fichero actualizado

Calibration/02.0.5mm-thin-wall_profile.ini

@@ -0,0 +1,100 @@
+[profile]
+filament_diameter = 2.89
+nozzle_size = 0.5
+machine_center_x = 85
+machine_center_y = 85
+wall_thickness = 0.6
+flip_x = False
+flip_y = False
+flip_z = False
+swap_xz = False
+swap_yz = False
+model_scale = 0.85625
+model_rotate_base = 270
+layer_height = 0.3
+retraction_enable = True
+solid_layer_thickness = 0.9
+fill_density = 0
+skirt_line_count = 1
+skirt_gap = 3.0
+print_speed = 25
+print_temperature = 220
+print_bed_temperature = 110
+support = None
+enable_raft = False
+filament_density = 0.85
+retraction_min_travel = 2
+retraction_speed = 16
+retraction_amount = 2.5
+retraction_extra = 0.0
+travel_speed = 90
+max_z_speed = 3
+bottom_layer_speed = 18
+cool_min_layer_time = 10
+fan_enabled = False
+bottom_thickness = 0.38
+enable_skin = False
+plugin_config = (lp1
+	.
+extra_base_wall_thickness = 0.0
+cool_min_feedrate = 10
+fan_layer = 1
+fan_speed = 100
+fan_speed_max = 100
+raft_margin = 5
+raft_base_material_amount = 100
+raft_interface_material_amount = 100
+support_rate = 50
+support_distance = 0.5
+infill_type = Line
+solid_top = True
+fill_overlap = 25
+bridge_speed = 100
+sequence = Loops > Perimeter > Infill
+force_first_layer_sequence = True
+joris = False
+retract_on_jumps_only = False
+hop_on_move = False
+
+[alterations]
+start.gcode = ;Sliced {filename} at: {day} {date} {time}
+	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
+	;Print time: {print_time}
+	;Filament used: {filament_amount}m {filament_weight}g
+	;Filament cost: {filament_cost}
+	G21        ;metric values
+	G90        ;absolute positioning
+	M107       ;start with the fan off
+	G28 X0 Y0  ;move X/Y to min endstops
+	G28 Z0     ;move Z to min endstops
+	G1 Z0.7 F{max_z_speed}  ;z offset
+	G92 X0 Y0 Z0 E0          ;reset software position to front/left/z=0.0
+	G1 Z5.0 F{max_z_speed}  ;move the platform down 15mm
+	G92 E0                  ;zero the extruded length
+	G1 F200 E3              ;extrude 3mm of feed stock
+	G92 E0                  ;zero the extruded length again
+	;go to the middle of the platform (disabled, as there is no need to go to the center)
+	;G1 X{machine_center_x} Y{machine_center_y} F{travel_speed}
+	G1 F{travel_speed}
+end.gcode = ;End GCode
+	M104 S0                     ;extruder heater off
+	M140 S0                     ;heated bed heater off (if you have it)
+	G91                                    ;relative positioning
+	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
+	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
+	M84                         ;steppers off
+	G90                         ;absolute positioning
+nextobject.gcode = ;Move to next object on the platform. clear_z is the minimal z height we need to make sure we do not hit any objects.
+	G92 E0
+	G91                                    ;relative positioning
+	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
+	G1 Z+0.5 E-5 F{travel_speed}           ;move Z up a bit and retract filament even more
+	G90                                    ;absolute positioning
+	G1 Z{clear_z} F{max_z_speed}
+	G92 E0
+	G1 X{machine_center_x} Y{machine_center_y} F{travel_speed}
+	G1 F200 E6
+	G92 E0
+replace.csv = 
+

Printers/Printrbot_v2/Plate/4-5-11-12-14-15_stl.scad

@@ -0,0 +1,7 @@
+translate([55, 121, 0]) rotate([0, 0, 0]) import_stl("11-coupling-x2.stl");
+translate([149, 124, 0]) rotate([0, 0, 0]) import_stl("12-pb1-z-endstop_v3.stl");
+translate([152, 26, 0]) rotate([0, 0, 0]) import_stl("14-Y_idler-1.stl");
+translate([76, 77, 0]) rotate([0, 0, 0]) import_stl("04-pbm-X-Carriage-x1_v2.stl");
+translate([90, 121, 0]) rotate([0, 0, 0]) import_stl("11-coupling-x2.stl");
+translate([109, 66, 5.58932e-15]) rotate([0, 0, -50]) import_stl("21-buddasch_mount_pb.stl");
+translate([110, 94, 0]) rotate([0, 0, 0]) import_stl("20-hotend_adapter.stl");

Printers/Printrbot_v2/Plate/skeinforge.sh

@@ -0,0 +1,11 @@
+!/bin/bash
+#- Script para ejecutar de una sola vez el craft de varios ficheros stl
+#- Es necesario cambiar la variable DIR y poner el directorio
+#- donde está instalado skeinforge
+#- Santiago Lopez Pina - Julio 2012
+
+DIR="/Applications/"
+mkdir gcodes
+for i in `ls *.stl`;do
+	 python ${DIR}/skeinforge/skeinforge_application/skeinforge_utilities/skeinforge_craft.py $i;done
+mv *.gcode ./gcodes