net: phy: aquantia: drop wrong endianness conversion for addr and CRC

On further testing on BE target with kernel test robot, it was notice
that the endianness conversion for addr and CRC in fw_load_memory was
wrong.

Drop the cpu_to_le32 conversion for addr load as it's not needed.

Use get_unaligned_le32 instead of get_unaligned for FW data word load to
correctly convert data in the correct order to follow system endian.

Also drop the cpu_to_be32 for CRC calculation as it's wrong and would
cause different CRC on BE system.
The loaded word is swapped internally and MAILBOX calculates the CRC on
the swapped word. To correctly calculate the CRC to be later matched
with the one from MAILBOX, use an u8 struct and swap the word there to
keep the same order on both LE and BE for crc_ccitt_false function.
Also add additional comments on how the CRC verification for the loaded
section works.

CRC is calculated as we load the section and verified with the MAILBOX
only after the entire section is loaded to skip additional slowdown by
loop the section data again.

Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Fixes: e93984e ("net: phy: aquantia: add firmware load support")
Tested-by: Robert Marko <[email protected]> # ipq8072 LE device
Signed-off-by: Christian Marangi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

drivers/net/phy/aquantia/aquantia_firmware.c

@@ -93,9 +93,6 @@ static int aqr_fw_load_memory(struct phy_device *phydev, u32 addr,
 	u16 crc = 0, up_crc;
 	size_t pos;
 
-	/* PHY expect addr in LE */
-	addr = (__force u32)cpu_to_le32(addr);
-
 	phy_write_mmd(phydev, MDIO_MMD_VEND1,
 		      VEND1_GLOBAL_MAILBOX_INTERFACE1,
 		      VEND1_GLOBAL_MAILBOX_INTERFACE1_CRC_RESET);
@@ -110,10 +107,11 @@ static int aqr_fw_load_memory(struct phy_device *phydev, u32 addr,
 	 * If a firmware that is not word aligned is found, please report upstream.
 	 */
 	for (pos = 0; pos < len; pos += sizeof(u32)) {
+		u8 crc_data[4];
 		u32 word;
 
 		/* FW data is always stored in little-endian */
-		word = get_unaligned((const u32 *)(data + pos));
+		word = get_unaligned_le32((const u32 *)(data + pos));
 
 		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_GLOBAL_MAILBOX_INTERFACE5,
 			      VEND1_GLOBAL_MAILBOX_INTERFACE5_MSW_DATA(word));
@@ -124,15 +122,21 @@ static int aqr_fw_load_memory(struct phy_device *phydev, u32 addr,
 			      VEND1_GLOBAL_MAILBOX_INTERFACE1_EXECUTE |
 			      VEND1_GLOBAL_MAILBOX_INTERFACE1_WRITE);
 
-		/* calculate CRC as we load data to the mailbox.
-		 * We convert word to big-endian as PHY is BE and mailbox will
-		 * return a BE CRC.
+		/* Word is swapped internally and MAILBOX CRC is calculated
+		 * using big-endian order. Mimic what the PHY does to have a
+		 * matching CRC...
 		 */
-		word = (__force u32)cpu_to_be32(word);
-		crc = crc_ccitt_false(crc, (u8 *)&word, sizeof(word));
-	}
+		crc_data[0] = word >> 24;
+		crc_data[1] = word >> 16;
+		crc_data[2] = word >> 8;
+		crc_data[3] = word;
 
+		/* ...calculate CRC as we load data... */
+		crc = crc_ccitt_false(crc, crc_data, sizeof(crc_data));
+	}
+	/* ...gets CRC from MAILBOX after we have loaded the entire section... */
 	up_crc = phy_read_mmd(phydev, MDIO_MMD_VEND1, VEND1_GLOBAL_MAILBOX_INTERFACE2);
+	/* ...and make sure it does match our calculated CRC */
 	if (crc != up_crc) {
 		phydev_err(phydev, "CRC mismatch: calculated 0x%04x PHY 0x%04x\n",
 			   crc, up_crc);