub 1-0:1.0: USB hub found
[ 0.805137] hub 1-0:1.0: 2 ports detected
[ 0.805388] usb usb2: We don't know the algorithms for LPM for this host, dis abling LPM.
[ 0.805442] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bc dDevice= 6.02
[ 0.805448] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 0.805453] usb usb2: Product: xHCI Host Controller
[ 0.805457] usb usb2: Manufacturer: Linux 6.2.0-odroid-arm64 xhci-hcd
[ 0.805461] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 0.805710] hub 2-0:1.0: USB hub found
[ 0.805730] hub 2-0:1.0: 1 port detected
[ 0.806125] dwc3-meson-g12a ffe09000.usb: switching to Device Mode
[ 0.806956] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[ 0.807687] clk: Not disabling unused clocks
[ 0.819427] genirq: Setting trigger mode 3 for irq 24 failed (meson_gpio_irq_ set_type+0x0/0x60)
[ 0.903279] mmc0: new HS200 MMC card at address 0001
[ 0.903720] mmcblk0: mmc0:0001 BJTD4R 29.1 GiB
[ 0.904827] mmcblk0: p1 p2 p3 < p5 >
[ 0.905312] mmcblk0boot0: mmc0:0001 BJTD4R 4.00 MiB
[ 0.905974] mmcblk0boot1: mmc0:0001 BJTD4R 4.00 MiB
[ 0.906474] mmcblk0rpmb: mmc0:0001 BJTD4R 4.00 MiB, chardev (242:0)
[ 0.909528] Freeing initrd memory: 9368K
[ 0.922559] Freeing unused kernel memory: 3328K
[ 0.967518] Run /init as init process
[ 0.967528] with arguments:
[ 0.967531] /init
[ 0.967534] with environment:
[ 0.967536] HOME=/
[ 0.967537] TERM=linux
[ 1.095216] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 1.142800] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[ 1.142821] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[ 1.143042] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[ 1.145229] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[ 1.145246] meson8b-dwmac ff3f0000.ethernet: DWMAC1000
[ 1.145250] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register suppo rted
[ 1.145253] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine suppo rted
[ 1.145255] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[ 1.145258] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[ 1.145260] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[ 1.145312] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[ 1.145316] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[ 1.145318] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watc hdog Timer
[ 1.145322] meson8b-dwmac ff3f0000.ethernet: device MAC address 00:1e:06:42:4 4:b6
[ 1.161233] rtc-pcf8563 0-0051: registered as rtc0
[ 1.162445] rtc-pcf8563 0-0051: setting system clock to 2024-11-17T16:22:08 U TC (1731860528)
[ 1.245518] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcd Device=93.04
[ 1.245531] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.245534] usb 1-1: Product: USB2.1 Hub
[ 1.245537] usb 1-1: Manufacturer: GenesysLogic
[ 1.284917] hub 1-1:1.0: USB hub found
[ 1.285149] hub 1-1:1.0: 4 ports detected
[ 1.371299] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 1.393758] usb 2-1: New USB device found, idVendor=05e3, idProduct=0620, bcd Device=93.04
[ 1.393764] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.393768] usb 2-1: Product: USB3.1 Hub
[ 1.393771] usb 2-1: Manufacturer: GenesysLogic
[ 1.412878] hub 2-1:1.0: USB hub found
[ 1.413159] hub 2-1:1.0: 4 ports detected
[ 1.445229] PM: Image not found (code -22)
[ 1.937751] EXT4-fs (mmcblk0p2): mounted filesystem 4d5a219f-f8ab-4770-ad3a-f a45dfd7b4f1 with ordered data mode. Quota mode: none.
[ 2.107926] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +G NUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 defa ult-hierarchy=unified)
[ 2.108165] systemd[1]: Detected architecture arm64.
