diff --git a/config/zooz/zen21v2.xml b/config/zooz/zen21v2.xml index ee5ecd388c..ce33cb9c39 100644 --- a/config/zooz/zen21v2.xml +++ b/config/zooz/zen21v2.xml @@ -1,50 +1,155 @@ - - - - - Controls the on/off orientation of the rocker switch - - - - - - Control the LED indicator on switch - - - - - - - Use this parameter to enable or disable the auto turn-off timer function - - - - - Use this parameter to set the time after which you want the switch to automatically turn off once it has been turned on. The number entered as value corresponds to the number of minutes - - - Use this parameter to enable or disable the auto turn-off timer function - - - - - Use this parameter to set the time after which you want the switch to automatically turn on once it has been turned off. The number entered as value corresponds to the number of minutes - - - Set the on off status for switch after power failure - - - - - + + + http://www.openzwave.com/device-database/027a:1e1c:b111 + images/zooz/zen21.png + https://products.z-wavealliance.org/products/3667?selectedFrequencyId=2 + If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset. +NOTE: All previously recorded activity and custom settings will be erased from the device’s memory. + 1. Bring your Z-Wave gateway (hub) close to the switch if possible +2. Put the Z-Wave hub into exclusion mode (not sure how to do that? +ask@getzooz.com) +3. Tap the lower paddle on the switch 3 times quickly + 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. +2. Tap the upper paddle on the switch 3 times quickly. + U.S. / Canada / Mexico + ZEN21 + https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3667/zooz-z-wave-plus-on-off-switch-zen21-ver3.1-manual.pdf + Z-WAVE PLUS ON / OFF LIGHT SWITCH + FEATURES: +- Manual and remote on/off control for lights and small appliances +- Unique Direct 3-Way Solution: no add-on switch needed, extra savings! (Neutral wire required, use in 4-Way only if direct connection to load and line are in the same box) +- Scene control on selected hubs +- Reports on/off status to your controller instantly +- NEW VERSION: more advanced settings (timer, turn switch on/off with any paddle, choose state after power failure), improved manual and packaging +- White (no other color available) +- Restores on/off status after power failure +- Can be associated with other Z-Wave devices by scheduling scenes and customizing events +- Compatible with LED, CFL, and incandescent bulbs +- Screw terminal installation - requires Line (Hot), Load, Neutral, and Ground wires +- New and improved Z-Wave Plus 500 series chip for faster, stronger wireless connectivity +- Built-in repeater that strengthens your Z-Wave network +- Blue LED indicator to easily locate the switch in the dark and signal Z-Wave communication +- Use a standard-size wall plate for single gang installations (wall plate not included) +- UL-listed and Z-Wave Plus certified - - - - - - - +SPECIFICATIONS: +- Model Number: ZEN21 + +- Z-Wave Frequency: 908.42 MHz (US) +- Power: 120 VAC, 60 Hz +- Maximum Loads: 960W Incandescent, 150W LED and CFL bulbs, 1800W (15A) Resistive +- Z-Wave Range: Up to 100 feet line of sight between the Wireless Controller and the closest Z-Wave receiver module +- Operating Temperature: 32-104° F (0-40° C) +- Installation: Indoor use only + +https://www.support.getzooz.com/kb/article/316-zooz-on-off-switch-zen21-ver-3-04-advanced-settings/ +MANUAL CONTROL +Upper Paddle: +1 x tap: load on; Scene 1, attribute 00 (button 1) +2 x tap: Scene 1, attribute 03 (button 3) +3 x tap: enter inclusion (pairing) mode; Scene 1, attribute 04 (button 5) +4 x tap: Scene 1, attribute 05 (button 7) +6 x tap: change LED indicator mode (see parameter 2) +10 x tap: change physical / Z-Wave control mode (see parameter 11) +tap-tap-tap-and-hold: factory reset + +Lower Paddle: +1 x tap: load off; Scene 2, attribute 00 (button 2) +2 x tap: Scene 2, attribute 03 (button 4) +3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04 (button 6) +4 x tap: Scene 2, attribute 05 (button 8) +tap-tap-tap-and-hold: factory reset + + + Updated for firmware version 3.04 + + + + + + Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. + + + + + + LED Indication light function. Normal has the LED Indication on when the switch is off, off when the switch is on. + + + + + + + + + + + + Time, in minutes, for auto-off timer delay. + + + + + + + + Set the time (in minutes) after which you want the switch to automatically turn on once it has been turned off. + + + Choose which physical and Z-Wave triggers should prompt the switch to send a status change report to associated devices. + + + + + + + + + + + + + + + + + + + Status after power failure. Off: always turn light off. On: always turn light on. Restore: remember the latest state and restore that state. + + + + + + Enable or Disable scene control functionality for quick double tap triggers (Available for select hubs only). + + + + + Enable or disable local on/off control. If enabled, you’ll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles. + + + + + + Choose the type of 3-way switch you want to use with this dimmer in a 3-way set-up. Changing this setting can allow you to control brightness and dim the light from both 3-way locations. Use a regular momentary switch (like the Zooz ZAC99 accessory switch) if value is set to 2. + + + + + Set reporting behavior for disabled physical control. + + + + + + + + + + + + diff --git a/config/zooz/zen22v2.xml b/config/zooz/zen22v2.xml index 70170f17ac..6b88e43a2f 100644 --- a/config/zooz/zen22v2.xml +++ b/config/zooz/zen22v2.xml @@ -1,34 +1,195 @@ - - - - - Controls the on/off orientation of the rocker switch - - - - - Choose if you want the LED indicator to turn on when switch is on or off - - - - - Enable or disable LED indicator so it stays off at all times - - - - - Choose how fast you want to turn the light on and off - - - - + + + http://www.openzwave.com/device-database/027a:1f1c:b112 + images/zooz/zen22.png + https://products.z-wavealliance.org/products/1946?selectedFrequencyId=2 + If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset. +NOTE: All previously recorded activity and custom settings will be erased from the device’s memory. + 1. Bring your Z-Wave gateway (hub) close to the switch if possible +2. Put the Z-Wave hub into exclusion mode (not sure how to do that? +ask@getzooz.com) +3. Tap the lower paddle on the switch 3 times quickly + 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. +2. Tap the upper paddle on the switch 3 times quickly. + U.S. / Canada / Mexico + ZEN22 + https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/1946/zooz-z-wave-plus-dimmer-switch-zen22-manual.pdf + Zooz Z-Wave Dimmer Light Switch + FEATURES: +- Manual and wireless control from your smart phone or computer (when synced with a Z-Wave gateway controller) +- Direct 3-Way Solution: connects to an existing light switch for 2-point control, no special companion switch needed! (Neutral wire required, on/off control only from slave switch, use in 4-Way only if direct connection to load and line are in the same box) +- NEW IN VER. 3.0: Double tap to full brightness, fully adjustable ramp rate, scene control on select hubs, and more! +- White (no other color available) +- Extended LED bulb compatibility - works with most popular dimmable LED's (including Cree, Ecosmart, Philips, GE, Sylvania, Sunco, and others. NOT COMPATIBLE WITH LUMINUS BULBS.) +- Quick status reports to your hub when operated manually +- Based on universal command classes - supported by all certified Z-Wave gateway controllers +- Capable of advanced automation and association with other Z-Wave devices — schedule custom scenes and events +- Upgraded Z-Wave Plus 500 series chip for stronger and faster wireless connectivity +- Built-in signal repeater for a more reliable Z-Wave network +- Blue LED indicator to help locate the switch in the dark (now configurable straight from the switch!) +- Fits a standard-size face plate for single and multi gang installations (face plate not included) +- UL-listed and Z-Wave Plus certified - - - - - - +SPECIFICATIONS: +- Model Number: ZEN22 + +- Z-Wave