-
Notifications
You must be signed in to change notification settings - Fork 1.6k
Validating on PoC 2
This guide follows Validating on PoC-1. The following information has been updated to match version 0.2.1, released August 31st 2018.
Being a validator on the Polkadot network is simple but there are a few caveats and you need to make it right to ensure your validator will behave itself and earn youDOTs.
First of all, validators are the heart of the network: they validate new blocks in a similar way Bitcoin miners create new blocks on the Bitcoin blockchain. Polkadot however is not based on Proof Of Work. Validators do not need high performance computers but they need to met a few conditions.
As a validator, you may earn testnet DOTs when following the rules and keeping your node up and running. For this reason, the choice of the computer running your node is important and you may prefer a hosted VM to your home computer.
If you are elected validator and don´t behave properly (node not online/reachable, wrong software version, etc...), your node´s balance will be slashed: you will lose testnet DOTs.
The next chapter goes into more details but here is the recipe. It is advised to do the following in the right order to avoid issues:
- install an appropriate polkadot version
- start it without any flag until your node is synced
- create an account using the Polkadot UI, save your seed and take note of your account´s address
- get testnet DOTs in your account
- restart your polkadot client with
polkadot --validator --key <seed> - check that your authority key matches
-
Extrinsics/staking/stake()your account - check that you show up in the
Storage/staking/intentions()list - wait until you show up in the
Storage/session/validators()list - observe your balance going hopefully up!
In order to be a validator you need the following:
- A node running a proper version of the polkadot client
- A node started with both
--validatorand--key .... More on that below - Some testnet DOTs
- Having staked
You can find more information regarding the installation of polkadot in the readme:
- install using cargo: https://github.com/paritytech/polkadot/blob/master/README.adoc#1-to-play
- using docker: https://github.com/paritytech/polkadot/blob/master/README.adoc#4-using-docker
At the time of writing the cutting edge latest version is not appropriate and should not be used by validators. Only version 0.2.1 works.
That´s easy, just run polakdot with --validator.
That can be a little tricky due to #474.
First open the UI at https://poc-2.polkadot.io/#/accounts.
Do NOT use the generated seed, use a string, preferable between 32 and 60 chars. Save this seed and take note of your account´s address.
You can now start your node using polkadot --validator --key <your seed here>.
When polkadot starts, it will confirm and display the address of the validator´s account.
Look for a log similar to Using authority key 5CFch3..... when polkadot starts. This MUST match the address of your validator´s account. If this is not the case, do not stake your account, you will get slashed.
In order for your validator account to be granted the right to validate, you will need testnet DOTs in that account, enough in regards to the other validator candidates.
You may ask for testnet DOTs on Riot in #polkadot-watercooler:matrix.org).
In order for your validator to effectively run, you will need to stake your account.
You can do so here. Select your account, category staking, extrinsic stake() and send the transaction.
If you did it right, you should see your account´s address showing in the intensions list. You find the list here under staking/intensions().
You are now almost good to go. You may be elected validator if there are enough free slots and your stake (balance) is higher than the other validator candidates.
Currently, there are 5 slots available. The dev team is operating 4 validators with high stake. That leaves one slot free for community validators. The number of available slots will likely vary over time. To check the current value, use the UI at Storage/staking/validatorCount().