Update 5.10.x+fslc up to v5.10.92 #524
Merged
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
commit ad3fc79 upstream. The commit 41d2d84 ("md: improve io stats accounting") could cause double fault problem per the report [1], and also it is not correct to change ->bi_end_io if md don't own it, so let's revert it. And io stats accounting will be replemented in later commits. [1]. https://lore.kernel.org/linux-raid/[email protected]/T/#t Fixes: 41d2d84 ("md: improve io stats accounting") Signed-off-by: Guoqing Jiang <[email protected]> Signed-off-by: Song Liu <[email protected]> [GM: backport to 5.10-stable] Signed-off-by: Guillaume Morin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 07edfec upstream. At CPU-hotplug time, unbind_worker() may preempt a worker while it is waking up. In that case the following scenario can happen: unbind_workers() wq_worker_running() -------------- ------------------- if (!(worker->flags & WORKER_NOT_RUNNING)) //PREEMPTED by unbind_workers worker->flags |= WORKER_UNBOUND; [...] atomic_set(&pool->nr_running, 0); //resume to worker atomic_inc(&worker->pool->nr_running); After unbind_worker() resets pool->nr_running, the value is expected to remain 0 until the pool ever gets rebound in case cpu_up() is called on the target CPU in the future. But here the race leaves pool->nr_running with a value of 1, triggering the following warning when the worker goes idle: WARNING: CPU: 3 PID: 34 at kernel/workqueue.c:1823 worker_enter_idle+0x95/0xc0 Modules linked in: CPU: 3 PID: 34 Comm: kworker/3:0 Not tainted 5.16.0-rc1+ Freescale#34 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014 Workqueue: 0x0 (rcu_par_gp) RIP: 0010:worker_enter_idle+0x95/0xc0 Code: 04 85 f8 ff ff ff 39 c1 7f 09 48 8b 43 50 48 85 c0 74 1b 83 e2 04 75 99 8b 43 34 39 43 30 75 91 8b 83 00 03 00 00 85 c0 74 87 <0f> 0b 5b c3 48 8b 35 70 f1 37 01 48 8d 7b 48 48 81 c6 e0 93 0 RSP: 0000:ffff9b7680277ed0 EFLAGS: 00010086 RAX: 00000000ffffffff RBX: ffff93465eae9c00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9346418a0000 RDI: ffff934641057140 RBP: ffff934641057170 R08: 0000000000000001 R09: ffff9346418a0080 R10: ffff9b768027fdf0 R11: 0000000000002400 R12: ffff93465eae9c20 R13: ffff93465eae9c20 R14: ffff93465eae9c70 R15: ffff934641057140 FS: 0000000000000000(0000) GS:ffff93465eac0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000001cc0c000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> worker_thread+0x89/0x3d0 ? process_one_work+0x400/0x400 kthread+0x162/0x190 ? set_kthread_struct+0x40/0x40 ret_from_fork+0x22/0x30 </TASK> Also due to this incorrect "nr_running == 1", further queued work may end up not being served, because no worker is awaken at work insert time. This raises rcutorture writer stalls for example. Fix this with disabling preemption in the right place in wq_worker_running(). It's worth noting that if the worker migrates and runs concurrently with unbind_workers(), it is guaranteed to see the WORKER_UNBOUND flag update due to set_cpus_allowed_ptr() acquiring/releasing rq->lock. Fixes: 6d25be5 ("sched/core, workqueues: Distangle worker accounting from rq lock") Reviewed-by: Lai Jiangshan <[email protected]> Tested-by: Paul E. McKenney <[email protected]> Acked-by: Peter Zijlstra (Intel) <[email protected]> Signed-off-by: Frederic Weisbecker <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Sebastian Andrzej Siewior <[email protected]> Cc: Daniel Bristot de Oliveira <[email protected]> Signed-off-by: Tejun Heo <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
[ no upstream commit given implicitly fixed through the larger refactoring in c25b2ae ] While auditing some other code, I noticed missing checks inside the pointer arithmetic simulation, more specifically, adjust_ptr_min_max_vals(). Several *_OR_NULL types are not rejected whereas they are _required_ to be rejected given the expectation is that they get promoted into a 'real' pointer type for the success case, that is, after an explicit != NULL check. One case which stands out and is accessible from unprivileged (iff enabled given disabled by default) is BPF ring buffer. From crafting a PoC, the NULL check can be bypassed through an offset, and its id marking will then lead to promotion of mem_or_null to a mem type. bpf_ringbuf_reserve() helper can trigger this case through passing of reserved flags, for example. func#0 @0 0: R1=ctx(id=0,off=0,imm=0) R10=fp0 0: (7a) *(u64 *)(r10 -8) = 0 1: R1=ctx(id=0,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm 1: (18) r1 = 0x0 3: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm 3: (b7) r2 = 8 4: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R10=fp0 fp-8_w=mmmmmmmm 4: (b7) r3 = 0 5: R1_w=map_ptr(id=0,off=0,ks=0,vs=0,imm=0) R2_w=invP8 R3_w=invP0 R10=fp0 fp-8_w=mmmmmmmm 5: (85) call bpf_ringbuf_reserve#131 6: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 6: (bf) r6 = r0 7: R0_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 7: (07) r0 += 1 8: R0_w=mem_or_null(id=2,ref_obj_id=2,off=1,imm=0) R6_w=mem_or_null(id=2,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 8: (15) if r0 == 0x0 goto pc+4 R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 9: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 9: (62) *(u32 *)(r6 +0) = 0 R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 10: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 10: (bf) r1 = r6 11: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 11: (b7) r2 = 0 12: R0_w=mem(id=0,ref_obj_id=0,off=0,imm=0) R1_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R2_w=invP0 R6_w=mem(id=0,ref_obj_id=2,off=0,imm=0) R10=fp0 fp-8_w=mmmmmmmm refs=2 12: (85) call bpf_ringbuf_submit#132 13: R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm 13: (b7) r0 = 0 14: R0_w=invP0 R6=invP(id=0) R10=fp0 fp-8=mmmmmmmm 14: (95) exit from 8 to 13: safe processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 0 OK All three commits, that is b121b34 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support"), 457f443 ("bpf: Implement BPF ring buffer and verifier support for it"), and the afbf21d ("bpf: Support readonly/readwrite buffers in verifier") suffer the same cause and their *_OR_NULL type pendants must be rejected in adjust_ptr_min_max_vals(). Make the test more robust by reusing reg_type_may_be_null() helper such that we catch all *_OR_NULL types we have today and in future. Note that pointer arithmetic on PTR_TO_BTF_ID, PTR_TO_RDONLY_BUF, and PTR_TO_RDWR_BUF is generally allowed. Fixes: b121b34 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support") Fixes: 457f443 ("bpf: Implement BPF ring buffer and verifier support for it") Fixes: afbf21d ("bpf: Support readonly/readwrite buffers in verifier") Signed-off-by: Daniel Borkmann <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 60c6a63 upstream. Driver should free `usb->setup_packet` to avoid the leak. $ cat /sys/kernel/debug/kmemleak unreferenced object 0xffffffa564a58080 (size 128): backtrace: [<000000007eb8dd70>] kmem_cache_alloc_trace+0x22c/0x384 [<000000008a44191d>] btusb_mtk_hci_wmt_sync+0x1ec/0x994 [btusb] [<00000000ca7189a3>] btusb_mtk_setup+0x6b8/0x13cc [btusb] [<00000000c6105069>] hci_dev_do_open+0x290/0x974 [bluetooth] [<00000000a583f8b8>] hci_power_on+0xdc/0x3cc [bluetooth] [<000000005d80e687>] process_one_work+0x514/0xc80 [<00000000f4d57637>] worker_thread+0x818/0xd0c [<00000000dc7bdb55>] kthread+0x2f8/0x3b8 [<00000000f9999513>] ret_from_fork+0x10/0x30 Fixes: a1c49c4 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Signed-off-by: Mark-YW.Chen <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit d2666be upstream. Add USB IDs (0x10ab, 0x9309) and (0x10ab, 0x9409) to usb_device_id table for WCN6855. * /sys/kernel/debug/usb/devices T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9309 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9409 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 6932627 upstream. Add 2 USB IDs for MT7922A chip. These 2 devices got the same description. T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d8 Rev= 1.00 T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d9 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Aaron Ma <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 1cd563e upstream. Add an ID of Qualcomm Bluetooth SoC WCN6855. T: Bus=05 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d0 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I:* If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Aaron Ma <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit b5e6fa7 upstream. Add the missing bulk-out endpoint sanity check to probe() to avoid division by zero in bfusb_send_frame() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing). Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288 ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")). Cc: [email protected] Signed-off-by: Johan Hovold <[email protected]> Signed-off-by: Marcel Holtmann <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 9cb6de4 upstream. The reset GPIO was marked active-high, which is against what's specified in the documentation. Mark the reset GPIO as active-low. With this change, Bluetooth can now be used on the i9100. Fixes: 8620cc2 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2") Cc: [email protected] Signed-off-by: Paul Cercueil <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Krzysztof Kozlowski <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 0f66372 upstream. Bugzilla #213839 reports a 7-port hub that doesn't work properly when devices are plugged into some of the ports; the kernel goes into an unending disconnect/reinitialize loop as shown in the bug report. This "7-port hub" comprises two four-port hubs with one plugged into the other; the failures occur when a device is plugged into one of the downstream hub's ports. (These hubs have other problems too. For example, they bill themselves as USB-2.0 compliant but they only run at full speed.) It turns out that the failures are caused by bugs in both the kernel and the hub. The hub's bug is that it reports a different bmAttributes value in its configuration descriptor following a remote wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has changed). The kernel's bug is inside the hub driver's resume handler. When hub_activate() sees that one of the hub's downstream ports got a wakeup request from a child device, it notes this fact by setting the corresponding bit in the hub->change_bits variable. But this variable is meant for connection changes, not wakeup events; setting it causes the driver to believe the downstream port has been disconnected and then connected again (in addition to having received a wakeup request). Because of this, the hub driver then tries to check whether the device currently plugged into the downstream port is the same as the device that had been attached there before. Normally this check succeeds and wakeup handling continues with no harm done (which is why the bug remained undetected until now). But with these dodgy hubs, the check fails because the config descriptor has changed. This causes the hub driver to reinitialize the child device, leading to the disconnect/reinitialize loop described in the bug report. The proper way to note reception of a downstream wakeup request is to set a bit in the hub->event_bits variable instead of hub->change_bits. That way the hub driver will realize that something has happened to the port but will not think the port and child device have been disconnected. This patch makes that change. Cc: <[email protected]> Tested-by: Jonathan McDowell <[email protected]> Signed-off-by: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 1d7d4c0 upstream. When the USB core code for getting root-hub status reports was originally written, it was assumed that the hub driver would be its only caller. But this isn't true now; user programs can use usbfs to communicate with root hubs and get status reports. When they do this, they may use a transfer_buffer that is smaller than the data returned by the HCD, which will lead to a buffer overflow error when usb_hcd_poll_rh_status() tries to store the status data. This was discovered by syzbot: BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline] BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776 Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062 This patch fixes the bug by reducing the amount of status data if it won't fit in the transfer_buffer. If some data gets discarded then the URB's completion status is set to -EOVERFLOW rather than 0, to let the user know what happened. Reported-and-tested-by: [email protected] Signed-off-by: Alan Stern <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit a658c92 upstream. If cfg80211 is providing extraie's for a scanning process then ath11k will copy that over to the firmware. The extraie.len is a 32 bit value in struct element_info and describes the amount of bytes for the vendor information elements. The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This section can have a (payload) length up to 65535 bytes because the WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and could have created a scan request which cannot be parsed correctly by the firmware. But the bigger problem was the allocation of the buffer. It has to align the TLV sections by 4 bytes. But the code was using an u8 to store the newly calculated length of this section (with alignment). And the new calculated length was then used to allocate the skbuff. But the actual code to copy in the data is using the extraie.len and not the calculated "aligned" length. The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled was 264 bytes during tests with a QCA Milan card. But it only allocated 8 bytes (264 bytes % 256) for it. As consequence, the code to memcpy the extraie into the skb was then just overwriting data after skb->end. Things like shinfo were therefore corrupted. This could usually be seen by a crash in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus address). Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Cc: [email protected] Fixes: d5c6515 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Sven Eckelmann <[email protected]> Signed-off-by: Kalle Valo <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit e53e97f upstream. Add PCI ID for Intel ADL eMMC host controller. Signed-off-by: Adrian Hunter <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Ulf Hansson <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 710ad98 upstream. Laurent reported that they have seen a significant amount of TCP retransmissions at high throughput from applications residing in network namespaces talking to the outside world via veths. The drops were seen on the qdisc layer (fq_codel, as per systemd default) of the phys device such as ena or virtio_net due to all traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the setup was _not_ using XDP on veths as the issue is generic.) More specifically, after edbea92 ("veth: Store queue_mapping independently of XDP prog presence") which made it all the way back to v4.19.184+, skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX queue by default for veths) instead of leaving at 0. This is eventually retained and callbacks like ena_select_queue() will also pick single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic is forwarded to that device via upper stack or other means. Similarly, for others not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well. In general, it is a _bad_ idea for virtual devices like veth to mess around with queue selection [by default]. Given dev->real_num_tx_queues is by default 1, the skb->queue_mapping was left untouched, and so prior to edbea92 the netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device. Unbreak this and restore prior behavior by removing the skb_record_rx_queue() from veth_xmit() altogether. If the veth peer has an XDP program attached, then it would return the first RX queue index in xdp_md->rx_queue_index (unless configured in non-default manner). However, this is still better than breaking the generic case. Fixes: edbea92 ("veth: Store queue_mapping independently of XDP prog presence") Fixes: 638264d ("veth: Support per queue XDP ring") Reported-by: Laurent Bernaille <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Cc: Maciej Fijalkowski <[email protected]> Cc: Toshiaki Makita <[email protected]> Cc: Eric Dumazet <[email protected]> Cc: Paolo Abeni <[email protected]> Cc: John Fastabend <[email protected]> Cc: Willem de Bruijn <[email protected]> Acked-by: John Fastabend <[email protected]> Reviewed-by: Eric Dumazet <[email protected]> Acked-by: Toshiaki Makita <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit c9e1430 upstream. The runtime PM callback may be called as soon as the runtime PM facility is enabled and activated. It means that ->suspend() may be called before we finish probing the device in the ACPI case. Hence, NULL pointer dereference: intel-lpss INT34BA:00: IRQ index 0 not found BUG: kernel NULL pointer dereference, address: 0000000000000030 ... Workqueue: pm pm_runtime_work RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss] To fix this, first try to register the device and only after that enable runtime PM facility. Fixes: 4b45efe ("mfd: Add support for Intel Sunrisepoint LPSS devices") Reported-by: Orlando Chamberlain <[email protected]> Reported-by: Aditya Garg <[email protected]> Signed-off-by: Andy Shevchenko <[email protected]> Tested-by: Aditya Garg <[email protected]> Signed-off-by: Lee Jones <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
