diff --git a/config/zooz/zen30.xml b/config/zooz/zen30.xml index 0c2c7b6beb..ff3add27e3 100644 --- a/config/zooz/zen30.xml +++ b/config/zooz/zen30.xml @@ -1,7 +1,7 @@ - - - Double Switch - PRODUCT FEATURES: + + + Double Switch + PRODUCT FEATURES: - Manual or Z-Wave control of 2 separate loads (dimmer + relay) - Perfect replacement for a fan / light combo (neutral wire required) - Scene control for multi-tap scenarios on select hubs @@ -9,7 +9,7 @@ - 4-color LED indicator and air-gap switch for added safety - Fully customizable dimming features including ramp rate, on brightness level, and double tap to full brightness -- Remembers and restores on/off status a􀈇er power failure +- Remembers and restores on/off status after power failure - Built-in Z-Wave Plus signal repeater to extend network range - S2 security protocol and 500 Z-Wave chip @@ -21,148 +21,163 @@ SPECIFICATIONS: - Relay Max Load: 15 A (1/2 HP) - Operating Temperature: 32-104° F (0-40° C) - Installation and Use: Indoor only - - http://www.openzwave.com/device-database/027a:a008:a000 - http://www.getzooz.com/ - http://www.support.getzooz.com/kb/section/134 - images/zooz/zen30.png - https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3791/zooz-s2-double-switch-zen30-ver1-manual-online.pdf - 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. 2. Tap the upper paddle on the switch 3 times quickly. - 1. Bring your Z-Wave gateway (hub) close to the switch if possible. -2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) + + http://www.openzwave.com/device-database/027a:a008:a000 + http://www.getzooz.com/ + http://www.support.getzooz.com/kb/section/134 + images/zooz/zen30.png + https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3791/zooz-s2-double-switch-zen30-ver1-manual-online.pdf + 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. 2. Tap the upper paddle on the switch 3 times quickly. + 1. Bring your Z-Wave gateway (hub) close to the switch if possible. +2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) 3. Tap the lower paddle on the switch 3 times quickly 4. Your hub will confirm exclusion and the device will disappear from your controller's device list - If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, press and hold the lower paddle on the dimmer for at least 15 seconds until the LED indicators start flashing, then release. Then immediately press and hold the upper paddle on the dimmer for at least 15 seconds. The LED indicators will flash again to confirm successful reset. - https://products.z-wavealliance.org/products/3791 - U.S. / Canada / Mexico - ZEN30 - - Initial Metadata Import - - + If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, press and hold the lower paddle on the dimmer for at least 15 seconds until the LED indicators start flashing, then release. Then immediately press and hold the upper paddle on the dimmer for at least 15 seconds. The LED indicators will flash again to confirm successful reset. + https://products.z-wavealliance.org/products/3791 + U.S. / Canada / Mexico + ZEN30 + + Initial Metadata Import + Updated for firmware version 1.04 + + - - - - LED Indicator Mode for Dimmer. Normal has the dimmer (top) LED indication on when the switch is off, off when the switch is on. Default: Normal - - - - - - - LED Indicator Mode for Relay. Normal has the relay (bottom) LED indication on when the switch is off, off when the switch is on. Default: Normal - - - - - - - LED Indicater color for Dimmer. White, Blue, Green or Red. Default: White - - - - - - - LED Indicater color for Relay. White, Blue, Green or Red. Default: White - - - - - - - LED Indicater Brightness for Dimmer. Bright (100%), Medium (60%) or Low (30%). Default: Medium - - - - - - LED Indicater Brightness for Relay. Bright (100%), Medium (60%) or Low (30%). Default: Medium - - - - - - LED Indicator Mode for Scene Control. Enable/Disable LED indicators next to the dimmer lighting up when a scene is selected. Default: disabled - - - - - Auto Turn-Off Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) - - - Auto Turn-On Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) - - - Auto Turn-Off Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) - - - Auto Turn-On Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) - - - On Off Status After Power Failure. Default: Restore both to prior state - - - - - - - - - - - - Ramp Rate Control for Dimmer. Adjust the ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. Note that 0 is instant. Default: 1 - - - Minimum Brightness. Set the minimum brightness level (in %) for your dimmer. You won't be able to dim the light below the set value. Default: 1 - - - Maximum Brightness. Set the maximum