[ 2.108637] systemd[1]: Set hostname to .
[ 2.300570] systemd[1]: Queued start job for default target Graphical Interfa ce.
[ 3.431268] usb 2-1.3: new SuperSpeed USB device number 3 using xhci-hcd
[ 3.451594] usb 2-1.3: LPM exit latency is zeroed, disabling LPM.
[ 3.454073] usb 2-1.3: config 1 has an invalid interface number: 7 but max is 4
[ 3.454079] usb 2-1.3: config 1 has no interface number 4
[ 3.454089] usb 2-1.3: Int endpoint with wBytesPerInterval of 1024 in config 1 interface 7 altsetting 0 ep 135: setting to 512
[ 3.454592] usb 2-1.3: New USB device found, idVendor=32ed, idProduct=3200, b cdDevice= 1.00
[ 3.454599] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber =3
[ 3.454604] usb 2-1.3: Product: ezcap Game Link RAW
[ 3.454607] usb 2-1.3: Manufacturer: ezcap
[ 3.454611] usb 2-1.3: SerialNumber: 00000001
[ 3.527431] hid-generic 0003:32ED:3200.0001: hiddev96,hidraw0: USB HID v1.11 Device [ezcap ezcap Game Link RAW] on usb-xhci-hcd.0.auto-1.3/input7
[ 5.475172] random: crng init done
[ 5.499940] systemd[1]: Created slice system-getty.slice.
[ 5.500481] systemd[1]: Created slice system-hyperhdr.slice.
[ 5.500857] systemd[1]: Created slice system-modprobe.slice.
[ 5.501262] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ 5.501598] systemd[1]: Created slice User and Session Slice.
[ 5.501728] systemd[1]: Started Dispatch Password Requests to Console Directo ry Watch.
[ 5.501815] systemd[1]: Started Forward Password Requests to Wall Directory W atch.
[ 5.502119] systemd[1]: Set up automount Arbitrary Executable File Formats Fi le System Automount Point.
[ 5.502192] systemd[1]: Reached target Local Encrypted Volumes.
[ 5.502250] systemd[1]: Reached target Paths.
[ 5.502282] systemd[1]: Reached target Remote File Systems.
[ 5.502307] systemd[1]: Reached target Slices.
[ 5.502571] systemd[1]: Listening on Syslog Socket.
[ 5.502754] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 5.502857] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 5.503118] systemd[1]: Listening on Journal Audit Socket.
[ 5.503303] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.503500] systemd[1]: Listening on Journal Socket.
[ 5.504046] systemd[1]: Listening on udev Control Socket.
[ 5.504189] systemd[1]: Listening on udev Kernel Socket.
[ 5.505675] systemd[1]: Mounting Huge Pages File System...
[ 5.507335] systemd[1]: Mounting POSIX Message Queue File System...
[ 5.509089] systemd[1]: Mounting Kernel Debug File System...
[ 5.509352] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 5.511359] systemd[1]: Starting Set the console keyboard layout...
[ 5.513449] systemd[1]: Starting Create list of static device nodes for the c urrent kernel...
[ 5.515557] systemd[1]: Starting Load Kernel Module configfs...
[ 5.517603] systemd[1]: Starting Load Kernel Module drm...
[ 5.519769] systemd[1]: Starting Load Kernel Module fuse...
[ 5.520784] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 5.520921] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 5.524212] systemd[1]: Starting Journal Service...
[ 5.528053] systemd[1]: Starting Load Kernel Modules...
[ 5.530199] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 5.532577] systemd[1]: Starting Coldplug All udev Devices...
[ 5.535262] fuse: init (API version 7.38)
[ 5.536814] systemd[1]: Mounted Huge Pages File System.
[ 5.537232] systemd[1]: Mounted POSIX Message Queue File System.
[ 5.537509] systemd[1]: Mounted Kernel Debug File System.
[ 5.538557] systemd[1]: Finished Create list of static device nodes for the c urrent kernel.
[ 5.539702] systemd[1]: [email protected]: Succeeded.
[ 5.540438] systemd[1]: Finished Load Kernel Module configfs.
