-
Notifications
You must be signed in to change notification settings - Fork 1
/
Copy pathstm32f769i_discovery_qspi.c
1166 lines (998 loc) · 37.4 KB
/
stm32f769i_discovery_qspi.c
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
/**
******************************************************************************
* @file stm32f769i_discovery_qspi.c
* @author MCD Application Team
* @brief This file includes a standard driver for the MX25L512 QSPI
* memory mounted on STM32F769I-Discovery board.
*
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@verbatim
==============================================================================
##### How to use this driver #####
==============================================================================
[..]
(#) This driver is used to drive the MX25L512 QSPI external
memory mounted on STM32F769I-Discovery board.
(#) This driver need a specific component driver (MX25L51245G) to be included with.
(#) Initialization steps:
(++) Initialize the QPSI external memory using the BSP_QSPI_Init() function. This
function includes the MSP layer hardware resources initialization and the
QSPI interface with the external memory.
(#) QSPI memory operations
(++) QSPI memory can be accessed with read/write operations once it is
initialized.
Read/write operation can be performed with AHB access using the functions
BSP_QSPI_Read()/BSP_QSPI_Write().
(++) The function BSP_QSPI_GetInfo() returns the configuration of the QSPI memory.
(see the QSPI memory data sheet)
(++) Perform erase block operation using the function BSP_QSPI_Erase_Block() and by
specifying the block address. You can perform an erase operation of the whole
chip by calling the function BSP_QSPI_Erase_Chip().
(++) The function BSP_QSPI_GetStatus() returns the current status of the QSPI memory.
(see the QSPI memory data sheet)
@endverbatim
******************************************************************************
*/
/* Dependencies
- stm32f7xx_hal_qspi.c
- stm32f7xx_hal_gpio.c
- stm32f7xx_hal_cortex.c
- stm32f7xx_hal_rcc_ex.h
- mx25l512.h
EndDependencies */
/* Includes ------------------------------------------------------------------*/
#include "stm32f769i_discovery_qspi.h"
/** @addtogroup BSP
* @{
*/
/** @addtogroup STM32F769I_DISCOVERY
* @{
*/
/** @defgroup STM32F769I_DISCOVERY_QSPI STM32F769I_DISCOVERY QSPI
* @{
*/
/* Private variables ---------------------------------------------------------*/
/** @defgroup STM32F769I_DISCOVERY_QSPI_Private_Variables STM32F769I_DISCOVERY QSPI Private Variables
* @{
*/
QSPI_HandleTypeDef QSPIHandle;
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup STM32F769I_DISCOVERY_QSPI_Private_Functions STM32F769I_DISCOVERY QSPI Private Functions
* @{
*/
static uint8_t QSPI_ResetMemory(QSPI_HandleTypeDef *hqspi);
static uint8_t QSPI_EnterFourBytesAddress(QSPI_HandleTypeDef *hqspi);
static uint8_t QSPI_DummyCyclesCfg(QSPI_HandleTypeDef *hqspi);
static uint8_t QSPI_EnterMemory_QPI(QSPI_HandleTypeDef *hqspi);
static uint8_t QSPI_ExitMemory_QPI(QSPI_HandleTypeDef *hqspi);
static uint8_t QSPI_OutDrvStrengthCfg(QSPI_HandleTypeDef *hqspi);
static uint8_t QSPI_WriteEnable(QSPI_HandleTypeDef *hqspi);
static uint8_t QSPI_AutoPollingMemReady (QSPI_HandleTypeDef *hqspi, uint32_t Timeout);
/**
* @}
*/
/** @defgroup STM32F769I_DISCOVERY_QSPI_Exported_Functions STM32F769I_DISCOVERY QSPI Exported Functions
* @{
*/
/**
* @brief Initializes the QSPI interface.