Signal Frequency: 908.42 MHz +- Power: 120 VAC, 60 Hz +- Maximum Load: 500W Single-gang, 400W Double-gang, 300W Triple-gang Incandescent, 150W CFL or LED +- Range: Up to 100 feet line of sight +- Operating Temperature: 32-104° F (0-40° C) +- Installation and Use: Indoor only + +https://www.support.getzooz.com/kb/article/319-zooz-dimmer-zen22-ver-3-07-advanced-settings/ +MANUAL CONTROL +Upper Paddle: +1 x tap: load on to last / custom brightness; Scene 1, attribute 00 (button 1) +2 x tap: on to full / max brightness; Scene 1, attribute 03 (button 3) +3 x tap: enter inclusion (pairing) mode; Scene 1, attribute 04 (button 5) +4 x tap: Scene 1, attribute 05 (button 7) +6 x tap: change LED indicator mode (see parameter 2) +10 x tap: change physical / Z-Wave control mode (see parameter 15) +press and hold: increase brightness level +tap-tap-tap-and-hold: factory reset + +Lower Paddle: +1 x tap: load off; Scene 2, attribute 00 (button 2) +2 x tap: Scene 2, attribute 03 (button 4) +3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04 (button 6) +4 x tap: Scene 2, attribute 05 (button 8) +press and hold: decrease brightness level +tap-tap-tap-and-hold: factory reset + + + Updated for firmware version 3.07 + + + + + + Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. + + + + + + LED Indication light function. Normal has the LED Indication on when the switch is off, off when the switch is on. + + + + + + + + + + + + Time, in minutes, for auto-off timer delay. + + + + + + + + Set the time (in minutes) after which you want the switch to automatically turn on once it has been turned off. + + + Choose which physical and Z-Wave triggers should prompt the switch to send a status change report to associated devices. + + + + + + + + + + + + + + + + + + + Status after power failure. Off: always turn light off. On: always turn light on. Restore: remember the latest state and restore that state. + + + + + + Adjust the physical ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. This setting is for physical taps only, see parameter 17 to adjust Z-Wave ramp rate. Values: 1 – 99 (seconds). 0 – instant on/off. Default: 1 + + + Set the minimum brightness level (in %) for your dimmer. You won’t be able to dim the light below the set value. Default: 1 + + + Set the maximum brightness level (in %) for your dimmer. You won’t be able to add brightness to the light beyond the set value. Note: if Parameter 12 is set to value 0, Parameter 11 is automatically disabled. Default: 99 + + + Double Tap action. When set to Full, turns light on to 100%. If set to Maximum Level, turns light on to % set in Parameter 11. + + + + + Enable or Disable scene control functionality for quick double tap triggers. + + + + + Enables/Disables the double-tap function and assign brightness to single tap. Last level: single tap returns to last brightness level. Full/Max level: single tap returns to full/max level + + + + + + Enable or disable local on/off control. If enabled, you’ll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles. + + + + + + Set the time it takes to get from 0% to 100% brightness when pressing and holding the paddle (physical dimming). The number entered as value corresponds to the number of seconds. Default: 4 + + + Choose if you want to set the Z-Wave ramp rate independently of the physical ramp rate (using an appropriate command in your hub) or if you want them to match. + + + + + Set the custom brightness level (instead of the last set brightness level) you want the dimmer to come on to when you single tap the upper paddle. Default: 0 - last brightness level + + + Choose the type of 3-way switch you want to use with this dimmer in a 3-way set-up. Changing this setting can allow you to control brightness and dim the light from both 3-way locations. Use a regular momentary switch (like the Zooz ZAC99 accessory switch) if value is set to 2. + + + + + + + Choose how you'd like the dimmer to report when paddles are tapped and held and physical / Z-Wave control is enabled or disabled. + + + + + Set reporting behavior for disabled physical