-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathrobin_nano35_cfg.txt
285 lines (215 loc) · 6.96 KB
/
robin_nano35_cfg.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
#==========================================================
>cfg_insert_det_module 0
>cfg_have_ups_device 0
>cfg_print_over_auto_close 1
>cfg_filament_det0_trigger_level 0
>cfg_filament_det1_trigger_level 0
>cfg_filament_load_length 100
>cfg_filament_load_speed 2300
>cfg_filament_load_limit_temperature 190
>cfg_filament_unload_length 100
>cfg_filament_unload_speed 2300
>cfg_filament_unload_limit_temperature 190
#========================================================
>cfg_leveling_mode 0
#=============================================================
>cfg_point_number 4
>cfg_point1:30,30
>cfg_point2:235,30
>cfg_point3:235,190
>cfg_point4:30,190
>cfg_point5:100,100
#========================== ===================================
>cfg_auto_leveling_cmd:G28;G29;
#=============================================================
>cfg_language_adjust_type 1
>cfg_language_type 2
#===================================================
>setmenu_func1_display 1
>setmenu_func1:M84;
>moreitem_pic_cnt 7
>moreitem_button1_cmd:G28 X0;G28 Y0;G28 Z0;
>moreitem_button2_cmd:G28 X0;G28 Y0;G28 Z0;
>moreitem_button3_cmd:G28 X0;G28 Y0;G28 Z0;
>moreitem_button4_cmd:G28 X0;G28 Y0;G28 Z0;
>moreitem_button5_cmd:G28 X0;G28 Y0;G28 Z0;
>moreitem_button6_cmd:G28 X0;G28 Y0;G28 Z0;
>moreitem_button7_cmd:G28 X0;G28 Y0;G28 Z0;
>morefunc_cnt 7
>morefunc1_cmd:G28;
>morefunc2_cmd:G28;
>morefunc3_cmd:G28;
>morefunc4_cmd:G28;
>morefunc5_cmd:G28;
>morefunc6_cmd:G28;
>morefunc7_cmd:G28;
#-------------------------------------------------------------
>cfg_background_color 0xFFFFFF
>cfg_title_color 0xFFFFFF
>cfg_state_bkcolor 0xFFFFFF
>cfg_state_textcolor 0x000000
>cfg_filename_bkcolor 0xffffff
>cfg_filename_textcolor 0x000000
>cfg_btn_bkcolor 0xFFFFFF
>cfg_btn_textcolor 0xFFFFFF
>cfg_state_btn_bkcolor 0xffffff
>cfg_state_btn_textcolor 0x000000
>cfg_back_btn_bkcolor 0x000000
>cfg_back_btn_textcolor 0xFFFFFF
>cfg_sel_btn_bkcolor 0x000000
>cfg_sel_btn_textcolor 0xFFFFFF
>cfg_dialog_btn_bkcolor 0xff0000
>cfg_dialog_btn_textcolor 0xFFFFFF
>cfg_btn_text_offset 10
>cfg_screen_display_mode 0
>cfg_screen_overturn_180 0x00
#======================================================
>MACHINETPYE 0
>HAS_TEMP_BED 1
>EXTRUDERS 1
>Z2_STEPPER_DRIVERS 0
>Z2_ENDSTOPS 0
>Z2_USE_ENDSTOP 0
# XYZ
>X_MIN_POS 0
>Y_MIN_POS 0
>Z_MIN_POS 0
>X_MAX_POS 255
>Y_MAX_POS 210
>Z_MAX_POS 210
>FILAMENT_CHANGE_X_POS 5
>FILAMENT_CHANGE_Y_POS 5
>FILAMENT_CHANGE_Z_ADD 5
>HOTEND_OFFSET_X 20.00
>HOTEND_OFFSET_Y 5.00
#==========================================================
>INVERT_X_DIR 0
>INVERT_Y_DIR 0
>INVERT_Z_DIR 1
>INVERT_E0_DIR 1
>INVERT_E1_DIR 1
>DEFAULT_X_STEPS_PER_UNIT 80
>DEFAULT_Y_STEPS_PER_UNIT 80
>DEFAULT_Z_STEPS_PER_UNIT 400
>DEFAULT_E0_STEPS_PER_UNIT 400
>DEFAULT_E1_STEPS_PER_UNIT 90
>DEFAULT_X_MAX_FEEDRATE 300
>DEFAULT_Y_MAX_FEEDRATE 300
>DEFAULT_Z_MAX_FEEDRATE 5
>DEFAULT_E0_MAX_FEEDRATE 70
>DEFAULT_E1_MAX_FEEDRATE 70
>DEFAULT_X_MAX_ACCELERATION 1500
>DEFAULT_Y_MAX_ACCELERATION 1500
>DEFAULT_Z_MAX_ACCELERATION 200
>DEFAULT_E0_MAX_ACCELERATION 10000
>DEFAULT_E1_MAX_ACCELERATION 10000
>DEFAULT_ACCELERATION 1500
>DEFAULT_RETRACT_ACCELERATION 10000
