Sonoff-Tasmota v6.3.0
Migration Information
See wiki migration path for instructions how to migrate to a major version. Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14
- Migrate to Sonoff-Tasmota 6.x
Release notes
Change in default initial configuration tool
Firmware binary sonoff-classic.bin supports WifiManager, Wps and SmartConfig for initial configuration. The default tool is Wps.
To save memory space all other binaries support WifiManager only.
See _changelog.ino how to enable them again.
- Define WIFI_CONFIG_TOOL now contains the default behaviour once a SSID has been configured.
- If no SSID is configured making a wifi connection impossible the new define WIFI_CONFIG_NO_SSID will be used.
- While define WIFI_CONFIG_NO_SSID is set to WIFI_WPSCONFIG in my_user_config.h the compiler will check for define USE_WPS and if not enabled WIFI_CONFIG_NO_SSID will default to WIFI_MANAGER using the webserver. If define USE_WEBSERVER is also not enabled WIFI_CONFIG_NO_SSID will default to WIFI_SMARTCONFIG. If define USE_SMARTCONFIG is also not enabled WIFI_CONFIG_NO_SSID will default to a new option WIFI_SERIAL allowing to enter wifi parameters to serial which is always possible.
Supported Modules
The following hardware modules are supported.
| Module | Description |
|---|---|
| 01 Sonoff Basic | Sonoff Basic Wifi Smart Switch |
| 02 Sonoff RF | Sonoff RF Wifi Smart Switch with RF (434MHz) receiver |
| 03 Sonoff SV | Sonoff SV Safe Voltage Wifi Smart Switch |
| 04 Sonoff TH | Sonoff TH10/TH16 Wifi Smart Switch with Sensor connection |
| 05 Sonoff Dual | Sonoff Dual Wifi Smart Switch |
| 06 Sonoff Pow | Sonoff Pow Wifi Smart Switch with Energy Monitoring |
| 07 Sonoff 4CH | Sonoff 4CH 4-gang Wifi Smart Switch |
| 08 Sonoff S2X | Sonoff S20/S26 Wifi Smart Socket |
| 09 Slampher | Sonoff Slampher Wifi Smart Light Bulb Socket with RF (434MHz) receiver |
| 10 Sonoff Touch | Sonoff Touch Wifi Light Switch |
| 11 Sonoff LED | Sonoff Led Wifi Led Pack (Retired) |
| 12 1 Channel | 1 Channel Inching/Self Locking Wifi Switch 5V/12V |
| 13 4 Channel | 4 Channel Inching/Self Locking Wifi Switch (Retired) |
| 14 Motor C/AC | Motor Clockwise/Antoclockwise Wifi Switch (Retired) |
| 15 ElectroDragon | Electrodragon Wifi IoT Board |
| 16 EXS Relay(s) | Electronic Experience Store 1 or 2-gang Wifi Module |
| 17 WiOn | WiOn Wifi Smart Socket |
| 18 Generic | Any ESP8266/ESP8285 device like WeMos and NodeMCU |
| 19 Sonoff Dev | Sonoff Dev Wifi Development Board |
| 20 H801 | H801 Wifi RGBWW Led Controller |
| 21 Sonoff SC | Sonoff SC Wifi Environmental Monitor |
| 22 Sonoff BN-SZ | Sonoff BN-SZ01 Wifi Ceiling Led (Retired) |
| 23 Sonoff 4CH Pro | Sonoff 4CH Pro 4-gang Wifi Smart Switch |
| 24 Huafan SS | HuaFan Wifi Smart Socket |
| 25 Sonoff Bridge | Sonoff RF (434MHz) transceive to Wifi Bridge |
| 26 Sonoff B1 | Sonoff B1 Wifi RGBWW Led Bulb |
| 27 AiLight | Ai-Thinker RGBW Led Bulb |
| 28 Sonoff T1 1CH | Sonoff T1 1-gang Wifi Light Switch |
| 29 Sonoff T1 2CH | Sonoff T1 2-gang Wifi Light Switch |
| 30 Sonoff T1 3CH | Sonoff T1 3-gang Wifi Light Switch |
| 31 Supla Espablo | 2-gang Wifi Module |
| 32 Witty Cloud | Witty Cloud ESP8266 Wifi Development Board |
| 33 Yunshan Relay | ESP8266 Wifi Network Relay Module |
| 34 MagicHome | MagicHome, Flux-light and some Arilux LC10 RGB(W) Led Controller |
| 35 Luani HVIO | Luani ESP8266 Wifi I/O Module |
| 36 KMC 70011 | KMC Wifi Smart Socket with Energy Monitoring |
| 37 Arilux LC01 | Arilux AL-LC01 RGB Led Controller |
| 38 Arilux LC11 | Arilux AL-LC11 RGBWW Led Controller |
| 39 Sonoff Dual R2 | Sonoff Dual R2 Wifi Smart Switch |
| 40 Arilux LC06 | Arilux AL-LC06 RGB(WW) Led Controller |
| 41 Sonoff S31 | Sonoff S31 Wifi Smart Socket with Energy Monitoring |
| 42 Zengge WF017 | Zengge WF017 Wifi RGB(W) Led Controller |