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_Init(void)
{
QSPIHandle.Instance = QUADSPI;
/* Call the DeInit function to reset the driver */
if (HAL_QSPI_DeInit(&QSPIHandle) != HAL_OK)
{
return QSPI_ERROR;
}
/* System level initialization */
BSP_QSPI_MspInit(&QSPIHandle, NULL);
/* QSPI initialization */
/* QSPI freq = SYSCLK /(1 + ClockPrescaler) = 216 MHz/(1+1) = 108 Mhz */
QSPIHandle.Init.ClockPrescaler = 1; /* QSPI freq = 216 MHz/(1+1) = 108 Mhz */
QSPIHandle.Init.FifoThreshold = 16;
QSPIHandle.Init.SampleShifting = QSPI_SAMPLE_SHIFTING_HALFCYCLE;
QSPIHandle.Init.FlashSize = POSITION_VAL(MX25L512_FLASH_SIZE) - 1;
QSPIHandle.Init.ChipSelectHighTime = QSPI_CS_HIGH_TIME_4_CYCLE; /* Min 30ns for nonRead */
QSPIHandle.Init.ClockMode = QSPI_CLOCK_MODE_0;
QSPIHandle.Init.FlashID = QSPI_FLASH_ID_1;
QSPIHandle.Init.DualFlash = QSPI_DUALFLASH_DISABLE;
if (HAL_QSPI_Init(&QSPIHandle) != HAL_OK)
{
return QSPI_ERROR;
}
/* QSPI memory reset */
if (QSPI_ResetMemory(&QSPIHandle) != QSPI_OK)
{
return QSPI_NOT_SUPPORTED;
}
/* Put QSPI memory in QPI mode */
if( QSPI_EnterMemory_QPI( &QSPIHandle )!=QSPI_OK )
{
return QSPI_NOT_SUPPORTED;
}
/* Set the QSPI memory in 4-bytes address mode */
if (QSPI_EnterFourBytesAddress(&QSPIHandle) != QSPI_OK)
{
return QSPI_NOT_SUPPORTED;
}
/* Configuration of the dummy cycles on QSPI memory side */
if (QSPI_DummyCyclesCfg(&QSPIHandle) != QSPI_OK)
{
return QSPI_NOT_SUPPORTED;
}
/* Configuration of the Output driver strength on memory side */
if( QSPI_OutDrvStrengthCfg( &QSPIHandle ) != QSPI_OK )
{
return QSPI_NOT_SUPPORTED;
}
return QSPI_OK;
}
/**
* @brief De-Initializes the QSPI interface.
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_DeInit(void)
{
QSPIHandle.Instance = QUADSPI;
/* Put QSPI memory in SPI mode */
if( QSPI_ExitMemory_QPI(&QSPIHandle )!=QSPI_OK )
{
return QSPI_NOT_SUPPORTED;
}
/* Call the DeInit function to reset the driver */
if (HAL_QSPI_DeInit(&QSPIHandle) != HAL_OK)
{
return QSPI_ERROR;
}
/* System level De-initialization */
BSP_QSPI_MspDeInit(&QSPIHandle, NULL);
return QSPI_OK;
}
/**
* @brief Reads an amount of data from the QSPI memory.
* @param pData: Pointer to data to be read
* @param ReadAddr: Read start address
* @param Size: Size of data to read
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_Read(uint8_t* pData, uint32_t ReadAddr, uint32_t Size)
{
QSPI_CommandTypeDef s_command;
/* Initialize the read command */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = QPI_READ_4_BYTE_ADDR_CMD;
s_command.AddressMode = QSPI_ADDRESS_4_LINES;
s_command.AddressSize = QSPI_ADDRESS_32_BITS;
s_command.Address = ReadAddr;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = MX25L512_DUMMY_CYCLES_READ_QUAD_IO;
s_command.NbData = Size;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Configure the command */
if (HAL_QSPI_Command(&QSPIHandle, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Set S# timing for Read command */
MODIFY_REG(QSPIHandle.Instance->DCR, QUADSPI_DCR_CSHT, QSPI_CS_HIGH_TIME_1_CYCLE);
/* Reception of the data */
if (HAL_QSPI_Receive(&QSPIHandle, pData, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Restore S# timing for nonRead commands */
MODIFY_REG(QSPIHandle.Instance->DCR, QUADSPI_DCR_CSHT, QSPI_CS_HIGH_TIME_4_CYCLE);
return QSPI_OK;
}
/**
* @brief Writes an amount of data to the QSPI memory.
