Added support for SKR Pro V1.1

Marlin/Configuration.h

@@ -97,7 +97,8 @@
 //#define AddonFilSensor //Adds a filamnt runout sensor to the CR20 or Ender 4
 //#define lerdgeFilSensor //Using lerdge filament sensor, which is opposite polarity to stock
 //#define DualFilSensors //Using dual filament sensors on XMax and YMAX
-#define FilamentEncoder //Using filamet jam sensor such as the Bigtreetech Encoder wheel
+//#define FilamentEncoder //Using filamet jam sensor such as the Bigtreetech Encoder wheel
+
 
 // Advanced options - Not for most users
 
@@ -131,8 +132,11 @@
 //#define Melzi_To_SBoardUpgrade // Upgrade Melzi board to 10S board
 //#define CrealitySilentBoard // Creality board with TMC2208 Standalone drivers. Disables Linear Advance
 //#define SKR13 // 32 bit board - assumes 2208 drivers
-//#define SKR13_2209
-//#define SKR13_UART // Configure SKR board with drivers in UART mode
+#define SKRPRO11
+//#define I2C_EEPROM  // use I2C EEPROM on SRK PRO v1.1 e.g AT24C256
+
+#define SKR_2209
+#define SKR_UART // Configure SKR board with drivers in UART mode
 //#define SKR13_ReverseSteppers // Some users reported directions backwards than others on SKR with various drivers.
 
  /*
@@ -312,7 +316,7 @@
   #define Z_STOP_PIN 19
 #endif
 
-#if ANY(MachineEnder2, MachineEnder3, MachineEnder5, MachineCR10) && NONE(Melzi_To_SBoardUpgrade, SKR13)
+#if ANY(MachineEnder2, MachineEnder3, MachineEnder5, MachineCR10) && NONE(Melzi_To_SBoardUpgrade, SKR13, SKRPRO11)
   #define MachineCR10Orig
 #endif
 
@@ -369,6 +373,13 @@
   #define SolidBedMounts
 #endif
 
+#if ENABLED(SKRPRO11)
+  #define FIL_RUNOUT_PIN   PE15
+  #if DISABLED(I2C_EEPROM)
+    #define FLASH_EEPROM_EMULATION
+  #endif
+#endif
+
 //Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
 
 #if NONE(MachineCR10Orig, MachineEnder4, MachineCR10SPro, MachineCRX, MachineCR10Max, MachineEnder5Plus) || ENABLED(GraphicLCD)
@@ -387,7 +398,7 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#if ENABLED(SKR13)
+#if ANY(SKR13, SKRPRO11)
   #define SERIAL_PORT -1
 #else
   #define SERIAL_PORT 0
@@ -402,6 +413,8 @@
  */
 #if ENABLED(SKR13)
   #define SERIAL_PORT_2 0
+#elif ENABLED(SKRPRO11) && NONE(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max) && DISABLED(GraphicLCD)
+  #define SERIAL_PORT_2 1
 #endif
 /**
  * This setting determines the communication speed of the printer.
@@ -421,6 +434,8 @@
 #ifndef MOTHERBOARD
   #if ENABLED(SKR13)
     #define MOTHERBOARD BOARD_BIGTREE_SKR_V1_3
+  #elif ENABLED(SKRPRO11)
+    #define MOTHERBOARD BOARD_BIGTREE_SKR_PRO_V1_1
   #elif (ENABLED(MachineCR10Orig) && DISABLED(Melzi_To_SBoardUpgrade))
     #define MOTHERBOARD BOARD_MELZI_CREALITY
   #else
@@ -1068,8 +1083,8 @@
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
 
-#if ANY(SKR13, MachineCR10SV2, CrealitySilentBoard, MachineCR10SPro, MachineCR10SProV2, MachineCR10Max) && DISABLED(SKR13_UART)
-  #if ENABLED(SKR13_2209)
+#if ANY(SKR13, SKRPRO11, MachineCR10SV2, CrealitySilentBoard, MachineCR10SPro, MachineCR10SProV2, MachineCR10Max) && DISABLED(SKR_UART)
+  #if ENABLED(SKR_2209)
     #define X_DRIVER_TYPE  TMC2209_STANDALONE
     #define Y_DRIVER_TYPE  TMC2209_STANDALONE
     #define Z_DRIVER_TYPE  TMC2209_STANDALONE
@@ -1082,8 +1097,8 @@
     #define E0_DRIVER_TYPE TMC2208_STANDALONE
     #define E1_DRIVER_TYPE TMC2208_STANDALONE
   #endif
-#elif ENABLED(SKR13, SKR13_UART)
-  #if ENABLED(SKR13_2209)
+#elif ANY(SKR13, SKRPRO11) && ENABLED(SKR_UART)
+  #if ENABLED(SKR_2209)
     #define X_DRIVER_TYPE  TMC2209
     #define Y_DRIVER_TYPE  TMC2209
     #define Z_DRIVER_TYPE  TMC2209
@@ -1394,7 +1409,7 @@
     #define PROBING_FANS_OFF          // Turn fans off when probing
   #endif
 
