Merge pull request #598 from zandrey/5.15.x+fslc

Update 5.15.x+fslc up to v5.15.63

Documentation/ABI/testing/sysfs-bus-iio-vf610

@@ -1,4 +1,4 @@
-What:		/sys/bus/iio/devices/iio:deviceX/conversion_mode
+What:		/sys/bus/iio/devices/iio:deviceX/in_conversion_mode
 KernelVersion:	4.2
 Contact:	[email protected]
 Description:

Documentation/ABI/testing/sysfs-driver-xen-blkback

@@ -42,5 +42,5 @@ KernelVersion:  5.10
 Contact:        SeongJae Park <[email protected]>
 Description:
                 Whether to enable the persistent grants feature or not.  Note
-                that this option only takes effect on newly created backends.
+                that this option only takes effect on newly connected backends.
                 The default is Y (enable).

Documentation/ABI/testing/sysfs-driver-xen-blkfront

@@ -15,5 +15,5 @@ KernelVersion:  5.10
 Contact:        SeongJae Park <[email protected]>
 Description:
                 Whether to enable the persistent grants feature or not.  Note
-                that this option only takes effect on newly created frontends.
+                that this option only takes effect on newly connected frontends.
                 The default is Y (enable).

Documentation/admin-guide/device-mapper/writecache.rst

@@ -78,16 +78,16 @@ Status:
 2. the number of blocks
 3. the number of free blocks
 4. the number of blocks under writeback
-5. the number of read requests
-6. the number of read requests that hit the cache
-7. the number of write requests
-8. the number of write requests that hit uncommitted block
-9. the number of write requests that hit committed block
-10. the number of write requests that bypass the cache
-11. the number of write requests that are allocated in the cache
+5. the number of read blocks
+6. the number of read blocks that hit the cache
+7. the number of write blocks
+8. the number of write blocks that hit uncommitted block
+9. the number of write blocks that hit committed block
+10. the number of write blocks that bypass the cache
+11. the number of write blocks that are allocated in the cache
 12. the number of write requests that are blocked on the freelist
 13. the number of flush requests
-14. the number of discard requests
+14. the number of discarded blocks
 
 Messages:
 	flush

Documentation/admin-guide/hw-vuln/spectre.rst

@@ -422,6 +422,14 @@ The possible values in this file are:
   'RSB filling'   Protection of RSB on context switch enabled
   =============   ===========================================
 
+  - EIBRS Post-barrier Return Stack Buffer (PBRSB) protection status:
+
+  ===========================  =======================================================
+  'PBRSB-eIBRS: SW sequence'   CPU is affected and protection of RSB on VMEXIT enabled
+  'PBRSB-eIBRS: Vulnerable'    CPU is vulnerable
+  'PBRSB-eIBRS: Not affected'  CPU is not affected by PBRSB
+  ===========================  =======================================================
+
 Full mitigation might require a microcode update from the CPU
 vendor. When the necessary microcode is not available, the kernel will
 report vulnerability.

Documentation/admin-guide/kernel-parameters.txt

@@ -3020,6 +3020,7 @@
 					       no_entry_flush [PPC]
 					       no_uaccess_flush [PPC]
 					       mmio_stale_data=off [X86]
+					       retbleed=off [X86]
 
 				Exceptions:
 					       This does not have any effect on
@@ -3042,6 +3043,7 @@
 					       mds=full,nosmt [X86]
 					       tsx_async_abort=full,nosmt [X86]
 					       mmio_stale_data=full,nosmt [X86]
+					       retbleed=auto,nosmt [X86]
 
 	mminit_loglevel=
 			[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
@@ -4968,6 +4970,43 @@
 
 	retain_initrd	[RAM] Keep initrd memory after extraction
 
+	retbleed=	[X86] Control mitigation of RETBleed (Arbitrary
+			Speculative Code Execution with Return Instructions)
+			vulnerability.
+
+			AMD-based UNRET and IBPB mitigations alone do not stop
+			sibling threads from influencing the predictions of other
+			sibling threads. For that reason, STIBP is used on pro-
+			cessors that support it, and mitigate SMT on processors
+			that don't.
+
+			off          - no mitigation
+			auto         - automatically select a migitation
+			auto,nosmt   - automatically select a mitigation,
+				       disabling SMT if necessary for
+				       the full mitigation (only on Zen1
+				       and older without STIBP).
+			ibpb         - On AMD, mitigate short speculation
+				       windows on basic block boundaries too.
+				       Safe, highest perf impact. It also
+				       enables STIBP if present. Not suitable
+				       on Intel.
+			ibpb,nosmt   - Like "ibpb" above but will disable SMT
+				       when STIBP is not available. This is
+				       the alternative for systems which do not
+				       have STIBP.
+			unret        - Force enable untrained return thunks,
+				       only effective on AMD f15h-f17h based
+				       systems.
+			unret,nosmt  - Like unret, but will disable SMT when STIBP
+				       is not available. This is the alternative for
+				       systems which do not have STIBP.
+
+			Selecting 'auto' will choose a mitigation method at run
+			time according to the CPU.
+
+			Not specifying this option is equivalent to retbleed=auto.
+
 	rfkill.default_state=
 		0	"airplane mode".  All wifi, bluetooth, wimax, gps, fm,
 			etc. communication is blocked by default.
@@ -5314,6 +5353,7 @@
 			eibrs		  - enhanced IBRS
 			eibrs,retpoline   - enhanced IBRS + Retpolines
 			eibrs,lfence      - enhanced IBRS + LFENCE
+			ibrs		  - use IBRS to protect kernel
 