* @param pData: Pointer to data to be written
* @param WriteAddr: Write start address
* @param Size: Size of data to write
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_Write(uint8_t* pData, uint32_t WriteAddr, uint32_t Size)
{
QSPI_CommandTypeDef s_command;
uint32_t end_addr, current_size, current_addr;
/* Calculation of the size between the write address and the end of the page */
current_size = MX25L512_PAGE_SIZE - (WriteAddr % MX25L512_PAGE_SIZE);
/* Check if the size of the data is less than the remaining place in the page */
if (current_size > Size)
{
current_size = Size;
}
/* Initialize the address variables */
current_addr = WriteAddr;
end_addr = WriteAddr + Size;
/* Initialize the program command */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = QPI_PAGE_PROG_4_BYTE_ADDR_CMD;
s_command.AddressMode = QSPI_ADDRESS_4_LINES;
s_command.AddressSize = QSPI_ADDRESS_32_BITS;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Perform the write page by page */
do
{
s_command.Address = current_addr;
s_command.NbData = current_size;
/* Enable write operations */
if (QSPI_WriteEnable(&QSPIHandle) != QSPI_OK)
{
return QSPI_ERROR;
}
/* Configure the command */
if (HAL_QSPI_Command(&QSPIHandle, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Transmission of the data */
if (HAL_QSPI_Transmit(&QSPIHandle, pData, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Configure automatic polling mode to wait for end of program */
if (QSPI_AutoPollingMemReady(&QSPIHandle, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != QSPI_OK)
{
return QSPI_ERROR;
}
/* Update the address and size variables for next page programming */
current_addr += current_size;
pData += current_size;
current_size = ((current_addr + MX25L512_PAGE_SIZE) > end_addr) ? (end_addr - current_addr) : MX25L512_PAGE_SIZE;
} while (current_addr < end_addr);
return QSPI_OK;
}
/**
* @brief Erases the specified block of the QSPI memory.
* @param BlockAddress: Block address to erase
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_Erase_Block(uint32_t BlockAddress)
{
QSPI_CommandTypeDef s_command;
/* Initialize the erase command */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = SUBSECTOR_ERASE_4_BYTE_ADDR_CMD;
s_command.AddressMode = QSPI_ADDRESS_4_LINES;
s_command.AddressSize = QSPI_ADDRESS_32_BITS;
s_command.Address = BlockAddress;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_NONE;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Enable write operations */
if (QSPI_WriteEnable(&QSPIHandle) != QSPI_OK)
{
return QSPI_ERROR;
}
/* Send the command */
if (HAL_QSPI_Command(&QSPIHandle, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Configure automatic polling mode to wait for end of erase */
if (QSPI_AutoPollingMemReady(&QSPIHandle, MX25L512_SUBSECTOR_ERASE_MAX_TIME) != QSPI_OK)
{
return QSPI_ERROR;
}
return QSPI_OK;
}
/**
* @brief Erases the entire QSPI memory.
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_Erase_Chip(void)
{
QSPI_CommandTypeDef s_command;
/* Initialize the erase command */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = BULK_ERASE_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_NONE;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Enable write operations */
if (QSPI_WriteEnable(&QSPIHandle) != QSPI_OK)
{
return QSPI_ERROR;
}
/* Send the command */
if (HAL_QSPI_Command(&QSPIHandle, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Configure automatic polling mode to wait for end of erase */
if (QSPI_AutoPollingMemReady(&QSPIHandle, MX25L512_BULK_ERASE_MAX_TIME) != QSPI_OK)
{
return QSPI_ERROR;
}
return QSPI_OK;
}
/**
* @brief Reads current status of the QSPI memory.