-  #if ENABLED(MachineEnder4) && DISABLED(SKR13)
+  #if ENABLED(MachineEnder4) && DISABLED(SKR13, SKRPRO11)
     #define SOLENOID_PROBE PIN_15
   #endif
 #endif
@@ -1843,8 +1858,10 @@
   #define FILAMENT_RUNOUT_SENSOR
 #endif
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
-  #if ENABLED(DualFilSensors) && DISABLED(SKR13)
-    #define NUM_RUNOUT_SENSORS   2     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
+  #if ENABLED(DualFilSensors)
+    #if DISABLED(SKR13,SKRPRO11)
+      #define NUM_RUNOUT_SENSORS   2     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
+    #endif
     #define FIL_RUNOUT2_PIN 15
   #else
     #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.

Marlin/Configuration_adv.h

@@ -1284,7 +1284,7 @@
   #define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
   //#define GAMES_EASTER_EGG          // Add extra blank lines above the "Games" sub-menu
 
-  #if ENABLED(SKR13)
+  #if ENABLED(SKR13, SKRPRO11)
     // Frivolous Game Options
     #define MARLIN_BRICKOUT
     #define MARLIN_INVADERS
@@ -1467,7 +1467,7 @@
  * See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
  * Mention @Sebastianv650 on GitHub to alert the author of any issues.
  */
-#if NONE(MachineCR10Orig, LowMemoryBoard, MachineCR10SPro, MachineCR10Max, SKR13, MachineCR10SV2, CrealitySilentBoard) || ENABLED(OrigLA) || ENABLED(SKR13, SKR13_UART)
+#if NONE(MachineCR10Orig, LowMemoryBoard, MachineCR10SPro, MachineCR10Max, SKR13, MachineCR10SV2, CrealitySilentBoard) || ENABLED(OrigLA) || ENABLED(SKR13, SKR_UART) || ENABLED(SKRPRO11, SKR_UART)
   #define LIN_ADVANCE
 #endif
 #if ENABLED(LIN_ADVANCE)
@@ -1604,7 +1604,7 @@
  *
  * Override the default value based on the driver type set in Configuration.h.
  */
-#if ENABLED(SKR13)
+#if ENABLED(SKR13, SKRPRO11)
   #define MINIMUM_STEPPER_PULSE 1
 #endif
 /**
@@ -1692,7 +1692,9 @@
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
 // Does not work on boards using AT90USB (USBCON) processors!
-#define EMERGENCY_PARSER
+#if DISABLED(SKRPRO11)
+  #define EMERGENCY_PARSER
+#endif
 
 // Bad Serial-connections can miss a received command by sending an 'ok'
 // Therefore some clients abort after 30 seconds in a timeout.
@@ -1737,7 +1739,7 @@
  * Note that M207 / M208 / M209 settings are saved to EEPROM.
  *
  */
- #if ENABLED(SKR13)
+ #if ENABLED(SKR13, SKRPRO11)
   #define FWRETRACT
 #endif
 #if ENABLED(FWRETRACT)
@@ -1967,7 +1969,7 @@
   #define INTERPOLATE       true  // Interpolate X/Y/Z_MICROSTEPS to 256
 
   #if AXIS_IS_TMC(X)
-    #define X_CURRENT       800        // (mA) RMS current. Multiply by 1.414 for peak current.
+    #define X_CURRENT       730        // (mA) RMS current. Multiply by 1.414 for peak current.
     #define X_CURRENT_HOME  X_CURRENT  // (mA) RMS current for sensorless homing
     #define X_MICROSTEPS     16    // 0..256
     #define X_RSENSE          0.11
@@ -1983,7 +1985,7 @@
   #endif
 