 			Not specifying this option is equivalent to
 			spectre_v2=auto.

Documentation/admin-guide/pm/cpuidle.rst

@@ -612,8 +612,8 @@ the ``menu`` governor to be used on the systems that use the ``ladder`` governor
 by default this way, for example.
 
 The other kernel command line parameters controlling CPU idle time management
-described below are only relevant for the *x86* architecture and some of
-them affect Intel processors only.
+described below are only relevant for the *x86* architecture and references
+to ``intel_idle`` affect Intel processors only.
 
 The *x86* architecture support code recognizes three kernel command line
 options related to CPU idle time management: ``idle=poll``, ``idle=halt``,
@@ -635,10 +635,13 @@ idle, so it very well may hurt single-thread computations performance as well as
 energy-efficiency.  Thus using it for performance reasons may not be a good idea
 at all.]
 
-The ``idle=nomwait`` option disables the ``intel_idle`` driver and causes
-``acpi_idle`` to be used (as long as all of the information needed by it is
-there in the system's ACPI tables), but it is not allowed to use the
-``MWAIT`` instruction of the CPUs to ask the hardware to enter idle states.
+The ``idle=nomwait`` option prevents the use of ``MWAIT`` instruction of
+the CPU to enter idle states. When this option is used, the ``acpi_idle``
+driver will use the ``HLT`` instruction instead of ``MWAIT``. On systems
+running Intel processors, this option disables the ``intel_idle`` driver
+and forces the use of the ``acpi_idle`` driver instead. Note that in either
+case, ``acpi_idle`` driver will function only if all the information needed
+by it is in the system's ACPI tables.
 
 In addition to the architecture-level kernel command line options affecting CPU
 idle time management, there are parameters affecting individual ``CPUIdle``

Documentation/admin-guide/sysctl/vm.rst

@@ -948,7 +948,7 @@ how much memory needs to be free before kswapd goes back to sleep.
 
 The unit is in fractions of 10,000. The default value of 10 means the
 distances between watermarks are 0.1% of the available memory in the
-node/system. The maximum value is 1000, or 10% of memory.
+node/system. The maximum value is 3000, or 30% of memory.
 
 A high rate of threads entering direct reclaim (allocstall) or kswapd
 going to sleep prematurely (kswapd_low_wmark_hit_quickly) can indicate

Documentation/atomic_bitops.txt

@@ -59,7 +59,7 @@ Like with atomic_t, the rule of thumb is:
  - RMW operations that have a return value are fully ordered.
 
  - RMW operations that are conditional are unordered on FAILURE,
-   otherwise the above rules apply. In the case of test_and_{}_bit() operations,
+   otherwise the above rules apply. In the case of test_and_set_bit_lock(),
    if the bit in memory is unchanged by the operation then it is deemed to have
    failed.
 

Documentation/devicetree/bindings/arm/qcom.yaml

@@ -135,28 +135,34 @@ properties:
           - const: qcom,msm8974
 
       - items:
-          - enum:
-              - alcatel,idol347
-          - const: qcom,msm8916-mtp/1
           - const: qcom,msm8916-mtp
+          - const: qcom,msm8916-mtp/1
           - const: qcom,msm8916
 
       - items:
           - enum:
-              - longcheer,l8150
+              - alcatel,idol347
               - samsung,a3u-eur
               - samsung,a5u-eur
           - const: qcom,msm8916
 
+      - items:
+          - const: longcheer,l8150
+          - const: qcom,msm8916-v1-qrd/9-v1
+          - const: qcom,msm8916
+
       - items:
           - enum:
               - sony,karin_windy
+          - const: qcom,apq8094
+
+      - items:
+          - enum:
               - sony,karin-row
               - sony,satsuki-row
               - sony,sumire-row
               - sony,suzuran-row
-              - qcom,msm8994
-          - const: qcom,apq8094
+          - const: qcom,msm8994
 