brightness level (in %) for your dimmer. You won't be able to add brightness to the light beyond the set value. Default: 99 - - - Double Tap Function for Dimmer. When set to full, turns light on to 100%. If set to maximum level, turns light on to % set in Parameter 15. Default: full - - - - - Enable/Disable Double-tap for Dimmer. Enables/Disables the double-tap fucntion and assign brightness to single tap. enabled: single tap turns on to maximum brightness level. disabled (last level): single tap returns to last brightness level. disabled (full/max level): single tap returns to full brightmess. Default: enabled - - - - - - Enable/Disable Load Control for Dimmer (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the dimmer will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled - - - - - - Enable/Disable Load Control for Relay (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the relay will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled - - - - - - Choose how many seconds it takes for the dimmer to go from 0% to 100% brightness when pressing and holding the paddle. Default: 4. - - - Z-Wave Ramp Rate for Dimmer. Choose if you would like to match the Z-Wave on/off ramp rate with the manual ramp rate or set it separately on your own. Default: match. - - - - - Default Brightness Level On for Dimmer. Set custom brightness level (in %) for the dimmer to come on to at single tap. Choose 0 for last brightness level. Default: 0. - - + + + + LED Indicator Mode for Dimmer. Normal has the dimmer (top) LED indication on when the switch is off, off when the switch is on. Default: Normal + + + + + + + LED Indicator Mode for Relay. Normal has the relay (bottom) LED indication on when the switch is off, off when the switch is on. Default: Normal + + + + + + + LED Indicater color for Dimmer. White, Blue, Green or Red. Default: White + + + + + + + LED Indicater color for Relay. White, Blue, Green or Red. Default: White + + + + + + + LED Indicater Brightness for Dimmer. Bright (100%), Medium (60%) or Low (30%). Default: Medium + + + + + + LED Indicater Brightness for Relay. Bright (100%), Medium (60%) or Low (30%). Default: Medium + + + + + + LED Indicator Mode for Scene Control. Enable/Disable LED indicators next to the dimmer lighting up when a scene is selected. Default: disabled + + + + + Auto Turn-Off Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) + + + Auto Turn-On Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) + + + Auto Turn-Off Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) + + + Auto Turn-On Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) + + + On Off Status After Power Failure. Default: Restore both to prior state + + + + + + + + + + + + Ramp Rate Control for Dimmer. Adjust the ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. Note that 0 is instant. Default: 1 + + + Minimum Brightness. Set the minimum brightness level (in %) for your dimmer. You won't be able to dim the light below the set value. Default: 1 + + + Maximum Brightness. Set the maximum brightness level (in %) for your dimmer. You won't be able to add brightness to the light beyond the set value. Default: 99 + + + Double Tap Function for Dimmer. When set to full, turns light on to 100%. If set to maximum level, turns light on to % set in Parameter 15. Default: full + + + + + Enable/Disable Double-tap for Dimmer. Enables/Disables the double-tap fucntion and assign brightness to single tap. enabled: single tap turns on to maximum brightness level. disabled (last level): single tap returns to last brightness level. disabled (full/max level): single tap returns to full brightmess. Default: enabled + + + + + + Enable/Disable Load Control for Dimmer (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the dimmer will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled + + + + + + Enable/Disable Load Control for Relay (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the relay will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled + + + + + + Choose how many seconds it takes for the dimmer to go from 0% to 100% brightness when pressing and holding the paddle. Default: 4. + + + Default Brightness Level On for Dimmer. Set custom brightness level (in %) for the dimmer to come on to at single tap. Choose 0 for last brightness level. Default: 0. + + + Sets behavior of the dimmer when physical control is disabled + + + + + Sets behavior of the relay when physical control is disabled + + + + + Set the brightness level the dimmer will turn on to when off and when lower paddle is held DOWN for a second. Default: 20 + + + Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. + + + + + - - - - - - - - + + + + + + + +