[1.1.x] Add thermocouple with AD8495 support

Marlin/Conditionals_post.h

@@ -265,7 +265,9 @@
   /**
    * Temp Sensor defines
    */
-  #if TEMP_SENSOR_0 == -3
+  #if TEMP_SENSOR_0 == -4
+    #define HEATER_0_USES_AD8495
+  #elif TEMP_SENSOR_0 == -3
     #define HEATER_0_USES_MAX6675
     #define MAX6675_IS_MAX31855
     #define MAX6675_TMIN -270
@@ -284,8 +286,12 @@
     #define HEATER_0_USES_THERMISTOR
   #endif
 
-  #if TEMP_SENSOR_1 <= -2
-    #error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_1"
+  #if TEMP_SENSOR_1 == -4
+    #define HEATER_1_USES_AD8495
+  #elif TEMP_SENSOR_1 == -3
+    #error "MAX31855 Thermocouples not supported for TEMP_SENSOR_1"
+  #elif TEMP_SENSOR_1 == -2
+    #error "MAX6675 Thermocouples not supported for TEMP_SENSOR_1"
   #elif TEMP_SENSOR_1 == -1
     #define HEATER_1_USES_AD595
   #elif TEMP_SENSOR_1 == 0
@@ -296,8 +302,12 @@
     #define HEATER_1_USES_THERMISTOR
   #endif
 
-  #if TEMP_SENSOR_2 <= -2
-    #error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_2"
+  #if TEMP_SENSOR_2 == -4
+    #define HEATER_2_USES_AD8495
+  #elif TEMP_SENSOR_2 == -3
+    #error "MAX31855 Thermocouples not supported for TEMP_SENSOR_2"
+  #elif TEMP_SENSOR_2 == -2
+    #error "MAX6675 Thermocouples not supported for TEMP_SENSOR_2"
   #elif TEMP_SENSOR_2 == -1
     #define HEATER_2_USES_AD595
   #elif TEMP_SENSOR_2 == 0
@@ -308,8 +318,12 @@
     #define HEATER_2_USES_THERMISTOR
   #endif
 
-  #if TEMP_SENSOR_3 <= -2
-    #error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_3"
+  #if TEMP_SENSOR_3 == -4
+    #define HEATER_3_USES_AD8495
+  #elif TEMP_SENSOR_3 == -3
+    #error "MAX31855 Thermocouples not supported for TEMP_SENSOR_3"
+  #elif TEMP_SENSOR_3 == -2
+    #error "MAX6675 Thermocouples not supported for TEMP_SENSOR_3"
   #elif TEMP_SENSOR_3 == -1
     #define HEATER_3_USES_AD595
   #elif TEMP_SENSOR_3 == 0
@@ -320,8 +334,12 @@
     #define HEATER_3_USES_THERMISTOR
   #endif
 
-  #if TEMP_SENSOR_4 <= -2
-    #error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_4"
+  #if TEMP_SENSOR_4 == -4
+    #define HEATER_4_USES_AD8495
+  #elif TEMP_SENSOR_4 == -3
+    #error "MAX31855 Thermocouples not supported for TEMP_SENSOR_4"
+  #elif TEMP_SENSOR_4 == -2
+    #error "MAX6675 Thermocouples not supported for TEMP_SENSOR_4"
   #elif TEMP_SENSOR_4 == -1
     #define HEATER_4_USES_AD595
   #elif TEMP_SENSOR_4 == 0
@@ -332,8 +350,12 @@
     #define HEATER_4_USES_THERMISTOR
   #endif
 
-  #if TEMP_SENSOR_BED <= -2
-    #error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_BED"
+  #if TEMP_SENSOR_BED == -4
+    #define BED_USES_AD8495
+  #elif TEMP_SENSOR_BED == -3
+    #error "MAX31855 Thermocouples not supported for TEMP_SENSOR_BED"
+  #elif TEMP_SENSOR_BED == -2
+    #error "MAX6675 Thermocouples not supported for TEMP_SENSOR_BED"
   #elif TEMP_SENSOR_BED == -1
     #define BED_USES_AD595
   #elif TEMP_SENSOR_BED == 0
@@ -344,15 +366,22 @@
     #define BED_USES_THERMISTOR
   #endif
 