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_GetStatus(void)
{
QSPI_CommandTypeDef s_command;
uint8_t reg;
/* Initialize the read flag status register command */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = READ_STATUS_REG_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = 0;
s_command.NbData = 1;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Configure the command */
if (HAL_QSPI_Command(&QSPIHandle, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Reception of the data */
if (HAL_QSPI_Receive(&QSPIHandle, ®, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Check the value of the register*/
if ((reg & MX25L512_SR_WIP) == 0)
{
return QSPI_OK;
}
else
{
return QSPI_BUSY;
}
}
/**
* @brief Return the configuration of the QSPI memory.
* @param pInfo: pointer on the configuration structure
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_GetInfo(QSPI_Info* pInfo)
{
/* Configure the structure with the memory configuration */
pInfo->FlashSize = MX25L512_FLASH_SIZE;
pInfo->EraseSectorSize = MX25L512_SUBSECTOR_SIZE;
pInfo->EraseSectorsNumber = (MX25L512_FLASH_SIZE/MX25L512_SUBSECTOR_SIZE);
pInfo->ProgPageSize = MX25L512_PAGE_SIZE;
pInfo->ProgPagesNumber = (MX25L512_FLASH_SIZE/MX25L512_PAGE_SIZE);
return QSPI_OK;
}
/**
* @brief Configure the QSPI in memory-mapped mode
* @retval QSPI memory status
*/
uint8_t BSP_QSPI_EnableMemoryMappedMode(void)
{
QSPI_CommandTypeDef s_command;
QSPI_MemoryMappedTypeDef s_mem_mapped_cfg;
/* Configure the command for the read instruction */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = QPI_READ_4_BYTE_ADDR_CMD;
s_command.AddressMode = QSPI_ADDRESS_4_LINES;
s_command.AddressSize = QSPI_ADDRESS_32_BITS;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = MX25L512_DUMMY_CYCLES_READ_QUAD_IO;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Configure the memory mapped mode */
s_mem_mapped_cfg.TimeOutActivation = QSPI_TIMEOUT_COUNTER_DISABLE;
s_mem_mapped_cfg.TimeOutPeriod = 0;
if (HAL_QSPI_MemoryMapped(&QSPIHandle, &s_command, &s_mem_mapped_cfg) != HAL_OK)
{
return QSPI_ERROR;
}
return QSPI_OK;
}
/**
* @}
*/
/** @addtogroup STM32F769I_DISCOVERY_QSPI_Private_Functions
* @{
*/
/**
* @brief QSPI MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* - NVIC configuration for QSPI interrupt
* @retval None
*/
__weak void BSP_QSPI_MspInit(QSPI_HandleTypeDef *hqspi, void *Params)
{
GPIO_InitTypeDef gpio_init_structure;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable the QuadSPI memory interface clock */
QSPI_CLK_ENABLE();
/* Reset the QuadSPI memory interface */
QSPI_FORCE_RESET();
QSPI_RELEASE_RESET();
/* Enable GPIO clocks */
QSPI_CS_GPIO_CLK_ENABLE();
QSPI_CLK_GPIO_CLK_ENABLE();
