Cant get Si5351 running - need a sample config.h please

[whallmann]

Is there a sample config.h where the si5351 board is running? I conncected a board to pin header of RS41 Ports 2 SDA and 3 SCL - see 3,8 volt on the VCC on si5351 - also set Si5351 CW on but see no signal on the clock0 output

. my config.h is appended.
Any help is welcome.
Wolf - DF7PN
df7pn_si5351_cw_config_h.txt

[whallmann]

i debuged a while and see that the board gets init ok. Seems there is Something wrong with the board. Good that i bought 2 of them. will check tomorrow.

[whallmann]

Meanwhile i connect another board. I set TX on 14 MHz and see a wide 500 kHz Signal in the Waterfall sounds crazy and waving around on the band. I tried power down to minimum 0 dB but nothing changes. So this project gets stopped now.

[mikaelnousiainen]

@whallmann Sounds definitely odd. Are you sure the voltage from your modded power supply (with just 1xAA battery) stays stable? I have only tested it (very successfully) with 2xAAs and no power supply mod.

The config entries that matter -- the following should send CW at 3595 kHz:

// Enable use of an externally connected I²C Si5351 clock generator chip for HF radio transmissions
#define RADIO_SI5351_ENABLE true

// Si5351 transmit power: 0..3
// Si5351 drive strength: 0 = 2mA, 1 = 4mA, 2 = 6mA, 3 = 8mA
#define RADIO_SI5351_TX_POWER 3

// Which modes to transmit using an externally connected Si5351 chip in the I²C bus
// The COUNT settings define the number of times that each type of transmission is repeated
#define RADIO_SI5351_TX_CW true
#define RADIO_SI5351_TX_CW_COUNT 1
#define RADIO_SI5351_TX_PIP false
#define RADIO_SI5351_TX_PIP_COUNT 6
#define RADIO_SI5351_TX_HORUS_V1 false
#define RADIO_SI5351_TX_HORUS_V1_COUNT 1
#define RADIO_SI5351_TX_HORUS_V2 false
#define RADIO_SI5351_TX_HORUS_V2_COUNT 4
#define RADIO_SI5351_TX_JT9 false
#define RADIO_SI5351_TX_JT9_COUNT 1
#define RADIO_SI5351_TX_JT65 false
#define RADIO_SI5351_TX_JT65_COUNT 1
#define RADIO_SI5351_TX_JT4 false
#define RADIO_SI5351_TX_JT4_COUNT 1
#define RADIO_SI5351_TX_WSPR false
#define RADIO_SI5351_TX_WSPR_COUNT 1
#define RADIO_SI5351_TX_FSQ false
#define RADIO_SI5351_TX_FSQ_COUNT 1
#define RADIO_SI5351_TX_FT8 false
#define RADIO_SI5351_TX_FT8_COUNT 1

// Transmit frequencies for the Si5351 transmitter modes
#define RADIO_SI5351_TX_FREQUENCY_CW         3595000UL
#define RADIO_SI5351_TX_FREQUENCY_PIP        3595000UL
#define RADIO_SI5351_TX_FREQUENCY_HORUS_V1   3608000UL
#define RADIO_SI5351_TX_FREQUENCY_HORUS_V2   3608000UL
#define RADIO_SI5351_TX_FREQUENCY_JT9        14085000UL    // Was: 14078700UL
#define RADIO_SI5351_TX_FREQUENCY_JT65       14085000UL    // Was: 14078300UL
#define RADIO_SI5351_TX_FREQUENCY_JT4        14085000UL    // Was: 14078500UL
#define RADIO_SI5351_TX_FREQUENCY_WSPR       14085000UL    // Was: 14097200UL
#define RADIO_SI5351_TX_FREQUENCY_FSQ        3608350UL    // Was: 7105350UL     // Base freq is 1350 Hz higher than dial freq in USB
#define RADIO_SI5351_TX_FREQUENCY_FT8        14085000UL    // Was: 14075000UL

Also remember to set the CW message in config.c (this would send out the call sign):

char *cw_message_templates[] = {
        "$cs",
        NULL
};

That said, I'd need to test this again locally if there is some regression...

Can you share your config.h and config.c files -- put them as attachments here in the comments (click the attach file icon above).

Also, can you take a photo of the waterfall spectrum or maybe record a video? Having something 500 kHz wide sounds like the on-board crystal on the Si5351 break-out board would not be working properly at all.

I've personally used the same type of Si5351 board (as in the photo).

[whallmann]

Late reply sorry. Thanks for answer.
Before read your answer above: Meanwhile tried 3 differnt boards - nothing - only wide scatter in the sdr - no real signal.
Will share more infos also files with hardcopys soon as you suggested.
Also read somehow that the Si5351 board needs high I²c bus speed. Will change and try from 100.000 to 200.000 Hz. This is only one of my thoughts ;-)
cu Wolf

[iz2fly]

At how many volts is the Si5351 powered?
Why is the RS41 powered only by a battery?
Why is the RS41 PCB broken? This could be the cause of the error.