Skip to content

Latest commit

 

History

History
254 lines (157 loc) · 6.67 KB

znapzendzetup.pod

File metadata and controls

254 lines (157 loc) · 6.67 KB
Raw

NAME

znapzendzetup - znapzend setup utility

SYNOPSIS

znapzendzetup command [options...]

where 'command' is one of the following:

create  [--pfexec|sudo] \
        [--recursive] [--mbuffer=<path>[:<port>]] [--mbuffersize=<size>] \
        [--pre-snap-command=<command>] \
        [--post-snap-command=<command>] \
        [--tsformat=<format>] --donotask \
        SRC plan dataset \
        [ DST[:key] plan [[user@]host:]dataset ]

delete  [--pfexec|sudo] [--dst=key] <src_dataset>

edit    [--pfexec|sudo]
        [--recursive=on|off] [--mbuffer=<path>[:<port>]|off] [--mbuffersize=<size>] \
        [--pre-snap-command=<command>|off] \
        [--post-snap-command=<command>|off] \
        [--tsformat=<format>] --donotask \
        SRC [plan] dataset \
        [ DST:key [plan] [dataset] ]

edit    [--pfexec|sudo] <src_dataset>

enable  [--pfexec|sudo] <src_dataset>

disable [--pfexec|sudo] <src_dataset>

list    [--pfexec|sudo] [src_dataset]

export  [--pfexec|sudo] <src_dataset>

import  [--pfexec|sudo] [--write] [--prop <property>=<value>, [--prop ...] ...]
        <src_dataset> [<prop_dump_file>]

help

man

DESCRIPTION

Use znapzendsetup to configure your backup tasks. The cli is modled after the zfs commandline.

After modifying the configuration, send a HUP signal to your znapzend daemon for it to re-read the configuration.

Below a few notes on main commands.

create

The heart of the znapzend backup is the plan. The plan specifies how often to backup and for how long to keep the backups. A plan is required both for the source and the destination datasets.

The plan consists of a series of retention periodes to interval associations:

retA=>intA,retB=>intB,...

Both intervals and retention periods are expressed in standard units of time or multiples of them. You can use both the full name or a shortcut according to the following table:

second|sec|s
minute|min
hour|h
day|d
week|w
month|mon|m
year|y

To keep one copy every 30 minutes for one week, specify:

1week=>30min

To keep one copy every two days for 10 years:

10year=>2day

In a minimal setup, you just specify a plan for the SRC fileset. This will cause snapshots to be taken and destroyed according to the plan. You can then add one or several destinations (DST) both local (preferably on a different pool) or remote.

When adding multiple DST entries, each will get labled for later identification, optionally you can specify your own label.

--tsformat=limited-strftime-format

The --tsformat option specifies how the names of the snapshots are constructed.

The syntax is strftime-like. The string must consist of the mandatory

%Y %m %d %H %M %S

Optionally,

- _ . :

characters as well as any alphanumeric character are allowed.

If not specified, --tsformat defaults to %Y-%m-%d-%H%M%S.

If --tsformat string is suffixed by a 'Z', times will be in UTC. E.g.:

--tsformat='%Y-%m-%dT%H:%M:%SZ'

NOTE: that windows will probably not like the : characters. So if you intend to browse the snapshots with windos, you may want to use a different separator.

--mbuffer=/usr/bin/mbuffer

Specify the path to your copy of the mbuffer utility.

--mbuffer=/usr/bin/mbuffer:31337

Specifiy the path to your copy of the mbuffer utility and the port used on the destination. Caution: znapzend will send the data directly from source mbuffer to destination mbuffer, thus data stream is not encrypted.

--mbuffersize=number{b|k|M|G}

The size of the mbuffer can be set with the --mbuffersize option. It supports the following units:

b, k, M, G

To specify a mbuffer size of 100MB:

--mbuffersize=100M

If not set, the buffer size defaults to 1GB.

--donotask

Apply changes immediately. Without being asked if the config is as you intended it to be.

--pre-snap-command=/path/bin args, --post-snap-command=/path/bin args

Run commands/scripts before and after snapshots are taken on source. e.g. for database locking/flushing (pre) and unlocking (post).

delete

to remove configuration from a dataset just give its name

znapzendzetup delete I<dataset>

the delete function understands the following options

--dst=key

to only remove a destination, specify the key of the destionation. Use the list function to see the keys.

edit

modify the configuration of a dataset. see the descriptions in the create function for details.

If edit is used with a source dataset as single argument, properties can be edited in an editor.

export

dumps the backup configuration of a dataset

znapzendzetup export I<dataset>

import

reads configuration data from a file or STDIN and prints it content

--write

actually store the new configuration into the dataset given on the commandline.

--prop key="value" [ --prop ... ]

may be called multiple times to override properties in the imported config.

EXAMPLES

create a complex backup task

znapzendzetup create --recursive --mbuffer=/opt/omni/bin/mbuffer \
   --mbuffersize=1G --tsformat='%Y-%m-%d-%H%M%S' \
   --pre-snap-command="/bin/sh /usr/local/bin/lock_flush_db.sh" \
   --post-snap-command="/bin/sh /usr/local/bin/unlock_db.sh" \
   SRC '7d=>1h,30d=>4h,90d=>1d' tank/home \
   DST:a '7d=>1h,30d=>4h,90d=>1d,1y=>1w,10y=>1month' backup/home \
   DST:b '7d=>1h,30d=>4h,90d=>1d,1y=>1w,10y=>1month' root@bserv:backup/home

copy the setup from one fileset to another

znapzendzetup export tank/home | znapzendzetup import --write tank/new_home

COPYRIGHT

Copyright (c) 2014 by OETIKER+PARTNER AG. All rights reserved.

LICENSE

This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/.

AUTHOR

Tobias Oetiker <[email protected]> Dominik Hassler <[email protected]>

HISTORY

2014-07-22 had Pre and post snapshot commands 2014-06-29 had Flexible snapshot time format 2014-06-01 had Multi destination backup 2014-05-30 had Initial Version