>DEFAULT_TRAVEL_ACCELERATION 1500
>DEFAULT_MINIMUMFEEDRATE 0.0
>DEFAULT_MINSEGMENTTIME 10000
>DEFAULT_MINTRAVELFEEDRATE 0.0
>DEFAULT_XJERK 12.0
>DEFAULT_YJERK 12.0
>DEFAULT_ZJERK 0.4
>DEFAULT_EJERK 5.0
#For Inverting Stepper Enable Pins (0:Low,1:High)
>X_ENABLE_ON 0
>Y_ENABLE_ON 0
>Z_ENABLE_ON 0
>E_ENABLE_ON 0
#=========================================================
>TEMP_SENSOR_0 1
>EXTRUDE_MINTEMP 160
>HEATER_0_MINTEMP -5
>HEATER_0_MAXTEMP 350
>HEATER_1_MINTEMP -5
>HEATER_1_MAXTEMP 400
>BED_MAXTEMP 150
#===============================================
>THERMAL_PROTECTION_PERIOD 150
>THERMAL_PROTECTION_HYSTERESIS 6
>WATCH_TEMP_PERIOD 150
>WATCH_TEMP_INCREASE 2
>THERMAL_PROTECTION_BED_PERIOD 200
>THERMAL_PROTECTION_BED_HYSTERESIS 4
>WATCH_BED_TEMP_PERIOD 200
>WATCH_BED_TEMP_INCREASE 2
>PIDTEMPE 1
>DEFAULT_Kp 11.14
>DEFAULT_Ki 0.72
>DEFAULT_Kd 43.09
>PIDTEMPBED 1
>DEFAULT_bedKp 52.63
>DEFAULT_bedKi 9.75
>DEFAULT_bedKd 71.01
#=========================================================
>MIN_SOFTWARE_ENDSTOPS 1
>MAX_SOFTWARE_ENDSTOPS 1
>X_MIN_ENDSTOP_INVERTING 1
>Y_MIN_ENDSTOP_INVERTING 1
>Z_MIN_ENDSTOP_INVERTING 1
>X_MAX_ENDSTOP_INVERTING 1
>Y_MAX_ENDSTOP_INVERTING 1
>Z_MAX_ENDSTOP_INVERTING 1
>FIL_RUNOUT_INVERTING 0
>USE_XMIN_PLUG 1
>USE_YMIN_PLUG 1
>USE_ZMIN_PLUG 1
>USE_XMAX_PLUG 0
>USE_YMAX_PLUG 0
>USE_ZMAX_PLUG 1
#============================================================
>X_HOME_DIR -1
>Y_HOME_DIR -1
>Z_HOME_DIR -1
>HOMING_FEEDRATE_XY 2400
>HOMING_FEEDRATE_Z 600
>HOME_Y_BEFORE_X 0
#==========================================================
>Z_MIN_PROBE_PIN_MODE 0
>Z_PROBE_OFFSET_FROM_EXTRUDER 0
>X_PROBE_OFFSET_FROM_EXTRUDER 0
>Y_PROBE_OFFSET_FROM_EXTRUDER 0
>XY_PROBE_SPEED 4000
>Z_PROBE_SPEED_FAST 600
>Z_PROBE_SPEED_SLOW 300
#=============================================================
>BED_LEVELING_METHOD 0
>GRID_MAX_POINTS_X 3
>GRID_MAX_POINTS_Y 3
>Z_CLEARANCE_DEPLOY_PROBE 20
>Z_CLEARANCE_BETWEEN_PROBES 20
>LEFT_PROBE_BED_POSITION 30
>RIGHT_PROBE_BED_POSITION 180
>FRONT_PROBE_BED_POSITION 30
>BACK_PROBE_BED_POSITION 180
>MESH_INSET 20
#============================== Delta =============================
>DELTA_SEGMENTS_PER_SECOND 40 #--default
>DELTA_DIAGONAL_ROD 346.75 #Center-to-center distance of the holes in the diagonal push rods.
>DELTA_SMOOTH_ROD_OFFSET 211.5 #Horizontal offset from middle of printer to smooth rod center.
>DELTA_EFFECTOR_OFFSET 28 #Horizontal offset of the universal joints on the end effector.
>DELTA_CARRIAGE_OFFSET 14.5 #Horizontal offset of the universal joints on the carriages.
>DELTA_RADIUS 169 #Horizontal distance bridged by diagonal push rods when effector is centered.
>DELTA_HEIGHT 302 #height from z=0.00 to home position
>DELTA_PRINTABLE_RADIUS 125 #Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
>DELTA_CALIBRATION_RADIUS 100 #set the radius for the calibration probe points - max 0.8 * DELTA_PRINTABLE_RADIUS
#============================== Wifi ���� =============================
>CFG_WIFI_MODE 0
>CFG_WIFI_AP_NAME
>CFG_WIFI_KEY_CODE
>CFG_CLOUD_ENABLE 0
>CFG_WIFI_CLOUD_HOST
>CFG_CLOUD_PORT
>WISI_LIST_SCAN 1
>about_type:V71-T2225
>about_version:V71-T2225
>about_company:[email protected]
>about_email:[email protected]
>TOUCH_ADJUST_DEFAULT 0
>KEY_VOICE 1
>HOME_X_OFFSET 0.1
>HOME_Y_OFFSET 0
>HOME_Z_OFFSET 0
>THERMAL_NUM 0