| 43 Sonoff Pow R2 | Sonoff Pow R2 Wifi Smart Switch with Energy Monitoring |
| 44 Sonoff iFan02 | Sonoff iFan02 Wifi Smart Ceiling Fan with Light |
| 45 BlitzWolf SHP2 | BlitzWolf BW-SHP2, BW-SHP6, HomeCube SP1, Gosund SP111 Wifi Smart Switch with Energy Monitoring |
| 46 Shelly 1 | Shelly 1 Open Source Wifi Relay Module |
| 47 Shelly 2 | Shelly 2 Wifi 2-gang Relay Module with Energy Monitoring |
| 48 Xiaomi Philips | Xiaomi Philips Wifi WW Led Bulb |
| 49 Neo Coolcam | Neo Coolcam Wifi Smart Socket |
| 50 ESP Switch | ESP Switch 4-gang Wifi Switch with Leds |
| 51 OBI Socket | OBI Wifi Smart Socket |
| 52 Teckin | Teckin SP20, SP22 Wifi Smart Switch with Energy Monitoring |
| 53 AplicWDP303075 | Aplic WDP 303075 CSL Wifi Smart Switch with Energy Monitoring |
| 54 Tuya Dimmer | MIUO (and other Tuya based) Wifi Dimmer for Incandescent Lights and Led |
Provided Binary Downloads
The following binary downloads have been compiled with ESP8266/Arduino library version 2.3.0
- sonoff-minimal.bin = The Minimal version allows intermediate OTA uploads to support larger versions and does NOT change any persistent parameter. This version should NOT be used for initial installation.
- sonoff-classic.bin = The Classic version allows initial installation using either WifiManager, Wps or SmartConfig.
- sonoff.bin = The Sonoff version without Wps and SmartConfig configuration but adds more sensors.
- sonoff-BG.bin to sonoff-TW.bin = The Sonoff version without Wps and SmartConfig configuration in different languages.
- sonoff-sensors.bin = The Sensors version without Wps and SmartConfig configuration but adds even more useful sensors.
- sonoff-display.bin = The Display version without Wps and SmartConfig configuration but adds display support.
- sonoff-knx.bin = The Knx version without Wps and SmartConfig configuration and some other features but adds KNX support.
See Tasmota ESP/Arduino library version related issues why these files are still released using ESP/Arduino library version v2.3.0.
Available Features and Sensors
| Feature or Sensor | minimal | basic | classic | sonoff | knx | sensors | Remarks |
|---|---|---|---|---|---|---|---|
| ESP/Arduino lib v2.3.0 | 343k | 425k | 484k | 490k | 508k | 517k | |
| ESP/Arduino lib v2.4.2 | 372k | 451k | 497k | 517k | 533k | 541k | No sleep |
| MY_LANGUAGE en-GB | x | x | x | x | x | x | |
| MQTT_LIBRARY_TYPE PUBSUBCLIENT | x | x | x | x | x | x | |
| USE_WPS | - | - | x | - | - | - | WPS |
| USE_SMARTCONFIG | - | - | x | - | - | - | SmartConfig |
| USE_ARDUINO_OTA | - | - | - | - | - | - | |
| USE_DOMOTICZ | - | - | x | x | x | x | |
| USE_HOME_ASSISTANT | - | - | x | x | x | x | |
| USE_MQTT_TLS | - | - | - | - | - | - | |
| USE_KNX | - | - | - | - | x | - | |
| USE_WEBSERVER | x | x | x | x | x | x | WifiManager |
| USE_EMULATION | - | x | x | x | - | x | |
| USE_DISCOVERY | - | - | x | x | x | x | |
| WEBSERVER_ADVERTISE | - | - | x | x | x | x | |
| MQTT_HOST_DISCOVERY | - | - | x | x | x | x | |
| USE_TIMERS | - | x | - | x | x | x | |
| USE_TIMERS_WEB | - | x | - | x | x | x | |
| USE_SUNRISE | - | x | - | x | x | x | |
| USE_RULES | - | x | - | x | x | x | |
| USE_ADC_VCC | x | x | x | x | x | - | |
| USE_DS18B20 | - | - | - | - | - | - | Single sensor |
| USE_DS18x20 | - | - | x | x | x | x | Multiple sensors |
| USE_DS18x20_LEGACY | - | - | - | - | - | - | Multiple sensors |
| Feature or Sensor | minimal | basic | classic | sonoff | knx | sensors | |
| USE_I2C | - | - | - | x | x | x | |
| USE_SHT | - | - | - | x | x | x | |
| USE_HTU | - | - | - | x | x | x | |
| USE_BMP | - | - | - | x | x | x | |
| USE_BME680 | - | - | - | - | - | x | |
| USE_BH1750 | - | - | - | x | x | x | |
| USE_VEML6070 | - | - | - | - | - | x | |
| USE_ADS1115 | - | - | - | - | - | x | |
| USE_ADS1115_I2CDEV | - | - | - | - | - | - | |