…ption of invalid USB data commit 4a8737f upstream. The received data contains the channel the received data is associated with. If the channel number is bigger than the actual number of channels assume broken or malicious USB device and shut it down. This fixes the error found by clang: | drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used | uninitialized whenever 'if' condition is true | if (hf->channel >= GS_MAX_INTF) | ^~~~~~~~~~~~~~~~~~~~~~~~~~ | drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here | hf, dev->gs_hf_size, gs_usb_receive_bulk_callback, | ^~~ Link: https://lore.kernel.org/all/[email protected] Fixes: d08e973 ("can: gs_usb: Added support for the GS_USB CAN devices") Cc: [email protected] Signed-off-by: Marc Kleine-Budde <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 5f33a09 upstream. In isotp_rcv_ff() 32 bit of data received over the network is assigned to struct tpcon::len. Later in that function the length is checked for the maximal supported length against MAX_MSG_LENGTH. As struct tpcon::len is an "int" this check does not work, if the provided length overflows the "int". Later on struct tpcon::idx is compared against struct tpcon::len. To fix this problem this patch converts both struct tpcon::{idx,len} to unsigned int. Fixes: e057dd3 ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/[email protected] Cc: [email protected] Acked-by: Oliver Hartkopp <[email protected]> Reported-by: [email protected] Signed-off-by: Marc Kleine-Budde <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 89d58ae upstream. No information is deliberately sent in hf->flags in host -> device communications, but the open-source candleLight firmware echoes it back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and generating spurious ERRORFRAMEs. While there also initialize the reserved member with 0. Fixes: d08e973 ("can: gs_usb: Added support for the GS_USB CAN devices") Link: https://lore.kernel.org/all/[email protected] Link: candle-usb/candleLight_fw#87 Cc: [email protected] Signed-off-by: Brian Silverman <[email protected]> [mkl: initialize the reserved member, too] Signed-off-by: Marc Kleine-Budde <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 5d73d1e upstream. extract_crng() and crng_backtrack_protect() load crng_node_pool with a plain load, which causes undefined behavior if do_numa_crng_init() modifies it concurrently. Fix this by using READ_ONCE(). Note: as per the previous discussion https://lore.kernel.org/lkml/[email protected]/T/#u, READ_ONCE() is believed to be sufficient here, and it was requested that it be used here instead of smp_load_acquire(). Also change do_numa_crng_init() to set crng_node_pool using cmpxchg_release() instead of mb() + cmpxchg(), as the former is sufficient here but is more lightweight. Fixes: 1e7f583 ("random: make /dev/urandom scalable for silly userspace programs") Cc: [email protected] Signed-off-by: Eric Biggers <[email protected]> Acked-by: Paul E. McKenney <[email protected]> Signed-off-by: Jason A. Donenfeld <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 009ba85 upstream. _extract_crng() does plain loads of crng->init_time and crng_global_init_time, which causes undefined behavior if crng_reseed() and RNDRESEEDCRNG modify these corrently. Use READ_ONCE() and WRITE_ONCE() to make the behavior defined. Don't fix the race on crng->init_time by protecting it with crng->lock, since it's not a problem for duplicate reseedings to occur. I.e., the lockless access with READ_ONCE() is fine. Fixes: d848e5f ("random: add new ioctl RNDRESEEDCRNG") Fixes: e192be9 ("random: replace non-blocking pool with a Chacha20-based CRNG") Cc: [email protected] Signed-off-by: Eric Biggers <[email protected]> Acked-by: Paul E. McKenney <[email protected]> Signed-off-by: Jason A. Donenfeld <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit f7e67b8 upstream. Currently, if CONFIG_RANDOM_TRUST_BOOTLOADER is enabled, multiple calls to add_bootloader_randomness() are broken and can cause a NULL pointer dereference, as noted by Ivan T. Ivanov. This is not only a hypothetical problem, as qemu on arm64 may provide bootloader entropy via EFI and via devicetree. On the first call to add_hwgenerator_randomness(), crng_fast_load() is executed, and if the seed is long enough, crng_init will be set to 1. On subsequent calls to add_bootloader_randomness() and then to add_hwgenerator_randomness(), crng_fast_load() will be skipped. Instead, wait_event_interruptible() and then credit_entropy_bits() will be called. If the entropy count for that second seed is large enough, that proceeds to crng_reseed(). However, both wait_event_interruptible() and crng_reseed() depends (at least in numa_crng_init()) on workqueues. Therefore, test whether system_wq is already initialized, which is a sufficient indicator that workqueue_init_early() has progressed far enough. If we wind up hitting the !system_wq case, we later want to do what would