QSPI_D0_GPIO_CLK_ENABLE();
QSPI_D1_GPIO_CLK_ENABLE();
QSPI_D2_GPIO_CLK_ENABLE();
QSPI_D3_GPIO_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* QSPI CS GPIO pin configuration */
gpio_init_structure.Pin = QSPI_CS_PIN;
gpio_init_structure.Alternate = QSPI_CS_PIN_AF;
gpio_init_structure.Mode = GPIO_MODE_AF_PP;
gpio_init_structure.Pull = GPIO_PULLUP;
gpio_init_structure.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(QSPI_CS_GPIO_PORT, &gpio_init_structure);
/* QSPI CLK GPIO pin configuration */
gpio_init_structure.Pin = QSPI_CLK_PIN;
gpio_init_structure.Alternate = QSPI_CLK_PIN_AF;
gpio_init_structure.Pull = GPIO_NOPULL;
HAL_GPIO_Init(QSPI_CLK_GPIO_PORT, &gpio_init_structure);
/* QSPI D0 GPIO pin configuration */
gpio_init_structure.Pin = QSPI_D0_PIN;
gpio_init_structure.Alternate = QSPI_D0_PIN_AF;
HAL_GPIO_Init(QSPI_D0_GPIO_PORT, &gpio_init_structure);
/* QSPI D1 GPIO pin configuration */
gpio_init_structure.Pin = QSPI_D1_PIN;
gpio_init_structure.Alternate = QSPI_D1_PIN_AF;
HAL_GPIO_Init(QSPI_D1_GPIO_PORT, &gpio_init_structure);
/* QSPI D2 GPIO pin configuration */
gpio_init_structure.Pin = QSPI_D2_PIN;
gpio_init_structure.Alternate = QSPI_D2_PIN_AF;
HAL_GPIO_Init(QSPI_D2_GPIO_PORT, &gpio_init_structure);
/* QSPI D3 GPIO pin configuration */
gpio_init_structure.Pin = QSPI_D3_PIN;
gpio_init_structure.Alternate = QSPI_D3_PIN_AF;
HAL_GPIO_Init(QSPI_D3_GPIO_PORT, &gpio_init_structure);
/*##-3- Configure the NVIC for QSPI #########################################*/
/* NVIC configuration for QSPI interrupt */
HAL_NVIC_SetPriority(QUADSPI_IRQn, 0x0F, 0);
HAL_NVIC_EnableIRQ(QUADSPI_IRQn);
}
/**
* @brief QSPI MSP De-Initialization
* This function frees the hardware resources used in this example:
* - Disable the Peripheral's clock
* - Revert GPIO and NVIC configuration to their default state
* @retval None
*/
__weak void BSP_QSPI_MspDeInit(QSPI_HandleTypeDef *hqspi, void *Params)
{
/*##-1- Disable the NVIC for QSPI ###########################################*/
HAL_NVIC_DisableIRQ(QUADSPI_IRQn);
/*##-2- Disable peripherals and GPIO Clocks ################################*/
/* De-Configure QSPI pins */
HAL_GPIO_DeInit(QSPI_CS_GPIO_PORT, QSPI_CS_PIN);
HAL_GPIO_DeInit(QSPI_CLK_GPIO_PORT, QSPI_CLK_PIN);
HAL_GPIO_DeInit(QSPI_D0_GPIO_PORT, QSPI_D0_PIN);
HAL_GPIO_DeInit(QSPI_D1_GPIO_PORT, QSPI_D1_PIN);
HAL_GPIO_DeInit(QSPI_D2_GPIO_PORT, QSPI_D2_PIN);
HAL_GPIO_DeInit(QSPI_D3_GPIO_PORT, QSPI_D3_PIN);
/*##-3- Reset peripherals ##################################################*/
/* Reset the QuadSPI memory interface */
QSPI_FORCE_RESET();
QSPI_RELEASE_RESET();
/* Disable the QuadSPI memory interface clock */
QSPI_CLK_DISABLE();
}
/**
* @brief This function reset the QSPI memory.
