PI MQTT GPIO

Expose the Raspberry Pi GPIO pins, external IO modules, streams and I2C sensors to an MQTT server. This allows pins to be read and switched by reading or writing messages to MQTT topics. The streams and I2C sensors will be read periodically and publish their values.

GPIO Modules

• Raspberry Pi GPIO (raspberrypi)
• Orange Pi GPIO (orangepi)
• PCF8574 IO chip (pcf8574)
• PiFaceDigital 2 IO board (piface2)
• Beaglebone GPIO (beaglebone)

Sensors

• LM75 i2c temperature sensor (lm75)
• DHT11 DHT22 AM2302 temperature/humidity sensor (dht22)
• BH1750 light level sensor (bh1750)
• DS18S20, DS1822, DS18B20, DS1825, DS28EA00, MAX31850K one-wire temperature sensors: (ds18b)
• HC-SR04 ultrasonic distance sensor (hcsr04)

Streams

• Serial port (streamserial)

Installation

pip install pi-mqtt-gpio

Execution

python -m pi_mqtt_gpio.server config.yml

Configuration

Configuration is handled by a YAML file which is passed as an argument to the server on startup.

Pins

With the following example config, switch pin 21 on by publishing to the home/kitchen/output/lights/set topic with a payload of ON, and pin 22 by publishing to home/kitchen/output/fan/set.

mqtt:
  host: test.mosquitto.org
  port: 1883
  user: ""
  password: ""
  topic_prefix: home/kitchen

gpio_modules:
  - name: raspberrypi
    module: raspberrypi

digital_outputs:
  - name: lights
    module: raspberrypi
    pin: 21
    on_payload: "ON"
    off_payload: "OFF"
    initial: low  # This optional value controls the initial state of the pin before receipt of any messages from MQTT. Valid options are 'low' and 'high'.
    retain: yes # This option value controls if the message is retained. Default is no.

  - name: fan
    module: raspberrypi
    pin: 22
    inverted: yes  # This pin may control an open-collector output which is "on" when the output is "low".
    on_payload: "ON"
    off_payload: "OFF"

Or to receive updates on the status of an input pin, subscribe to the home/input/doorbell topic:

mqtt:
  host: test.mosquitto.org
  port: 1883
  user: ""
  password: ""
  topic_prefix: home

gpio_modules:
  - name: raspberrypi
    module: raspberrypi
    cleanup: no  # This optional boolean value sets whether the module's `cleanup()` function will be called when the software exits.

digital_inputs:
  - name: doorbell
    module: raspberrypi
    pin: 22
    on_payload: "ON"
    off_payload: "OFF"
    pullup: yes
    pulldown: no

Sensors

Receive updates on the value of a sensor by subscribing to the home/sensor/<sensor input name> topic. In the following example, this would be home/sensor/temperature:

mqtt:
  host: test.mosquitto.org
  port: 1883
  user: ""
  password: ""
  topic_prefix: home

sensor_modules:
  - name: lm75
    module: lm75
    i2c_bus_num: 1
    chip_addr: 0x48
    cleanup: no  # This optional boolean value sets whether the module's `cleanup()` function will be called when the software exits.

  - name: dht22
    module: dht22
    type: AM2302 # can be  DHT11, DHT22 or AM2302
    pin: 4

  - name: bh1750
    module: bh1750
    i2c_bus_num: 1
    chip_addr: 0x23

  - name: ds18b22
    module: ds18b
    type: DS18S20
    address: 000803702e49

  - name: hcsr04
    module: hcsr04
    pin_echo: 27
    pin_trigger: 17
    burst: 10  # number of measurements for output of distance value in [cm]

sensor_inputs:
  - name: temperature
    module: lm75
    interval: 15 #interval in seconds, that a value is read from the sensor and a update is published
    digits: 4 # number of digits to be round

- name: dht22_temperature 
    module: dht22
    interval: 10 #interval in seconds, that a value is read from the sensor and a update is published
    digits: 4 # number of digits to be round
    type: temperature # Can be temperature or humidity

- name: dht22_humidity 
    module: dht22
    interval: 10 #interval in seconds, that a value is read from the sensor and a update is published
    digits: 4 # number of digits to be round
    type: humidity # Can be temperature or humidity   

- name: bh1750_lux
    module: bh1750
    interval: 10
    digits: 2

- name: ds18b22
    module: ds18b22
    interval: 60
    digits: 2

  - name: distance
    module: hcsr04
    interval: 10  # measurement every 10s
    digits: 1

Streams

Transmit data by publishing to the home/stream/<stream write name> topic. In the following example, this would be home/stream/serialtx.

Receive data from a stream by subscribing to the home/stream/<stream read name> topic. In the following example, this would be home/stream/serialrx.

