ci(pre-commit): Add spaces between numbers and units

Author: P-R-O-C-H-Y

libraries/Zigbee/examples/Zigbee_Electrical_AC_Sensor/README.md

@@ -12,20 +12,20 @@ Currently, this example supports the following targets.
 ## AC Electrical Measurement Functions
 
  * After this board first starts up, it would be configured locally to report AC electrical measurements:
-   - AC voltage in volts (0-300.00V)
-   - AC current in amps (0-10.000A)
-   - AC power in watts (0-3200.0W)
-   - AC frequency in hertz (0-65.000Hz)
+   - AC voltage in volts (0-300.00 V)
+   - AC current in amps (0-10.000 A)
+   - AC power in watts (0-3200.0 W)
+   - AC frequency in hertz (0-65.000 Hz)
  * Holding the button (BOOT) for more than 3 seconds will trigger a factory reset of the device.
  * The device reports measurements every 2 seconds with simulated values.
 
 ## Measurement Precision
 
 The example demonstrates how to set up proper measurement precision using multiplier and divisor values:
- * Voltage: 1/100 = 0.01V (1 unit = 10mV)
- * Current: 1/1000 = 0.001A (1 unit = 1mA)
- * Power: 1/10 = 0.1W (1 unit = 100mW)
- * Frequency: 1/1000 = 0.001Hz (1 unit = 1mHz)
+ * Voltage: 1/100 = 0.01 V (1 unit = 10 mV)
+ * Current: 1/1000 = 0.001 A (1 unit = 1 mA)
+ * Power: 1/10 = 0.1 W (1 unit = 100 mW)
+ * Frequency: 1/1000 = 0.001 Hz (1 unit = 1 mHz)
 
 These settings ensure accurate reporting of measurements with proper decimal precision in the Zigbee network.
 

libraries/Zigbee/examples/Zigbee_Electrical_AC_Sensor_MultiPhase/README.md

@@ -12,20 +12,20 @@ Currently, this example supports the following targets.
 ## AC Electrical Measurement Functions
 
  * After this board first starts up, it would be configured locally to report AC electrical measurements:
-   - AC voltage in volts (0-300.00V) for each phase (A, B, C)
-   - AC current in amps (0-10.000A) for each phase (A, B, C)
-   - AC power in watts (0-3200.0W) for each phase (A, B, C)
-   - AC frequency in hertz (0-65.000Hz) shared across all phases
+   - AC voltage in volts (0-300.00 V) for each phase (A, B, C)
+   - AC current in amps (0-10.000 A) for each phase (A, B, C)
+   - AC power in watts (0-3200.0 W) for each phase (A, B, C)
+   - AC frequency in hertz (0-65.000 Hz) shared across all phases
  * Holding the button (BOOT) for more than 3 seconds will trigger a factory reset of the device.
  * The device reports measurements every 2 seconds with simulated values.
 
 ## Measurement Precision
 
 The example demonstrates how to set up proper measurement precision using multiplier and divisor values:
- * Voltage: 1/100 = 0.01V (1 unit = 10mV)
- * Current: 1/1000 = 0.001A (1 unit = 1mA)
- * Power: 1/10 = 0.1W (1 unit = 100mW)
- * Frequency: 1/1000 = 0.001Hz (1 unit = 1mHz)
+ * Voltage: 1/100 = 0.01 V (1 unit = 10 mV)
+ * Current: 1/1000 = 0.001 A (1 unit = 1 mA)
+ * Power: 1/10 = 0.1 W (1 unit = 100 mW)
+ * Frequency: 1/1000 = 0.001 Hz (1 unit = 1 mHz)
 
 These settings ensure accurate reporting of measurements with proper decimal precision in the Zigbee network.
 

libraries/Zigbee/examples/Zigbee_Electrical_DC_Sensor/README.md

@@ -12,18 +12,18 @@ Currently, this example supports the following targets.
 ## DC Electrical Measurement Functions
 
  * After this board first starts up, it would be configured locally to report DC electrical measurements:
-   - DC voltage in millivolts (0-5000mV)
-   - DC current in milliamps (0-1000mA)
-   - DC power in milliwatts (0-5000mW)
+   - DC voltage in millivolts (0-5000 mV)
+   - DC current in milliamps (0-1000 mA)
+   - DC power in milliwatts (0-5000 mW)
  * Holding the button (BOOT) for more than 3 seconds will trigger a factory reset of the device.
  * The device reports measurements every 30 seconds if the value changes by more than the configured delta.
 
 ## Measurement Precision
 
 The example demonstrates how to set up proper measurement precision using multiplier and divisor values:
- * Voltage: 1/1000 = 0.001V (1 unit = 1mV)
- * Current: 1/1000 = 0.001A (1 unit = 1mA)
- * Power: 1/1000 = 0.001W (1 unit = 1mW)
+ * Voltage: 1/1000 = 0.001 V (1 unit = 1 mV)
+ * Current: 1/1000 = 0.001 A (1 unit = 1 mA)
+ * Power: 1/1000 = 0.001 W (1 unit = 1 mW)
 
 These settings ensure accurate reporting of measurements with proper decimal precision in the Zigbee network.