ThroughLoRa

ThroughLoRa

Medium	Pins used	Inclusion
LoRa radio	6	#include <PJONThroughLora.h>

With ThroughLora strategy, PJON can run through a software or hardware SPI in order to communicate with supported LoRa modules. See Supported Shields/Modules.

This strategy is a wrapper around Arduino LoRa library created by Sandeep Mistry so all the credit to the specific LoRa implementation goes to him.

Compatibility

• ATmega88/168/328 16MHz (Diecimila, Duemilanove, Uno, Nano, Mini, Lillypad)
• ATmega2560 16MHz (Arduino Mega)
• ATmega16u4/32u4 16MHz (Arduino Leonardo)
• STM32F103 (Blue Pill)

Getting started

1. Pass the ThroughLora type as PJON template parameter to instantiate a PJON object ready to communicate through this Strategy.
2. Configure the shield/module pins according to the correct connection. See Hardware connection.
3. Initialize the module with its specified frequency.

#include <PJONThroughLora.h>

PJONThroughLora bus; //PJON Lora bus instance

bus.strategy.setPins(10,9,2); //CS pin, Reset pin, Interrupt pin
bus.strategy.setFrequency(868100000UL); //initialize 868 MHZ module

Supported Shields/Modules

Manufacturer	Hardware
Dragino	Dragino Lora Shield
HopeRF	RFM95W / RFM96W / RFM98W
Modtronix	inAir4 / inAir9 / inAir9B
Adafruit	Adafruit Feather 32u4 LoRa Radio (RFM9x)

Hardware connection

General Wiring	Arduino
VCC	3.3V
GND	GND
SCK	SCK
MISO	MISO
MOSI	MOSI
NSS	10
NRESET	9
DIO0	2

• NSS, NRESET, and DIO0 pins can be changed by using PJON.strategy.setPins(ss, reset, dio0).
• DIO0 pin is optional, it is only needed for receive callback mode. If DIO0 pin is used, it must be interrupt capable via attachInterrupt(...).

Usage Example

Here are listed basic examples of a transmitter and receiver code. After you include the necessary code to initialize the Lora module you can use the normal PJON functions to handle data communication.

Keep in mind that to use the LoRa startegy you must download the Arduino LoRa library.

More examples can be found in https://github.com/gioblu/PJON/tree/master/examples/ARDUINO/Local/ThroughLoRa

Transmitter

#include <PJONThroughLora.h>

PJONThroughLora bus(45);

void setup() {
  // Obligatory to initialize Radio with correct frequency
  bus.strategy.setFrequency(868100000UL);
  bus.begin();
  // Send B to device 44 every second
  bus.send_repeatedly(44, "B", 1, 1000000);
};

void loop() {
  bus.update();
};

Receiver

#include <PJONThroughLora.h>

// <Strategy name> bus(selected device id)
PJONThroughLora bus(44);

void setup() {
  pinMode(13, OUTPUT);
  digitalWrite(13, LOW); // Initialize LED 13 to be off
  Serial.begin(9600);

  // Obligatory to initialize Radio with correct frequency
  bus.strategy.setFrequency(868100000UL);
  // Optional
  bus.strategy.setSignalBandwidth(250E3);
  bus.begin();
  bus.set_receiver(receiver_function);
};

void receiver_function(uint8_t *payload, uint16_t length, const PJON_Packet_Info &packet_info) {
  /* Make use of the payload before sending something, the buffer where payload points to is
     overwritten when a new message is dispatched */
 if (payload[0] == 'B') {
    digitalWrite(13, HIGH);
    delay(30);
    digitalWrite(13, LOW);
  }
};

void loop() {
  bus.receive(1000);
};

This API is a specific wrapper around the Arduino-LoRa library

All the LoRa API is accessible through the exposed strategy in a PJON instance. Ex: bus.strategy

Setup

Initialize the library with the specified frequency.

bus.strategy.setFrequency(frequency);

• frequency - frequency in Hz (433E6, 866E6, 915E6)

Returns 1 on success, 0 on failure.

Set pins

Override the default NSS, NRESET, and DIO0 pins used by the library. Must be called before LoRa.begin().

bus.strategy.setPins(ss, reset, dio0);

• ss - new slave select pin to use, defaults to 10
• reset - new reset pin to use, defaults to 9
• dio0 - new DIO0 pin to use, defaults to 2, must be interrupt capable via attachInterrupt(...).

This call is optional and only needs to be used if you need to change the default pins used.

Configuration

int rssi = bus.strategy.packetRssi();

Returns the RSSI of the received packet.

float snr = bus.strategy.packetSnr();

Returns the estimated SNR of the received packet in dB.

bus.strategy.setSignalBandwidth(signalBandwidth);

Change the signal bandwidth of the radio, signalBandwidth represents the signal bandwidth in Hz, defaults to 125E3. Supported values are 7.8E3, 10.4E3, 15.6E3, 20.8E3, 31.25E3, 41.7E3, 62.5E3, 125E3, and 250E3.

bus.strategy.setSpreadingFactor(spreadingFactor);

Change the spreading factor of the radio. spreadingFactor represents the spreading factor, defaults to 7. Supported values are between 6 and 12. If a spreading factor of 6 is set, implicit header mode must be used to transmit and receive packets.

bus.strategy.setCodingRate4(codingRateDenominator);

Change the coding rate of the radio. codingRateDenominator represents denominator of the coding rate, defaults to 5. Supported values are between 5 and 8, these correspond to coding rates of 4/5 and 4/8. The coding rate numerator is fixed at 4.

bus.strategy.setPreambleLength(preambleLength);

Change the preamble length of the radio. preambleLength represents preamble length in symbols, defaults to 8. Supported values are between 6 and 65535.

bus.strategy.setSyncWord(syncWord);

Change the sync word of the radio. syncWord represents byte value to use as the sync word, defaults to 0x34

bus.strategy.setCRC(false); //To disable CRC
bus.strategy.setCRC(true); // To enable CRC

Enable or disable CRC usage, by default a CRC is not used.

LoRa.setTxPower(txPower); //Configure the radio TX power

LoRa.setTxPower(txPower, outputPin); //Configure the radio TX power with extra boost pin

Change the TX power of the radio.

• txPower - TX power in dB, defaults to 17
• outputPin - (optional) PA output pin, supported values are PA_OUTPUT_RFO_PIN and PA_OUTPUT_PA_BOOST_PIN, defaults to PA_OUTPUT_PA_BOOST_PIN.

Supported values are between 2 and 17 for PA_OUTPUT_PA_BOOST_PIN, 0 and 14 for PA_OUTPUT_RFO_PIN.

Most modules have the PA output pin connected to PA BOOST.

bus.strategy.idle();

Put the radio in idle (standby) mode.

bus.strategy.sleep();

Put the radio in sleep mode.

byte b = bus.strategy.getRandom();

Generate a random byte, based on the Wideband RSSI measurement.

Safety warning

In all cases, when installing or maintaining a PJON network, extreme care must be taken to avoid any danger. Before any practical test or hardware purchase for a wireless ThroughLoRa radio setup, compliance with government requirements and regulations must be ensured.