The stream data is parsed using Python's string_escape to allow the transfer of control characters.

mqtt:
  host: test.mosquitto.org
  port: 1883
  user: ""
  password: ""
  topic_prefix: home

stream_modules:
  - name: serialcomms
    module: streamserial
    device: /dev/ttyS0
    baud: 115200
    bytesize: 8 # Number of data bits in word. Can be: 5,6,7,8
    parity: none # Parity can be one of none,odd,even,mark,space
    stopbits: 1 # Number of stop bits. Can be: 1,1.5,2
    cleanup: no  # This optional boolean value sets whether the module's `cleanup()` function will be called when the software exits.

stream_reads:
  - name: serialrx
    module: serialcomms
    interval: 0.25 # Stream read polling interval in seconds

stream_writes:
  - name: serialtx
    module: serialcomms

Testing example:

# -N disables printing extra new line on each subscription
mosquitto_sub -h <broker url> -t <topic prefix>/stream/serialrx -N

mosquitto_pub -h <broker url> -t <topic prefix>/stream/serialtx -m "testing123\r\n"

OrangePi boards

You need to specify what OrangePi board you use

gpio_modules:
  - name: orangepi
    module: orangepi
    board: zero # Supported: ZERO, R1, ZEROPLUS, ZEROPLUS2H5, ZEROPLUS2H3, PCPCPLUS, ONE, LITE, PLUS2E, PC2, PRIME
    mode: board

SSL/TLS

You may want to connect to a remote server, in which case it's a good idea to use an encrypted connection. If the server supports this, then you can supply the relevant config values for the tls_set() command.

mqtt:
  host: test.mosquitto.org
  port: 8883
  tls:
    enabled: yes

You may need to supply a trusted CA certificate, as instructed on https://test.mosquitto.org/.

mqtt:
  host: test.mosquitto.org
  port: 8883
  tls:
    enabled: yes
    ca_certs: mosquitto.org.crt

Or you might want to use SSL/TLS but not verify the server's certificate (not recommended).

mqtt:
  host: test.mosquitto.org
  port: 8883
  tls:
    enabled: yes
    cert_reqs: CERT_NONE
    insecure: yes

Temporary Set

You may want to set the output to a given value for a certain amount of time. This can be done using the /set_on_ms and /set_off_ms topics. If an output is already set to that value, it will stay that value for the given amount of milliseconds and then switch to the opposite.

For example, to set an output named light on for one second, publish 1000 as the payload to the myprefix/output/light/set_on_ms topic.

If you want to force an output to always set to on/off for a configured amount of time, you can add timed_set_ms to your output config. This will mean that if you send "ON" to myprefix/output/light/set, then it will turn the light on for however many milliseconds are configured in timed_set_ms and then turn it off again. Whether the light is on already or not, sending "ON" will make the light eventually turn off after timed_set_ms milliseconds. This also works inversely with sending "OFF", which will turn the light off, then on after timed_set_ms milliseconds, so don't expect this to always keep your devices set to on/off.

Interrupts

Interrupts may be used for inputs instead of polling for raspberry modules. Specify interrupt and a strategy rising, falling or both to switch from polling to interrupt mode. The bouncetime is default 100ms but may be changed (at least 1ms). The interrupt trigger will send a configurable interrupt_payload (default: "INT") and not the current value of the pin: reading the current pin value in the ISR, returned 'old' values. Reading again in the ISR after 100ms gave 'changed' value, but waiting in ISR is not a good solution. So only a trigger message is transmitted on each ISR trigger.

digital_inputs:
  - name: button_left
    module: raspberrypi
    pin: 23
    interrupt_payload: "trigger"
    pullup: no
    pulldown: yes
    interrupt: falling
    bouncetime: 200

Modules

The IO modules are pluggable and multiple may be used at once. For example, if you have a Raspberry PI with some GPIO pins in use and also a PCF8574 IO expander on the I2C bus, you'd list two modules in the gpio_modules section and set up the inputs and outputs accordingly:

mqtt:
  host: test.mosquitto.org
  port: 1883
  user: ""
  password: ""
  topic_prefix: pimqttgpio/mydevice

gpio_modules:
  - name: raspberrypi
    module: raspberrypi

  - name: pcf8574
    module: pcf8574
    i2c_bus_num: 1
    chip_addr: 0x20

  - name: orangepi
    module: orangepi
    board: r1
    mode: board

digital_inputs:
  - name: button
    module: raspberrypi
    pin: 21  # This device is connected to pin 21 of the Raspberry PI GPIO
    on_payload: "ON"
    off_payload: "OFF"
    pullup: no
    pulldown: yes

digital_outputs:
  - name: bell
    module: pcf8574
    pin: 2  # This device is connected to pin 2 of the PCF8574 IO expander
    on_payload: "ON"
    off_payload: "OFF"