have been done there when wqs are up, so set a flag, and do that work later from the rand_initialize() call. Reported-by: Ivan T. Ivanov <[email protected]> Fixes: 18b915a ("efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness") Cc: [email protected] Signed-off-by: Dominik Brodowski <[email protected]> [Jason: added crng_need_done state and related logic.] Signed-off-by: Jason A. Donenfeld <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit f66dcb3 upstream. A lot of userspace depends on a descriptive name for vdev. Without this patch, users have a hard time figuring out which camera shall they use for their video conferencing. This reverts commit e3f60e7. Link: https://lore.kernel.org/linux-media/[email protected] Cc: <[email protected]> Fixes: e3f60e7 ("media: uvcvideo: Set unique vdev name based in type") Reported-by: Nicolas Dufresne <[email protected]> Signed-off-by: Ricardo Ribalda <[email protected]> Reviewed-by: Laurent Pinchart <[email protected]> Reviewed-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
…throttlefn() commit 502408a upstream. A new warning in clang points out a place in this file where a bitwise OR is being used with boolean expressions: In file included from drivers/staging/wlan-ng/prism2usb.c:2: drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical] ((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) && ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning 1 warning generated. The comment explains that short circuiting here is undesirable, as the calls to test_and_{clear,set}_bit() need to happen for both sides of the expression. Clang's suggestion would work to silence the warning but the readability of the expression would suffer even more. To clean up the warning and make the block more readable, use a variable for each side of the bitwise expression. Link: ClangBuiltLinux#1478 Signed-off-by: Nathan Chancellor <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 2e70570 upstream. A new warning in clang points out a place in this file where a bitwise OR is being used with boolean types: drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical] changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ This construct is intentional, as it allows every one of the calls to ilk_increase_wm_latency() to occur (instead of short circuiting with logical OR) while still caring about the result of each call. To make this clearer to the compiler, use the '|=' operator to assign the result of each ilk_increase_wm_latency() call to changed, which keeps the meaning of the code the same but makes it obvious that every one of these calls is expected to happen. Link: ClangBuiltLinux#1473 Reported-by: Nick Desaulniers <[email protected]> Signed-off-by: Nathan Chancellor <[email protected]> Suggested-by: Dávid Bolvanský <[email protected]> Reviewed-by: Nick Desaulniers <[email protected]> Signed-off-by: Ville Syrjälä <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
commit 144779e upstream. clang warns about excessive stack usage in this driver when UBSAN is enabled: drivers/staging/greybus/audio_topology.c:977:12: error: stack frame size of 1836 bytes in function 'gbaudio_tplg_create_widget' [-Werror,-Wframe-larger-than=] Rework this code to no longer use compound literals for initializing the structure in each case, but instead keep the common bits in a preallocated constant array and copy them as needed. Link: ClangBuiltLinux#1535 Link: https://lore.kernel.org/r/[email protected]/ Reviewed-by: Nick Desaulniers <[email protected]> Reviewed-by: Alex Elder <[email protected]> Signed-off-by: Arnd Bergmann <[email protected]> [nathan: Address review comments from v1] Signed-off-by: Nathan Chancellor <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
Link: https://lore.kernel.org/r/[email protected] Tested-by: Pavel Machek (CIP) <[email protected]> Tested-by: Jon Hunter <[email protected]> Tested-by: Fox Chen <[email protected]> Tested-by: Florian Fainelli <[email protected]> Tested-by: Shuah Khan <[email protected]> Tested-by: Linux Kernel Functional Testing <[email protected]> Tested-by: Salvatore Bonaccorso <[email protected]> Tested-by: Sudip Mukherjee <[email protected]> Tested-by: Guenter Roeck <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
This is the 5.10.92 stable release Signed-off-by: Andrey Zhizhikin <[email protected]>
zandrey
added a commit
to zandrey/meta-freescale
that referenced
this pull request
Jan 23, 2022
Kernel repository has been upgraded up to v5.10.92 from stable korg.