       - items:
           - const: qcom,msm8996-mtp

Documentation/devicetree/bindings/clock/qcom,gcc-msm8996.yaml

@@ -22,16 +22,32 @@ properties:
     const: qcom,gcc-msm8996
 
   clocks:
+    minItems: 3
     items:
       - description: XO source
       - description: Second XO source
       - description: Sleep clock source
+      - description: PCIe 0 PIPE clock (optional)
+      - description: PCIe 1 PIPE clock (optional)
+      - description: PCIe 2 PIPE clock (optional)
+      - description: USB3 PIPE clock (optional)
+      - description: UFS RX symbol 0 clock (optional)
+      - description: UFS RX symbol 1 clock (optional)
+      - description: UFS TX symbol 0 clock (optional)
 
   clock-names:
+    minItems: 3
     items:
       - const: cxo
       - const: cxo2
       - const: sleep_clk
+      - const: pcie_0_pipe_clk_src
+      - const: pcie_1_pipe_clk_src
+      - const: pcie_2_pipe_clk_src
+      - const: usb3_phy_pipe_clk_src
+      - const: ufs_rx_symbol_0_clk_src
+      - const: ufs_rx_symbol_1_clk_src
+      - const: ufs_tx_symbol_0_clk_src
 
   '#clock-cells':
     const: 1

Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml

@@ -64,7 +64,7 @@ if:
 then:
   properties:
     clocks:
-      maxItems: 2
+      minItems: 2
 
   required:
     - clock-names

Documentation/devicetree/bindings/gpio/gpio-zynq.yaml

@@ -11,7 +11,11 @@ maintainers:
 
 properties:
   compatible:
-    const: xlnx,zynq-gpio-1.0
+    enum:
+      - xlnx,zynq-gpio-1.0
+      - xlnx,zynqmp-gpio-1.0
+      - xlnx,versal-gpio-1.0
+      - xlnx,pmc-gpio-1.0
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml

@@ -0,0 +1,88 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/accel/adi,adxl355.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADXL355 3-Axis, Low noise MEMS Accelerometer
+
+maintainers:
+  - Puranjay Mohan <[email protected]>
+
+description: |
+  Analog Devices ADXL355 3-Axis, Low noise MEMS Accelerometer that supports
+  both I2C & SPI interfaces
+    https://www.analog.com/en/products/adxl355.html
+
+properties:
+  compatible:
+    enum:
+      - adi,adxl355
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 1
+    maxItems: 3
+    description: |
+      Type for DRDY should be IRQ_TYPE_EDGE_RISING.
+      Three configurable interrupt lines exist.
+
+  interrupt-names:
+    description: Specify which interrupt line is in use.
+    items:
+      enum:
+        - INT1
+        - INT2
+        - DRDY
+    minItems: 1
+    maxItems: 3
+
+  vdd-supply:
+    description: Regulator that provides power to the sensor
+
+  vddio-supply:
+    description: Regulator that provides power to the bus
+
+  spi-max-frequency: true
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+        #include <dt-bindings/gpio/gpio.h>
+        #include <dt-bindings/interrupt-controller/irq.h>
+        i2c {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                /* Example for a I2C device node */
+                accelerometer@1d {
+                        compatible = "adi,adxl355";
+                        reg = <0x1d>;
+                        interrupt-parent = <&gpio>;
+                        interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+                        interrupt-names = "DRDY";
+                };
+        };
+  - |
+        #include <dt-bindings/gpio/gpio.h>
+        #include <dt-bindings/interrupt-controller/irq.h>
+        spi {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                accelerometer@0 {
+                        compatible = "adi,adxl355";
+                        reg = <0>;
+                        spi-max-frequency = <1000000>;
+                        interrupt-parent = <&gpio>;
+                        interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+                        interrupt-names = "DRDY";
+                };
+        };

Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml

@@ -23,6 +23,7 @@ properties:
       - brcm,bcm4345c5
       - brcm,bcm43540-bt
       - brcm,bcm4335a0
+      - brcm,bcm4349-bt
 
   shutdown-gpios:
     maxItems: 1

Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml

@@ -47,12 +47,6 @@ properties:
         description:
           Properties for single LDO regulator.
 
-        properties:
-          regulator-name:
-            pattern: "^LDO[1-5]$"
-            description:
-              should be "LDO1", ..., "LDO5"
-
         unevaluatedProperties: false
 
       "^BUCK[1-6]$":
@@ -62,11 +56,6 @@ properties:
           Properties for single BUCK regulator.
 
         properties:
-          regulator-name:
-            pattern: "^BUCK[1-6]$"
-            description:
-              should be "BUCK1", ..., "BUCK6"
-
           nxp,dvs-run-voltage:
             $ref: "/schemas/types.yaml#/definitions/uint32"
             minimum: 600000