-  #if TEMP_SENSOR_CHAMBER <= -2
-    #error "MAX6675 / MAX31855 Thermocouples not supported for TEMP_SENSOR_CHAMBER"
+  #if TEMP_SENSOR_CHAMBER == -4
+    #define CHAMBER_USES_AD8495
+  #elif TEMP_SENSOR_CHAMBER == -3
+    #error "MAX31855 Thermocouples not supported for TEMP_SENSOR_CHAMBER"
+  #elif TEMP_SENSOR_CHAMBER == -2
+    #error "MAX6675 Thermocouples not supported for TEMP_SENSOR_CHAMBER"
   #elif TEMP_SENSOR_CHAMBER == -1
     #define CHAMBER_USES_AD595
   #elif TEMP_SENSOR_CHAMBER > 0
     #define THERMISTORCHAMBER TEMP_SENSOR_CHAMBER
     #define CHAMBER_USES_THERMISTOR
   #endif
 
+  #define HEATER_USES_AD8495 (ENABLED(HEATER_0_USES_AD8495) || ENABLED(HEATER_1_USES_AD8495) || ENABLED(HEATER_2_USES_AD8495) || ENABLED(HEATER_3_USES_AD8495) || ENABLED(HEATER_4_USES_AD8495))
+  #define HEATER_USES_AD595 (ENABLED(HEATER_0_USES_AD595) || ENABLED(HEATER_1_USES_AD595) || ENABLED(HEATER_2_USES_AD595) || ENABLED(HEATER_3_USES_AD595) || ENABLED(HEATER_4_USES_AD595))
+
   /**
    * Default hotend offsets, if not defined
    */
@@ -662,12 +691,13 @@
   #endif
 
   // Endstops and bed probe
-  #define HAS_X_MIN (PIN_EXISTS(X_MIN) && !IS_X2_ENDSTOP(X,MIN) && !IS_Y2_ENDSTOP(X,MIN) && !IS_Z2_OR_PROBE(X,MIN))
-  #define HAS_X_MAX (PIN_EXISTS(X_MAX) && !IS_X2_ENDSTOP(X,MAX) && !IS_Y2_ENDSTOP(X,MAX) && !IS_Z2_OR_PROBE(X,MAX))
-  #define HAS_Y_MIN (PIN_EXISTS(Y_MIN) && !IS_X2_ENDSTOP(Y,MIN) && !IS_Y2_ENDSTOP(Y,MIN) && !IS_Z2_OR_PROBE(Y,MIN))
-  #define HAS_Y_MAX (PIN_EXISTS(Y_MAX) && !IS_X2_ENDSTOP(Y,MAX) && !IS_Y2_ENDSTOP(Y,MAX) && !IS_Z2_OR_PROBE(Y,MAX))
-  #define HAS_Z_MIN (PIN_EXISTS(Z_MIN) && !IS_X2_ENDSTOP(Z,MIN) && !IS_Y2_ENDSTOP(Z,MIN) && !IS_Z2_OR_PROBE(Z,MIN))
-  #define HAS_Z_MAX (PIN_EXISTS(Z_MAX) && !IS_X2_ENDSTOP(Z,MAX) && !IS_Y2_ENDSTOP(Z,MAX) && !IS_Z2_OR_PROBE(Z,MAX))
+  #define HAS_STOP_TEST(A,M) (PIN_EXISTS(A##_##M) && !IS_X2_ENDSTOP(A,M) && !IS_Y2_ENDSTOP(A,M) && !IS_Z2_OR_PROBE(A,M))
+  #define HAS_X_MIN HAS_STOP_TEST(X,MIN)
+  #define HAS_X_MAX HAS_STOP_TEST(X,MAX)
+  #define HAS_Y_MIN HAS_STOP_TEST(Y,MIN)
+  #define HAS_Y_MAX HAS_STOP_TEST(Y,MAX)
+  #define HAS_Z_MIN HAS_STOP_TEST(Z,MIN)
+  #define HAS_Z_MAX HAS_STOP_TEST(Z,MAX)
   #define HAS_X2_MIN (PIN_EXISTS(X2_MIN))
   #define HAS_X2_MAX (PIN_EXISTS(X2_MAX))
   #define HAS_Y2_MIN (PIN_EXISTS(Y2_MIN))
@@ -676,15 +706,19 @@
   #define HAS_Z2_MAX (PIN_EXISTS(Z2_MAX))
   #define HAS_Z_MIN_PROBE_PIN (PIN_EXISTS(Z_MIN_PROBE))
 