* @param hqspi: QSPI handle
* @retval None
*/
static uint8_t QSPI_ResetMemory(QSPI_HandleTypeDef *hqspi)
{
QSPI_CommandTypeDef s_command;
QSPI_AutoPollingTypeDef s_config;
uint8_t reg;
/* Send command RESET command in QPI mode (QUAD I/Os) */
/* Initialize the reset enable command */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = RESET_ENABLE_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_NONE;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Send the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Send the reset memory command */
s_command.Instruction = RESET_MEMORY_CMD;
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Send command RESET command in SPI mode */
/* Initialize the reset enable command */
s_command.InstructionMode = QSPI_INSTRUCTION_1_LINE;
s_command.Instruction = RESET_ENABLE_CMD;
/* Send the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Send the reset memory command */
s_command.Instruction = RESET_MEMORY_CMD;
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* After reset CMD, 1000ms requested if QSPI memory SWReset occured during full chip erase operation */
HAL_Delay( 1000 );
/* Configure automatic polling mode to wait the WIP bit=0 */
s_config.Match = 0;
s_config.Mask = MX25L512_SR_WIP;
s_config.MatchMode = QSPI_MATCH_MODE_AND;
s_config.StatusBytesSize = 1;
s_config.Interval = 0x10;
s_config.AutomaticStop = QSPI_AUTOMATIC_STOP_ENABLE;
s_command.InstructionMode = QSPI_INSTRUCTION_1_LINE;
s_command.Instruction = READ_STATUS_REG_CMD;
s_command.DataMode = QSPI_DATA_1_LINE;
if (HAL_QSPI_AutoPolling(hqspi, &s_command, &s_config, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Initialize the reading of status register */
s_command.InstructionMode = QSPI_INSTRUCTION_1_LINE;
s_command.Instruction = READ_STATUS_REG_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_1_LINE;
s_command.DummyCycles = 0;
s_command.NbData = 1;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Configure the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Reception of the data */
if (HAL_QSPI_Receive(hqspi, ®, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Enable write operations, command in 1 bit */
/* Enable write operations */
s_command.InstructionMode = QSPI_INSTRUCTION_1_LINE;
s_command.Instruction = WRITE_ENABLE_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_NONE;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Configure automatic polling mode to wait for write enabling */
s_config.Match = MX25L512_SR_WREN;
s_config.Mask = MX25L512_SR_WREN;
s_config.MatchMode = QSPI_MATCH_MODE_AND;
s_config.StatusBytesSize = 1;
s_config.Interval = 0x10;
s_config.AutomaticStop = QSPI_AUTOMATIC_STOP_ENABLE;
s_command.Instruction = READ_STATUS_REG_CMD;
s_command.DataMode = QSPI_DATA_1_LINE;
if (HAL_QSPI_AutoPolling(hqspi, &s_command, &s_config, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Update the configuration register with new dummy cycles */
s_command.InstructionMode = QSPI_INSTRUCTION_1_LINE;
s_command.Instruction = WRITE_STATUS_CFG_REG_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_1_LINE;
s_command.DummyCycles = 0;
s_command.NbData = 1;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Enable the Quad IO on the QSPI memory (Non-volatile bit) */
reg |= MX25L512_SR_QUADEN;
/* Configure the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Transmission of the data */
if (HAL_QSPI_Transmit(hqspi, ®, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* 40ms Write Status/Configuration Register Cycle Time */
HAL_Delay( 40 );
return QSPI_OK;
}
/**
* @brief This function set the QSPI memory in 4-byte address mode
* @param hqspi: QSPI handle
* @retval None
*/
static uint8_t QSPI_EnterFourBytesAddress(QSPI_HandleTypeDef *hqspi)
{
QSPI_CommandTypeDef s_command;
/* Initialize the command */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = ENTER_4_BYTE_ADDR_MODE_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_NONE;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Enable write operations */
if (QSPI_WriteEnable(hqspi) != QSPI_OK)
{
return QSPI_ERROR;
}
/* Send the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Configure automatic polling mode to wait the memory is ready */
if (QSPI_AutoPollingMemReady(hqspi, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != QSPI_OK)
{
return QSPI_ERROR;
}
return QSPI_OK;
}
/**
* @brief This function configure the dummy cycles on memory side.