| USE_INA219 | - | - | - | - | - | x | |
| USE_SHT3X | - | - | - | x | x | x | |
| USE_TSL2561 | - | - | - | - | - | x | |
| USE_MGS | - | - | - | - | - | x | |
| USE_SGP30 | - | - | - | x | x | x | |
| USE_SI1145 | - | - | - | - | - | x | |
| USE_LM75AD | - | - | - | x | x | x | |
| USE_APDS9960 | - | - | - | - | - | - | |
| USE_MCP230xx | - | - | - | - | - | - | |
| USE_PCA9685 | - | - | - | - | - | - | |
| USE_MPR121 | - | - | - | - | - | - | |
| USE_CCS811 | - | - | - | - | - | - | |
| USE_MPU6050 | - | - | - | - | - | - | |
| USE_DS3231 | - | - | - | - | - | - | |
| Feature or Sensor | minimal | basic | classic | sonoff | knx | sensors | |
| USE_SPI | - | - | - | - | - | - | |
| USE_MHZ19 | - | - | - | x | x | x | |
| USE_SENSEAIR | - | - | - | x | x | x | |
| USE_PMS5003 | - | - | - | x | x | x | |
| USE_NOVA_SDS | - | - | - | x | x | x | |
| USE_PZEM004T | - | - | - | x | x | x | |
| USE_PZEM_AC | - | - | - | x | x | x | |
| USE_PZEM_DC | - | - | - | x | x | x | |
| USE_MCP39F501 | - | x | - | x | x | x | |
| USE_SERIAL_BRIDGE | - | - | - | x | x | x | |
| USE_SDM120 | - | - | - | - | - | x | |
| USE_SDM630 | - | - | - | - | - | x | |
| USE_MP3_PLAYER | - | - | - | - | - | x | |
| USE_TUYA_DIMMER | - | x | - | x | x | x | |
| USE_IR_REMOTE | - | - | - | x | x | x | |
| USE_IR_HVAC | - | - | - | - | - | x | |
| USE_IR_RECEIVE | - | - | - | x | x | x | |
| USE_WS2812 | - | - | x | x | x | x | |
| USE_WS2812_DMA | - | - | - | - | - | - | |
| USE_ARILUX_RF | - | - | - | x | x | x | |
| USE_SR04 | - | - | - | x | x | x | |
| USE_TM1638 | - | - | - | - | - | x | |
| USE_HX711 | - | - | - | x | x | x | |
| USE_RF_FLASH | - | - | - | x | x | x | |
| USE_TX20_WIND_SENSOR | - | - | - | x | x | x | |
| USE_RC_SWITCH | - | - | - | x | x | x | |
| USE_DISPLAY | - | - | - | - | - | - |
Changelog
Version 6.3.0 20181030
- Change web Configure Module GPIO drop down list order for better readability
- Change status JSON message providing more switch and retain information
- Change xsns_17_senseair.ino to use TasmotaModbus library
- Change MCP230xx driver
- Change PubSubClient Mqtt library to non-blocking EspEasy version
- Change energy monitoring using energy sensor driver modules
- Change Webserver page handler for easier extension (thx to Adrian Scillato)
- Change pinmode for no-pullup defined switches to pullup when configured as switchmode PUSHBUTTON (=3 and up) (#3896)
- Change default OTA Url to http://thehackbox.org/tasmota/release/sonoff.bin (#4170)
- Remove support for MQTT Client esp-mqtt-arduino by #define MQTT_LIBRARY_TYPE MQTT_ESPMQTTARDUINO
- Remove commands PowerCal, VoltageCal and CurrentCal as more functionality is provided by commands PowerSet, VoltageSet and CurrentSet
- Remove restart after ntpserver change and force NTP re-sync (#3890)
- Fix showing Period Power in energy threshold messages
- Fix header file execution order by renaming user_config.h to my_user_config.h
- Fix some TSL2561 driver issues (#3681)
- Fix KNX PA exception. Regression from 6.2.1 buffer overflow caused by subStr() (#3700, #3710)
- Fix setting and getting color temperature for Philips Hue emulation (#3733)
- Fix ButtonRetain to not use default topic for clearing retain messages (#3737)
- Fix syslog when emulation is selected (#2109, #3784)
- Fix rule trigger POWER1#STATE execution after restart and SetOption0 is 0 (#3856)
- Fix Home Assistant forced light discovery (#3908)
- Fix invalid configuration restores and decode_config.py crc error when savedata = 0 (#3918)
- Fix timer offset -00:00 causing 12:00 hour offset (#3923)
- Fix I2CScan invalid JSON error message (#3925)
- Fix exception when wrong Domoticz JSON message is received (#3963)
- Fix Sonoff Bridge RfRaw receive (#4080, #4085)
- Fix possible wifi connection error (#4044, #4083)