Following upstream commits are included in this version:
----
c982c1a83932 Linux 5.10.92
c0091233f3d8 staging: greybus: fix stack size warning with UBSAN
66d21c005d9b drm/i915: Avoid bitwise vs logical OR warning in snb_wm_latency_quirk()
2d4fda471dc3 staging: wlan-ng: Avoid bitwise vs logical OR warning in hfa384x_usb_throttlefn()
3609fed7ac8b media: Revert "media: uvcvideo: Set unique vdev name based in type"
9b3c761e78d5 random: fix crash on multiple early calls to add_bootloader_randomness()
61cca7d191c7 random: fix data race on crng init time
3de9478230c3 random: fix data race on crng_node_pool
43c494294f30 can: gs_usb: gs_can_start_xmit(): zero-initialize hf->{flags,reserved}
45221a57b609 can: isotp: convert struct tpcon::{idx,len} to unsigned int
bd61ae808b15 can: gs_usb: fix use of uninitialized variable, detach device on reception of invalid USB data
f68e60001735 mfd: intel-lpss: Fix too early PM enablement in the ACPI ->probe()
5f76445a31b7 veth: Do not record rx queue hint in veth_xmit
ddfa53825f3d mmc: sdhci-pci: Add PCI ID for Intel ADL
2e691f9894cc ath11k: Fix buffer overflow when scanning with extraie
a87cecf94375 USB: Fix "slab-out-of-bounds Write" bug in usb_hcd_poll_rh_status
15982330b61d USB: core: Fix bug in resuming hub's handling of wakeup requests
413108ce3b56 ARM: dts: exynos: Fix BCM4330 Bluetooth reset polarity in I9100
b6dd07023699 Bluetooth: bfusb: fix division by zero in send path
869e1677a058 Bluetooth: btusb: Add support for Foxconn QCA 0xe0d0
c20021ce945f Bluetooth: btusb: Add support for Foxconn MT7922A
83493918380f Bluetooth: btusb: Add two more Bluetooth parts for WCN6855
294c0dd80d8a Bluetooth: btusb: fix memory leak in btusb_mtk_submit_wmt_recv_urb()
35ab8c9085b0 bpf: Fix out of bounds access from invalid *_or_null type verification
c84fbba8a945 workqueue: Fix unbind_workers() VS wq_worker_running() race
c39d68ab3836 md: revert io stats accounting
----
Link: https://lore.kernel.org/r/[email protected] # v5.10.92
Link: Freescale/linux-fslc#524
Signed-off-by: Andrey Zhizhikin <[email protected]>
zandrey
pushed a commit
to zandrey/linux-fslc
that referenced
this pull request
Jun 9, 2022
[ Upstream commit df5cd36 ] When we boot a machine using a devicetree, the generic DT code goes through all nodes with a 'device_type = "memory"' property, and collects all memory banks mentioned there. However it does not check for the status property, so any nodes which are explicitly "disabled" will still be added as a memblock. This ends up badly for QEMU, when booting with secure firmware on arm/arm64 machines, because QEMU adds a node describing secure-only memory: =================== secram@e000000 { secure-status = "okay"; status = "disabled"; reg = <0x00 0xe000000 0x00 0x1000000>; device_type = "memory"; }; =================== The kernel will eventually use that memory block (which is located below the main DRAM bank), but accesses to that will be answered with an SError: =================== [ 0.000000] Internal error: synchronous external abort: 96000050 [Freescale#1] PREEMPT SMP [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc6-00014-g10c8acb8b679 Freescale#524 [ 0.000000] Hardware name: linux,dummy-virt (DT) [ 0.000000] pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 0.000000] pc : new_slab+0x190/0x340 [ 0.000000] lr : new_slab+0x184/0x340 [ 0.000000] sp : ffff80000a4b3d10 .... ================== The actual crash location and call stack will be somewhat random, and depend on the specific allocation of that physical memory range. As the DT spec[1] explicitly mentions standard properties, add a simple check to skip over disabled memory nodes, so that we only use memory that is meant for non-secure code to use. That fixes booting a QEMU arm64 VM with EL3 enabled ("secure=on"), when not using UEFI. In this case the QEMU generated DT will be handed on to the kernel, which will see the secram node. This issue is reproducible when using TF-A together with U-Boot as firmware, then booting with the "booti" command. When using U-Boot as an UEFI provider, the code there [2] explicitly filters for disabled nodes when generating the UEFI memory map, so we are safe. EDK/2 only reads the first bank of the first DT memory node [3] to learn about memory, so we got lucky there. [1] https://github.com/devicetree-org/devicetree-specification/blob/main/source/chapter3-devicenodes.rst#memory-node (after the table) [2] https://source.denx.de/u-boot/u-boot/-/blob/master/lib/fdtdec.c#L1061-1063 [3] https://github.com/tianocore/edk2/blob/master/ArmVirtPkg/PrePi/FdtParser.c Reported-by: Ross Burton <[email protected]> Signed-off-by: Andre Przywara <[email protected]> Signed-off-by: Rob Herring <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Sasha Levin <[email protected]>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Automatic merge performed, no conflicts reported.
Kernel has been built for aarch64 (
defconfig).-- andrey