[ 5.541167] systemd[1]: [email protected]: Succeeded.
[ 5.541747] systemd[1]: Finished Load Kernel Module fuse.
[ 5.544345] systemd[1]: Mounting FUSE Control File System...
[ 5.546568] systemd[1]: Mounting Kernel Configuration File System...
[ 5.547845] systemd[1]: [email protected]: Succeeded.
[ 5.548575] systemd[1]: Finished Load Kernel Module drm.
[ 5.551611] systemd[1]: Finished Load Kernel Modules.
[ 5.552088] systemd[1]: Mounted FUSE Control File System.
[ 5.552379] systemd[1]: Mounted Kernel Configuration File System.
[ 5.554454] systemd[1]: Starting Apply Kernel Variables...
[ 5.555318] EXT4-fs (mmcblk0p2): re-mounted 4d5a219f-f8ab-4770-ad3a-fa45dfd7b 4f1. Quota mode: none.
[ 5.557958] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 5.559547] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 5.559654] systemd[1]: Condition check resulted in Platform Persistent Stora ge Archival being skipped.
[ 5.561515] systemd[1]: Starting Load/Save Random Seed...
[ 5.563750] systemd[1]: Starting Create System Users...
[ 5.571603] systemd[1]: Finished Apply Kernel Variables.
[ 5.592301] systemd[1]: Finished Load/Save Random Seed.
[ 5.592674] systemd[1]: Condition check resulted in First Boot Complete being skipped.
[ 5.599708] systemd[1]: Finished Create System Users.
[ 5.601630] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 5.615218] systemd[1]: Started Journal Service.
[ 5.627808] systemd-journald[999]: Received client request to flush runtime j ournal.
[ 5.634390] systemd-journald[999]: File /var/log/journal/b5eabce7a5074496b215 c6818336b600/system.journal corrupted or uncleanly shut down, renaming and repla cing.
[ 5.803223] usb 1-1.4: new full-speed USB device number 3 using xhci-hcd
[ 5.856589] gpio-fan gpio-fan: GPIO fan initialized
[ 5.905141] Registered IR keymap rc-odroid
[ 5.918810] mc: Linux media interface: v0.10
[ 5.918851] IR NEC protocol handler initialized
[ 5.927159] meson-drm ff900000.vpu: Queued 1 outputs on vpu
[ 5.948006] rc rc0: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.i r/rc/rc0
[ 5.950745] rc rc0: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[ 5.950946] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir /rc/rc0/input0
[ 5.953550] meson-drm ff900000.vpu: CVBS Output connector not available
[ 5.953711] videodev: Linux video capture interface: v2.00
[ 5.966286] meson-ir ff808000.ir: receiver initialized
[ 5.983257] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01 a with HDCP (meson_dw_hdmi_phy)
[ 5.987268] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[ 5.995332] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bu s driver
[ 5.995735] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi _ops [meson_dw_hdmi])
[ 6.003071] panfrost ffe40000.gpu: clock rate = 24000000
[ 6.003137] panfrost ffe40000.gpu: error -ENODEV: _opp_set_regulators: no reg ulator (mali) found
[ 6.017093] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 0
[ 6.018381] panfrost ffe40000.gpu: mali-g52 id 0x7212 major 0x0 minor 0x0 sta tus 0x0
[ 6.018400] panfrost ffe40000.gpu: features: 00000000,00000cf7, issues: 00000 000,00000400
[ 6.018406] panfrost ffe40000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7
[ 6.018412] panfrost ffe40000.gpu: shader_present=0x3 l2_present=0x1
[ 6.022348] [drm] Initialized panfrost 1.2.0 20180908 for ffe40000.gpu on min or 1
[ 6.082754] uvcvideo 2-1.3:1.1: Unknown video format e436eb7e-524f-11ce-9f53- 0020af0ba770
[ 6.082786] usb 2-1.3: Found UVC 1.10 device ezcap Game Link RAW (32ed:3200)
[ 6.092485] input: ezcap Game Link RAW: ezcap Game as /devices/platform/soc/f fe09000.usb/ff500000.usb/xhci-hcd.0.auto/usb2/2-1/2-1.3/2-1.3:1.0/input/input1