   #if AXIS_IS_TMC(Y)
-    #define Y_CURRENT       800
+    #define Y_CURRENT       730
     #define Y_CURRENT_HOME  Y_CURRENT
     #define Y_MICROSTEPS     16
     #define Y_RSENSE          0.11
@@ -1999,7 +2001,7 @@
   #endif
 
   #if AXIS_IS_TMC(Z)
-    #define Z_CURRENT       800
+    #define Z_CURRENT       850
     #define Z_CURRENT_HOME  Z_CURRENT
     #define Z_MICROSTEPS     16
     #define Z_RSENSE          0.11
@@ -2023,7 +2025,7 @@
   #endif
 
   #if AXIS_IS_TMC(E0)
-    #define E0_CURRENT      800
+    #define E0_CURRENT      730
     #define E0_MICROSTEPS    16
     #define E0_RSENSE         0.11
     #define E0_CHAIN_POS     -1
@@ -2133,7 +2135,7 @@
    */
   #define STEALTHCHOP_XY
   #define STEALTHCHOP_Z
-  #define STEALTHCHOP_E
+  //#define STEALTHCHOP_E
 
   /**
    * Optimize spreadCycle chopper parameters by using predefined parameter sets
@@ -2162,7 +2164,9 @@
    * M912 - Clear stepper driver overtemperature pre-warn condition flag.
    * M122 - Report driver parameters (Requires TMC_DEBUG)
    */
-  //#define MONITOR_DRIVER_STATUS
+  #if ENABLED(SKR_UART)
+    #define MONITOR_DRIVER_STATUS
+  #endif
 
   #if ENABLED(MONITOR_DRIVER_STATUS)
     #define CURRENT_STEP_DOWN     50  // [mA]
@@ -2179,14 +2183,14 @@
    */
   #define HYBRID_THRESHOLD
 
-  #define X_HYBRID_THRESHOLD     100  // [mm/s]
+  #define X_HYBRID_THRESHOLD     150  // [mm/s]
   #define X2_HYBRID_THRESHOLD    100
-  #define Y_HYBRID_THRESHOLD     100
+  #define Y_HYBRID_THRESHOLD     150
   #define Y2_HYBRID_THRESHOLD    100
-  #define Z_HYBRID_THRESHOLD       3
-  #define Z2_HYBRID_THRESHOLD      3
+  #define Z_HYBRID_THRESHOLD      10
+  #define Z2_HYBRID_THRESHOLD     10
   #define Z3_HYBRID_THRESHOLD      3
-  #define E0_HYBRID_THRESHOLD     30
+  #define E0_HYBRID_THRESHOLD     50
   #define E1_HYBRID_THRESHOLD     30
   #define E2_HYBRID_THRESHOLD     30
   #define E3_HYBRID_THRESHOLD     30
@@ -2243,13 +2247,15 @@
    * Beta feature!
    * Create a 50/50 square wave step pulse optimal for stepper drivers.
    */
-  //#define SQUARE_WAVE_STEPPING
+  #define SQUARE_WAVE_STEPPING
 
   /**
    * Enable M122 debugging command for TMC stepper drivers.
    * M122 S0/1 will enable continous reporting.
    */
-  //#define TMC_DEBUG
+    #if ENABLED(SKR_UART)
+      #define TMC_DEBUG
+    #endif
 
   /**
    * You can set your own advanced settings by filling in predefined functions.

Marlin/src/lcd/extensible_ui/lib/Creality_DWIN.h

@@ -92,6 +92,8 @@ namespace ExtUI {
 
 #if ENABLED(SKR13)
   #define DWIN_SERIAL MSerial
+#elif ENABLED(SKRPRO11)
+  #define DWIN_SERIAL Serial1
 #else
   #define DWIN_SERIAL Serial2
 #endif
@@ -187,4 +189,4 @@ float targetPos;
 #ifndef USER_GCODE_1
   #define USER_GCODE_1 "G28"
 #endif
-#endif
+#endif

platformio.ini

@@ -577,7 +577,7 @@ lib_deps          =
   U8glib-HAL=https://github.com/MarlinFirmware/U8glib-HAL/archive/bugfix.zip
   LiquidCrystal
   TMCStepper@>=0.5.2,<1.0.0
-  Adafruit NeoPixel
+  #Adafruit NeoPixel
   LiquidTWI2=https://github.com/lincomatic/LiquidTWI2/archive/master.zip
   Arduino-L6470=https://github.com/ameyer/Arduino-L6470/archive/dev.zip
 lib_ignore        = SoftwareSerial, SoftwareSerialM