-  // Thermistors
-  #define HAS_TEMP_0 (PIN_EXISTS(TEMP_0) && TEMP_SENSOR_0 != 0 && TEMP_SENSOR_0 > -2)
-  #define HAS_TEMP_1 (PIN_EXISTS(TEMP_1) && TEMP_SENSOR_1 != 0 && TEMP_SENSOR_1 > -2)
-  #define HAS_TEMP_2 (PIN_EXISTS(TEMP_2) && TEMP_SENSOR_2 != 0 && TEMP_SENSOR_2 > -2)
-  #define HAS_TEMP_3 (PIN_EXISTS(TEMP_3) && TEMP_SENSOR_3 != 0 && TEMP_SENSOR_3 > -2)
-  #define HAS_TEMP_4 (PIN_EXISTS(TEMP_4) && TEMP_SENSOR_4 != 0 && TEMP_SENSOR_4 > -2)
-  #define HAS_TEMP_HOTEND (HAS_TEMP_0 || ENABLED(HEATER_0_USES_MAX6675))
-  #define HAS_TEMP_BED (PIN_EXISTS(TEMP_BED) && TEMP_SENSOR_BED != 0 && TEMP_SENSOR_BED > -2)
-  #define HAS_TEMP_CHAMBER (PIN_EXISTS(TEMP_CHAMBER) && TEMP_SENSOR_CHAMBER != 0 && TEMP_SENSOR_CHAMBER > -2)
+  // ADC Temp Sensors (Thermistor or Thermocouple with amplifier ADC interface)
+  #define HAS_ADC_TEST(P) (PIN_EXISTS(TEMP_##P) && TEMP_SENSOR_##P != 0 && TEMP_SENSOR_##P > -2)
+  #define HAS_TEMP_ADC_0 (HAS_ADC_TEST(0) && DISABLED(HEATER_0_USES_MAX6675))
+  #define HAS_TEMP_ADC_1 HAS_ADC_TEST(1)
+  #define HAS_TEMP_ADC_2 HAS_ADC_TEST(2)
+  #define HAS_TEMP_ADC_3 HAS_ADC_TEST(3)
+  #define HAS_TEMP_ADC_4 HAS_ADC_TEST(4)
+  #define HAS_TEMP_ADC_BED HAS_ADC_TEST(BED)
+  #define HAS_TEMP_ADC_CHAMBER HAS_ADC_TEST(CHAMBER)
+
+  #define HAS_TEMP_HOTEND (HAS_TEMP_ADC_0 || ENABLED(HEATER_0_USES_MAX6675))
+  #define HAS_TEMP_BED HAS_TEMP_ADC_BED
+  #define HAS_TEMP_CHAMBER HAS_TEMP_ADC_CHAMBER
 
   // Heaters
   #define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))

Marlin/Configuration.h

@@ -259,6 +259,7 @@
  *
  * Temperature sensors available:
  *
+ *    -4 : thermocouple with AD8495
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
  *    -2 : thermocouple with MAX6675 (only for sensor 0)
  *    -1 : thermocouple with AD595
@@ -299,7 +300,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
+ * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0

Marlin/Configuration_adv.h

@@ -182,10 +182,12 @@
 
 // @section temperature
 
-//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
-//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
-#define TEMP_SENSOR_AD595_OFFSET 0.0
-#define TEMP_SENSOR_AD595_GAIN   1.0
+// Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
+// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
+#define TEMP_SENSOR_AD595_OFFSET  0.0
+#define TEMP_SENSOR_AD595_GAIN    1.0
+#define TEMP_SENSOR_AD8495_OFFSET 0.0
+#define TEMP_SENSOR_AD8495_GAIN   1.0
 
 /**
  * Controller Fan

Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h

@@ -259,6 +259,7 @@
  *
  * Temperature sensors available:
  *
+ *    -4 : thermocouple with AD8495
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
  *    -2 : thermocouple with MAX6675 (only for sensor 0)
  *    -1 : thermocouple with AD595
@@ -299,7 +300,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
+ * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  */
 #define TEMP_SENSOR_0 7
 #define TEMP_SENSOR_1 0

Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h

@@ -182,10 +182,12 @@
 
 // @section temperature
 
-//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
-//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
-#define TEMP_SENSOR_AD595_OFFSET 0.0
-#define TEMP_SENSOR_AD595_GAIN   1.0
+// Calibration for AD595 / AD8495 sensor to adjust temperature measurements.
+// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET.
+#define TEMP_SENSOR_AD595_OFFSET  0.0
+#define TEMP_SENSOR_AD595_GAIN    1.0
+#define TEMP_SENSOR_AD8495_OFFSET 0.0
+#define TEMP_SENSOR_AD8495_GAIN   1.0
 
 /**
  * Controller Fan

Marlin/example_configurations/AliExpress/CL-260/Configuration.h

@@ -259,6 +259,7 @@
  *
  * Temperature sensors available:
  *
+ *    -4 : thermocouple with AD8495
  *    -3 : thermocouple with MAX31855 (only for sensor 0)
  *    -2 : thermocouple with MAX6675 (only for sensor 0)
  *    -1 : thermocouple with AD595
@@ -299,7 +300,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
+ * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0