[ 6.092703] usbcore: registered new interface driver uvcvideo
[ 6.133213] usbcore: registered new interface driver snd-usb-audio
[ 6.166707] Adding 998396k swap on /dev/mmcblk0p5. Priority:-2 extents:1 acr oss:998396k SSFS
[ 6.196074] Console: switching to colour frame buffer device 128x48
[ 6.216337] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device
[ 6.551111] ext2 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
[ 6.628245] meson8b-dwmac ff3f0000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 6.803302] meson8b-dwmac ff3f0000.ethernet eth0: PHY [mdio_mux-0.0:00] drive r [RTL8211F Gigabit Ethernet] (irq=POLL)
[ 6.811205] meson8b-dwmac ff3f0000.ethernet eth0: No Safety Features support found
[ 6.811230] meson8b-dwmac ff3f0000.ethernet eth0: PTP not supported by HW
[ 6.811457] meson8b-dwmac ff3f0000.ethernet eth0: configuring for phy/rgmii l ink mode
[ 10.945931] meson8b-dwmac ff3f0000.ethernet eth0: Link is Up - 1Gbps/Full - f low control rx/tx
[ 10.945968] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.083209] usb 1-1.4: new high-speed USB device number 4 using xhci-hcd
[ 12.207463] usb 1-1.4: New USB device found, idVendor=1a40, idProduct=0101, b cdDevice= 1.11
[ 12.207497] usb 1-1.4: New USB device strings: Mfr=0, Product=1, SerialNumber =0
[ 12.207503] usb 1-1.4: Product: USB 2.0 Hub
[ 12.260982] hub 1-1.4:1.0: USB hub found
[ 12.261046] hub 1-1.4:1.0: 4 ports detected
[ 12.667190] usb 1-1.4.4: new full-speed USB device number 5 using xhci-hcd
[ 12.888371] usb 1-1.4.4: New USB device found, idVendor=1a86, idProduct=55d4, bcdDevice= 4.43
[ 12.888389] usb 1-1.4.4: New USB device strings: Mfr=0, Product=2, SerialNumb er=3
[ 12.888393] usb 1-1.4.4: Product: USB Single Serial
[ 12.888396] usb 1-1.4.4: SerialNumber: 5299007073
[ 12.941095] cdc_acm 1-1.4.4:1.0: ttyACM0: USB ACM device
[ 12.941146] usbcore: registered new interface driver cdc_acm
[ 12.941149] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters
[ 235.045409] usb 1-1.4: USB disconnect, device number 4
[ 235.045446] usb 1-1.4.4: USB disconnect, device number 5
[ 235.353357] usb 1-1.4: new full-speed USB device number 6 using xhci-hcd
[ 235.457365] usb 1-1.4: device descriptor read/64, error -32
[ 235.669431] usb 1-1.4: device descriptor read/64, error -32
[ 235.881381] usb 1-1.4: new full-speed USB device number 7 using xhci-hcd
[ 235.985402] usb 1-1.4: device descriptor read/64, error -32
[ 236.197394] usb 1-1.4: device descriptor read/64, error -32
[ 236.305608] usb 1-1-port4: attempt power cycle
[ 236.957312] usb 1-1.4: new full-speed USB device number 8 using xhci-hcd
[ 236.957403] usb 1-1.4: Device not responding to setup address.
[ 237.165432] usb 1-1.4: Device not responding to setup address.
[ 237.373334] usb 1-1.4: device not accepting address 8, error -71
[ 238.421345] usb 1-1.4: new full-speed USB device number 9 using xhci-hcd
[ 238.421473] usb 1-1.4: Device not responding to setup address.
[ 238.629332] usb 1-1.4: Device not responding to setup address.
[ 238.837307] usb 1-1.4: device not accepting address 9, error -71
[ 238.837771] usb 1-1-port4: unable to enumerate USB device
[ 505.588746] uvcvideo 2-1.3:1.1: Non-zero status (-71) in video completion han dler.
[ 525.019406] uvcvideo 2-1.3:1.1: Failed to resubmit video URB (-1).
[ 525.019539] uvcvideo 2-1.3:1.1: Failed to resubmit video URB (-1).
[ 525.019604] uvcvideo 2-1.3:1.1: Failed to resubmit video URB (-1).
[ 551.173528] uvcvideo 2-1.3:1.1: Non-zero status (-71) in video completion han dler.
[ 2772.305211] rc rc0: two consecutive events of type space