MQTT Status Topic

MQTT supports a "last will and testament" (LWT) feature which means the server will publish to a configured topic with a message of your choosing if it loses connection to the client unexpectedly. Using this feature, this project can be configured to publish to a status topic as depicted in the following example config:

mqtt:
  ...
  status_topic: status
  status_payload_running: running
  status_payload_stopped: stopped
  status_payload_dead: dead

These are in fact the default values should the configuration not be provided, but they can be changed to whatever is desired. The status_topic will be appended to the configured topic_prefix, if any. For example, with the following config:

mqtt:
  ...
  topic_prefix: home/office
  status_topic: status

the status messages will appear on topic home/office/status.

MQTT Client ID

The MQTT client ID identifies your instance of pi-mqtt-gpio with your MQTT broker. It allows the broker to keep track of the state of your instance so that it can resume when it reconnects. This means that the ID must be unique for each instance that connects to the MQTT broker.

Since the MQTT client ID for each instance of pi-mqtt-gpio is based on the topic_prefix supplied in config (#24), having multiple instances share the same topic_prefix will require you to set a different client_id for each:

Device 1

mqtt:
  host: test.mosquitto.org
  client_id: pi-mqtt-gpio-device1
  topic_prefix: home/office

Device 2

mqtt:
  host: test.mosquitto.org
  client_id: pi-mqtt-gpio-device2
  topic_prefix: home/office

Logging

Logging may be configured by including a logging section in your config.yml. The standard Python logging system is used, so configuration questions should be answered by looking at the Python logging howto.

The default config is set as follows. If you wish to change this, copy and paste this section into your config.yml and change whichever parts you'd like.

logging:
  version: 1
  formatters:
    simple:
      format: "%(asctime)s %(name)s (%(levelname)s): %(message)s"
  handlers:
    console:
      class: logging.StreamHandler
      level: DEBUG
      formatter: simple
      stream: ext://sys.stdout
  loggers:
    mqtt_gpio:
      level: INFO
      handlers: [console]
      propagate: yes

Serving Suggestion

This project is not tied to any specific deployment method, but one recommended way is to use virtualenv and supervisor. This will launch the project at boot time and handle restarting and log file rotation. It's quite simple to set up:

If using Raspbian, install supervisor with apt.

sudo apt-get update
sudo apt-get install supervisor

Not strictly necessary, but it's recommended to install the project into a virtualenv. Generally, the best way to get an up-to-date version of virtualenv is to use pip install --upgrade virtualenv. If you don't already have pip, then check here for installation instructions.

cd /home/pi
virtualenv ve
. ve/bin/activate
pip install pi-mqtt-gpio

Create yourself a config file, following instructions and examples above, and save it somewhere, such as /home/pi/pi-mqtt-gpio.yml.

Create a supervisor config file in /etc/supervisor/conf.d/pi-mqtt-gpio.conf something along the lines of the following:

[program:pi_mqtt_gpio]
command = /home/pi/ve/bin/python -m pi_mqtt_gpio.server pi-mqtt-gpio.yml
directory = /home/pi
redirect_stderr = true
stdout_logfile = /var/log/pi-mqtt-gpio.log

Save the file and then run the following to update supervisor and start the program running.

sudo supervisorctl update

Check the status of your new supervisor job:

sudo supervisorctl status

Check the supervisor docs for more supervisorctl commands.

Docker

Two images have been created for Docker. One using the x86_64 architecture (for Intel and AMD CPUs) and one for the ARM architecture (for Raspberry Pi etc.). The tags of the images are therefore flyte/mqtt-gpio:x86_64 and flyte/mqtt-gpio:armv7l. These are the outputs of uname -m on the two platforms they've been built on. For the following examples I'll assume you're running on Raspberry Pi.

You may also run this software using Docker. You must create your config file as above, then run the docker image:

docker run -ti --rm -v /path/to/your/config.yml:/config.yml flyte/mqtt-gpio:armv7l

Or to run in the background:

docker run -d --name mqtt-gpio -v /path/to/your/config.yml:/config.yml flyte/mqtt-gpio:armv7l

You'll most likely want to use some hardware devices in your config, since that's what this project is all about. For example, if you wish to use the i2c bus, pass it through with a --device parameter:

docker run -ti --rm -v /path/to/your/config.yml:/config.yml --device /dev/i2c-0 flyte/mqtt-gpio:armv7l

If you aren't able to find the exact device path to use, then you can also run the docker container in --privileged mode which will pass all of the devices through from the host:

docker run -ti --rm -v /path/to/your/config.yml:/config.yml --privileged flyte/mqtt-gpio:armv7l

Please raise an issue on Github if you find that any of this information is incorrect.