* @param hqspi: QSPI handle
* @retval None
*/
static uint8_t QSPI_DummyCyclesCfg(QSPI_HandleTypeDef *hqspi)
{
QSPI_CommandTypeDef s_command;
uint8_t reg[2];
/* Initialize the reading of status register */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = READ_STATUS_REG_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = 0;
s_command.NbData = 1;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Configure the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Reception of the data */
if (HAL_QSPI_Receive(hqspi, &(reg[0]), HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Initialize the reading of configuration register */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = READ_CFG_REG_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = 0;
s_command.NbData = 1;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Configure the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Reception of the data */
if (HAL_QSPI_Receive(hqspi, &(reg[1]), HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Enable write operations */
if (QSPI_WriteEnable(hqspi) != QSPI_OK)
{
return QSPI_ERROR;
}
/* Update the configuration register with new dummy cycles */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = WRITE_STATUS_CFG_REG_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = 0;
s_command.NbData = 2;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* MX25L512_DUMMY_CYCLES_READ_QUAD = 3 for 10 cycles in QPI mode */
MODIFY_REG( reg[1], MX25L512_CR_NB_DUMMY, (MX25L512_DUMMY_CYCLES_READ_QUAD << POSITION_VAL(MX25L512_CR_NB_DUMMY)));
/* Configure the write volatile configuration register command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Transmission of the data */
if (HAL_QSPI_Transmit(hqspi, &(reg[0]), HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* 40ms Write Status/Configuration Register Cycle Time */
HAL_Delay( 40 );
return QSPI_OK;
}
/**
* @brief This function put QSPI memory in QPI mode (quad I/O).
* @param hqspi: QSPI handle
* @retval None
*/
static uint8_t QSPI_EnterMemory_QPI( QSPI_HandleTypeDef *hqspi )
{
QSPI_CommandTypeDef s_command;
QSPI_AutoPollingTypeDef s_config;
/* Initialize the QPI enable command */
/* QSPI memory is supported to be in SPI mode, so CMD on 1 LINE */
s_command.InstructionMode = QSPI_INSTRUCTION_1_LINE;
s_command.Instruction = ENTER_QUAD_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_NONE;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Send the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
/* Configure automatic polling mode to wait the QUADEN bit=1 and WIP bit=0 */
s_config.Match = MX25L512_SR_QUADEN;
s_config.Mask = MX25L512_SR_QUADEN|MX25L512_SR_WIP;
s_config.MatchMode = QSPI_MATCH_MODE_AND;
s_config.StatusBytesSize = 1;
s_config.Interval = 0x10;
s_config.AutomaticStop = QSPI_AUTOMATIC_STOP_ENABLE;
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = READ_STATUS_REG_CMD;
s_command.DataMode = QSPI_DATA_4_LINES;
if (HAL_QSPI_AutoPolling(hqspi, &s_command, &s_config, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
return QSPI_OK;
}
/**
* @brief This function put QSPI memory in SPI mode.
* @param hqspi: QSPI handle
* @retval None
*/
static uint8_t QSPI_ExitMemory_QPI( QSPI_HandleTypeDef *hqspi)
{
QSPI_CommandTypeDef s_command;
/* Initialize the QPI enable command */
/* QSPI memory is supported to be in QPI mode, so CMD on 4 LINES */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = EXIT_QUAD_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_NONE;
s_command.DummyCycles = 0;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Send the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{
return QSPI_ERROR;
}
return QSPI_OK;
}
/**
* @brief This function configure the Output driver strength on memory side.
* @param hqspi: QSPI handle
* @retval None
*/
static uint8_t QSPI_OutDrvStrengthCfg( QSPI_HandleTypeDef *hqspi )
{
QSPI_CommandTypeDef s_command;
uint8_t reg[2];
/* Initialize the reading of status register */
s_command.InstructionMode = QSPI_INSTRUCTION_4_LINES;
s_command.Instruction = READ_STATUS_REG_CMD;
s_command.AddressMode = QSPI_ADDRESS_NONE;
s_command.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE;
s_command.DataMode = QSPI_DATA_4_LINES;
s_command.DummyCycles = 0;
s_command.NbData = 1;
s_command.DdrMode = QSPI_DDR_MODE_DISABLE;
s_command.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
s_command.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/* Configure the command */
if (HAL_QSPI_Command(hqspi, &s_command, HAL_QPSI_TIMEOUT_DEFAULT_VALUE) != HAL_OK)
{