This plug-in uses an undocumented KIA API to start, stop and lock your KIA. This API was discovered by insepecting the network traffic in the KIA Connect web app.
This plug-in will create a switch to turn the engine / climate control on and off as well as a lock mechanism to lock / unlock the doors. Several sensors will also be created so that you can build automations:
- Contact sensors for front left, front right, back left, back right doors as well as the hood and trunk.
- Exterior temperature sensor
- Battery level with low battery status
- Occupancy sensor that is "occupied" while the engine is running
Frequently calling this API could result in the consumption of your car's battery power. By default, we make one request per hour and make up to 5 requests after requesting a change of state. This is similar to how the KIA web app works.
- Battery percentage
- Fuel percentage
- Exterior weather
- Heated / air conditioned seats
- Defrost
- Heated steering wheel
- Occupancy sensor when engine is on
- Add support for other countries (Canada, Europe)
When flipping a switch in HomeKit, it could be several seconds before the desired state is achieved. This is due to the aysnc nature and overall speed of KIA's APIs. Typically, a remote command takes around 6 seconds to send, then around 10-15 seconds to be applied to the car.
The door contact sensors all have the same name. Unfortunately this is a limitation of a HomeKit. To overcome this, I would need to refactor the code to create a new Accessory per sensor.
You will need the following items:
- Your username / password for the KIA Connect web app.
- Your VIN number
When the car is started, we will attempt to bring the cabin to the specified temperature. By default, your car will run for 5 minutes, then turn off. This value should be given in Farenheit.
When the plugin is first started, we get your car's latest info from KIA. After that, we will refresh that info every refreshInterval until the plugin is stopped. This value should be given in milliseconds.
In addition to refreshing every refreshInterval we will also request vehicle info after an action is requested. This helps HomeKit stay in sync since these actions take some time and could fail due to factors outside of our control.
{
"platforms": [
{
"name": "homebridge-kia-connect",
"platform": "KiaConnect",
"email": "[email protected]",
"password": "my-secret-password",
"cars": [
{
"name": "Telluride",
"vin": "XXXXXXXXXXXXXXXXX",
"targetTemperature": "68",
"refreshInterval": 3600000
}
]
}
]
}
To develop Homebridge plugins you must have Node.js 12 or later installed, and a modern code editor such as VS Code. This plugin template uses TypeScript to make development easier and comes with pre-configured settings for VS Code and ESLint. If you are using VS Code install these extensions:
Using a terminal, navigate to the project folder and run this command to install the development dependencies:
npm install
Open the package.json and change the following attributes:
name- this should be prefixed withhomebridge-or@username/homebridge-and contain no spaces or special characters apart from a dashesdisplayName- this is the "nice" name displayed in the Homebridge UIrepository.url- Link to your GitHub repobugs.url- Link to your GitHub repo issues page
When you are ready to publish the plugin you should set private to false, or remove the attribute entirely.
Open the src/settings.ts file and change the default values:
PLATFORM_NAME- Set this to be the name of your platform. This is the name of the platform that users will use to register the plugin in the Homebridgeconfig.json.PLUGIN_NAME- Set this to be the same name you set in thepackage.jsonfile.
Open the config.schema.json file and change the following attribute:
pluginAlias- set this to match thePLATFORM_NAMEyou defined in the previous step.
TypeScript needs to be compiled into JavaScript before it can run. The following command will compile the contents of your src directory and put the resulting code into the dist folder.
npm run build
Run this command so your global install of Homebridge can discover the plugin in your development environment:
npm link
You can now start Homebridge, use the -D flag so you can see debug log messages in your plugin:
homebridge -D
If you want to have your code compile automatically as you make changes, and restart Homebridge automatically between changes, you first need to add your plugin as a platform in ~/.homebridge/config.json:
{
...
"platforms": [
{
"name": "Config",
"port": 8581,
"platform": "config"
},
{
"name": "<PLUGIN_NAME>",
//... any other options, as listed in config.schema.json ...
"platform": "<PLATFORM_NAME>"
}
]
}
and then you can run:
npm run watch
This will launch an instance of Homebridge in debug mode which will restart every time you make a change to the source code. It will load the config stored in the default location under ~/.homebridge. You may need to stop other running instances of Homebridge while using this command to prevent conflicts. You can adjust the Homebridge startup command in the nodemon.json file.
You can now start customising the plugin template to suit your requirements.
src/platform.ts- this is where your device setup and discovery should go.src/platformAccessory.ts- this is where your accessory control logic should go, you can rename or create multiple instances of this file for each accessory type you need to implement as part of your platform plugin. You can refer to the developer documentation to see what characteristics you need to implement for each service type.config.schema.json- update the config schema to match the config you expect from the user. See the Plugin Config Schema Documentation.
Given a version number MAJOR.MINOR.PATCH, such as 1.4.3, increment the:
- MAJOR version when you make breaking changes to your plugin,
- MINOR version when you add functionality in a backwards compatible manner, and
- PATCH version when you make backwards compatible bug fixes.
You can use the npm version command to help you with this:
# major update / breaking changes
npm version major
# minor update / new features
npm version update
# patch / bugfixes
npm version patchWhen you are ready to publish your plugin to npm, make sure you have removed the private attribute from the package.json file then run:
npm publish
If you are publishing a scoped plugin, i.e. @username/homebridge-xxx you will need to add --access=public to command the first time you publish.
You can publish beta versions of your plugin for other users to test before you release it to everyone.
# create a new pre-release version (eg. 2.1.0-beta.1)
npm version prepatch --preid beta
# publish to @beta
npm publish --tag=betaUsers can then install the beta version by appending @beta to the install command, for example:
sudo npm install -g homebridge-example-plugin@beta