cpu/samd5x/periph_can: fix RX

CAN required CLK_CANx_APB and CLK_CANx_APB to be running and will not
request any clock by itself. We can ensure both clocks to be running
by preventing the MCU from entering IDLE state.

The SAMD5x/SAME5x Family Data Sheet says in Section
"39.6.9 Sleep Mode Operation" says:

> The CAN can be configured to operate in any idle sleep mode. The CAN
> cannot operate in Standby sleep mode.
>
> [...]
>
> To leave low power mode, CLK_CANx_APB and GCLK_CANx must be active
> before writing CCCR.CSR to '0'. The CAN will acknowledge this by
> resetting CCCR.CSA = 0. Afterwards, the application can restart CAN
> communication by resetting bit CCCR.INIT.

tl;dr: At most SAM0_PM_IDLE is allowed while not shutting down the CAN
controller, but even that will pause communication (including RX).

Apparently, the CAN controller was never tested without also using the
USB peripheral, which kept the clocks running as side effect.

cpu/samd5x/periph/can.c

@@ -20,9 +20,10 @@
 #include <assert.h>
 #include <string.h>
 
+#include "can/device.h"
 #include "periph/can.h"
 #include "periph/gpio.h"
-#include "can/device.h"
+#include "pm_layered.h"
 
 #define ENABLE_DEBUG 0
 #include "debug.h"
@@ -107,6 +108,30 @@ static const struct can_bittiming_const bittiming_const = {
 
 static int _power_on(can_t *dev)
 {
+    /* CAN required CLK_CANx_APB and GCLK_CANx to be running and will not
+     * request any clock by itself. We can ensure both clocks to be running
+     * by preventing the MCU from entering IDLE state.
+     *
+     * The SAMD5x/SAME5x Family Data Sheet says in Section
+     * "39.6.9 Sleep Mode Operation" says:
+     *
+     * > The CAN can be configured to operate in any idle sleep mode. The CAN
+     * > cannot operate in Standby sleep mode.
+     * >
+     * > [...]
+     * >
+     * > To leave low power mode, CLK_CANx_APB and GCLK_CANx must be active
+     * > before writing CCCR.CSR to '0'. The CAN will acknowledge this by
+     * > resetting CCCR.CSA = 0. Afterwards, the application can restart CAN
+     * > communication by resetting bit CCCR.INIT.
+     *
+     * tl;dr: At most SAM0_PM_IDLE is allowed while not shutting down the CAN
+     * controller, but even that will pause communication (including RX).
+     */
+    if (IS_USED(MODULE_PM_LAYERED)) {
+        pm_block(SAM0_PM_IDLE);
+    }
+
     if (dev->conf->can == CAN0) {
         DEBUG_PUTS("CAN0 controller is used");
         MCLK->AHBMASK.reg |= MCLK_AHBMASK_CAN0;
@@ -125,6 +150,10 @@ static int _power_on(can_t *dev)
 
 static int _power_off(can_t *dev)
 {
+    if (IS_USED(MODULE_PM_LAYERED)) {
+        pm_unblock(SAM0_PM_IDLE);
+    }
+
     if (dev->conf->can == CAN0) {
         DEBUG_PUTS("CAN0 controller is used");
         MCLK->AHBMASK.reg &= ~MCLK_AHBMASK_CAN0;