[awawa-dev]

I see the correct device there:
cdc_acm 1-1.4.4:1.0: ttyACM0: USB ACM device
Later something strange is happening to the USB HUB/PORT? but I dont know if its a critical error.

[wou5er]

ttyACM0 aint showing in hyperHDR

i got those other errors..

[ 235.353357] usb 1-1.4: new full-speed USB device number 6 using xhci-hcd
[ 235.457365] usb 1-1.4: device descriptor read/64, error -32
[ 235.669431] usb 1-1.4: device descriptor read/64, error -32
[ 235.881381] usb 1-1.4: new full-speed USB device number 7 using xhci-hcd
[ 235.985402] usb 1-1.4: device descriptor read/64, error -32
[ 236.197394] usb 1-1.4: device descriptor read/64, error -32
[ 236.305608] usb 1-1-port4: attempt power cycle
[ 236.957312] usb 1-1.4: new full-speed USB device number 8 using xhci-hcd
[ 236.957403] usb 1-1.4: Device not responding to setup address.
[ 237.165432] usb 1-1.4: Device not responding to setup address.
[ 237.373334] usb 1-1.4: device not accepting address 8, error -71
[ 238.421345] usb 1-1.4: new full-speed USB device number 9 using xhci-hcd
[ 238.421473] usb 1-1.4: Device not responding to setup address.
[ 238.629332] usb 1-1.4: Device not responding to setup address.
[ 238.837307] usb 1-1.4: device not accepting address 9, error -71
[ 238.837771] usb 1-1-port4: unable to enumerate USB device
[ 505.588746] uvcvideo 2-1.3:1.1: Non-zero status (-71) in video completion han dler.
[ 525.019406] uvcvideo 2-1.3:1.1: Failed to resubmit video URB (-1).
[ 525.019539] uvcvideo 2-1.3:1.1: Failed to resubmit video URB (-1).
[ 525.019604] uvcvideo 2-1.3:1.1: Failed to resubmit video URB (-1).

But i don't know what could be the problem

maby try to connect my capture device on that usb hub ... that one is powering the esp on wich isn't recognized..

[awawa-dev]

yes, disconnect the hub and connect ESP directly for testing

[wou5er]

chatgpt gives following asnwers about the errors

Key Messages in the Log:
Device Descriptor Errors (error -32):

These errors indicate the USB device failed during the initial communication attempts to provide its descriptor information to the host. Common causes include faulty cables, insufficient power, or device malfunction.
Power Cycling Attempt:

The system tries to reset the device (attempt power cycle) to recover, but it fails repeatedly.
Device Not Responding and Address Errors (error -71):

Error -71 suggests a protocol issue during USB communication. This often arises from hardware faults, incompatible devices, or issues with the USB controller.
UVC Video Errors (Non-zero status, Failed to resubmit video URB):

These errors are related to USB Video Class (UVC) devices, such as webcams, failing to process video data properly. This may stem from an unstable connection, device driver issues, or corrupted firmware.

[wou5er]

weird its working again without the hub and both the capture card and esp on odroid n2 directly
could it be odroid doesn't need external powerd usb hub?

[awawa-dev]

Ignore UVC errors for now if it's working, some grabbers under Linux have them naturally. Sometimes it's faulty cable also, sometime insufficient power supply. RPi power supply is very limited compared to many other SoC like N100: check the documention about it: https://github.com/raspberrypi/documentation/blob/develop/documentation/asciidoc/computers/raspberry-pi/power-supplies.adoc#typical-power-requirements

[wou5er]

well keep an eye on it any way thanks for troubleshooting again!

[wou5er]

i want to order a new esp32 because my setup makes it easier

wich one should you recommend of these 2?

CH9102X wich is micro usb
or
CP2102 TYPE C

i prefer type c cause its more durable.

https://nl.aliexpress.com/item/1005005527852473.html?spm=a2g0o.productlist.main.1.31e63e42Y0ewMt&algo_pvid=b5df6004-80e9-4c63-9b4e-510dc52c1ea3&algo_exp_id=b5df6004-80e9-4c63-9b4e-510dc52c1ea3-0&pdp_npi=4%40dis%21EUR%216.39%216.39%21%21%2147.62%2147.62%21%4021038e1e17318706804237576edfcc%2112000038317586803%21sea%21NL%21143916322%21X&curPageLogUid=ycxqUhjrHcWR&utparam-url=scene%3Asearch%7Cquery_from%3A

[awawa-dev]

In reality, the USB-C port is quite delicate and very difficult to re-solder properly. The ESP32-S2 mini has USB-C, but it is not officially supported by WLED and boards quality may vary. CP2102 is only 1Mb, CP2102N is ~4Mb I think. What will come from China? Nobody knows ;-)

[wou5er]

micro usb it is orderd the same board ... again wich was just fine.. i'm not gonna update everything with the newest hardware until i got another new tv... and i don't expect that will hapen fast.

i'm still running older ws2801 leds for at least 7 years now and i'm stil very happy with it