- Fix invalid JSON floating point result from nan (Not a Number) and inf (Infinity) into null (#4147)
- Fix rule mqtt#connected trigger when mqtt is disabled (#4149)
- Add support for LCD, Matrix, TFT and Oled displays
- Add support for Neo Coolcam Wifi Smart Power Plug
- Add support for Michael Haustein ESP Switch
- Add support for MQTT Client based on lwmqtt to be selected by #define MQTT_LIBRARY_TYPE MQTT_ARDUINOMQTT
- Add support for DS3231 Real Time Clock
- Add support for HX711 Load Cell with optional web GUI scale interface to demonstrate easy GUI plug-in
- Add support for serial 8N2 communication to TasmotaModbus and TasmotaSerial libraries
- Add support for RF transceiving using library RcSwitch (#2702)
- Add support for Shelly 1 and Shelly 2 (#2789)
- Add support for La Crosse TX20 Anemometer (#2654, #3146)
- Add support for MP3 player using DFRobot RB-DFR-562 (#3723)
- Add Support for Xiaomi-Philips Bulbs (#3787)
- Add support for PCA9685 12bit 16pin hardware PWM driver (#3866)
- Add support for EXS Relay V5.0 (#3810)
- Add support for OBI Power Socket (#1988, #3944)
- Add support for Teckin Power Socket with Energy Monitoring (#3950)
- Add support for Pzem-003/017 DC Energy monitoring module (#3694)
- Add support for Pzem-014/016 AC Energy monitoring module (#3694)
- Add support for CSL Aplic WDP 303075 Power Socket with Energy Monitoring (#3991, #3996)
- Add support for Tuya Dimmer (#469, #4075)
- Add command Display to show all settings at once
- Add command SerialSend5 to send raw serial data like "A5074100545293"
- Add command WebRefresh 1000..10000 to control web page refresh in milliseconds. Default is 2345
- Add command WeightRes 0..3 to control display of decimals for kilogram
- Add command RGBWWTable to support color calibration (#3933)
- Add command Reset 4 (reset to defaults but keep wifi params) and Reset 5 (as reset 4 and also erase flash) (#4061)
- Add command SetOption35 0..255 (seconds) to delay mDNS initialization to control possible Wifi connect problems
- Add command SetOption52 0/1 to control display of optional time offset from UTC in JSON messages (#3629, #3711)
- Add command SetOption53 0/1 to toggle gui display of Hostname and IP address (#1006, #2091)
- Add authentication to HTTP web pages
- Add decimals as input to commands PowerSet, VoltageSet and CurrentSet
- Add tools/decode-config.py by Norbert Richter to decode configuration data. See file for information
- Add define USE_DISPLAYS for selecting image sonoff-display
- Add define USE_BASIC for selecting image sonoff-basic without most sensors
- Add auto reload of main web page to some web restarts
- Add TasmotaModbus library as very basic modbus wrapper for TasmotaSerial
- Add more API callbacks and document API.md
- Add Apparent Power and Reactive Power to Energy Monitoring devices (#251)
- Add token %hostname% to command FullTopic (#3018)
- Add Wifi channel number to state message (#3664)
- Add user configurable GPIO02 and GPIO03 on H801 devices (#3692)
- Add toggle function RGBW lights (#3695, #3697)
- Add network information to display start screen (#3704)
- Add sleep to Nova Fitness SDS01X sensor (#2841, #3724, #3749)
- Add Analog input AD0 enabled to sonoff-sensors.bin (#3756, #3757)
- Add power value below 5W to Sonoff Pow R2 and S31 (#3745)
- Add RF Receiver control to module MagicHome to be used on Arilux LC10 (#3792)
- Add userid/password option to decode-status.py (#3796)
- Add delay after restart before processing rule sensor data (#3811)
- Add force_update to Home Assistant discovery (#3873)
- Add rule triggers SWITCH1#BOOT and POWER1#BOOT (#3904, #3910)
- Add Hebrew language file (#3960)
- Add TotalStartTime to Energy JSON message (#3971)
- Add whitespace removal from RfRaw and SerialSend5 (#4020)
- Add support for two BMP/BME sensors (#4195)