control. + + + + + Set the brightness level the dimmer will turn on to when off and when lower paddle is held DOWN for a second. Default: 20 + + + + + + + + + diff --git a/config/zooz/zen26.xml b/config/zooz/zen26.xml index 5d1162b8c2..891766d1fc 100644 --- a/config/zooz/zen26.xml +++ b/config/zooz/zen26.xml @@ -1,24 +1,24 @@ - - - http://www.openzwave.com/device-database/027A:A001:A000 - images/zooz/zen26.png - https://products.z-wavealliance.org/products/3147/ - If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset. +--> + + http://www.openzwave.com/device-database/027A:A001:A000 + images/zooz/zen26.png + https://products.z-wavealliance.org/products/3147/ + If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory. - 1. Bring your Z-Wave gateway (hub) close to the switch if possible + 1. Bring your Z-Wave gateway (hub) close to the switch if possible 2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) 3. Tap the lower paddle on the switch 3 times quickly - 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. + 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. 2. Tap the upper paddle on the switch 3 times quickly. - U.S. / Canada / Mexico - ZEN26 - https://Products.Z-WaveAlliance.org/ProductManual/File?folder=&filename=Manuals/3147/zooz-z-wave-plus-s2-on-off-switch-zen26-manual.pdf - S2 On Off Switch - FEATURES: + U.S. / Canada / Mexico + ZEN26 + https://Products.Z-WaveAlliance.org/ProductManual/File?folder=&filename=Manuals/3147/zooz-z-wave-plus-s2-on-off-switch-zen26-manual.pdf + S2 On Off Switch + FEATURES: - Manual or Z-Wave on/off control with instant status updates - Simple Direct 3-Way: connect with existing on/off switches in 3-way, 4-way, and 5-way set-ups, no add-on needed (neutral wire required) - Remembers and restores on/off status after power failure @@ -35,65 +35,110 @@ SPECIFICATIONS: - Maximum Load: 8 A, 150 W LED/CFL, 600 W incandescent, 1200 W resistive - Range: Up to 100 feet line of sight - Operating Temperature: 32-104° F (0-40° C) -- Installation and Use: Indoor only - - Initial Metadata Import from Z-Wave Alliance Database - https://products.z-wavealliance.org/products/3147/xml - Updated for firmware version 2.0 - - - - - - Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. - - - - - - LED Indication light function. Normal has the LED Indication on when the switch is off, off when the switch is on. - - - - - - - - - - - - Time, in minutes, for auto-off timer delay. - - - - - - - - Set the time (in minutes) after which you want the switch to automatically turn on once it has been turned off. - - - Status after power failure. Off: always turn light off. On: always turn light on. Restore: remember the latest state and restore that state. - - - - - - Enable or Disable scene control functionality for quick double tap triggers (Available for select hubs only). - - - - - If enabled, you'll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles. - - - - - - - - - - - +- Installation and Use: Indoor only + +https://www.support.getzooz.com/kb/article/315-zooz-s2-on-off-switch-zen26-ver-2-03-advanced-settings/ +MANUAL CONTROL +Upper Paddle: +1 x tap: load on; Scene 1, attribute 00 (button 1) +2 x tap: Scene 1, attribute 03 (button 3) +3 x tap: enter inclusion (pairing) mode; Scene 1, attribute 04 (button 5) +4 x tap: Scene 1, attribute 05 (button 7) +6 x tap: change LED indicator mode (see parameter 2) +10 x tap: change physical / Z-Wave control mode (see parameter 11) +tap-tap-tap-and-hold: factory reset + +Lower Paddle: +1 x tap: load off; Scene 2, attribute 00 (button 2) +2 x tap: Scene 2, attribute 03 (button 4) +3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04 (button 6) +4 x tap: Scene 2, attribute 05 (button 8) +tap-tap-tap-and-hold: factory reset + + + Initial Metadata Import from Z-Wave Alliance Database - https://products.z-wavealliance.org/products/3147/xml + Updated for firmware version 2.0 + Updated for firmware version 2.03 + + + + + + Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. + + + + + + LED Indication light function. Normal has the LED Indication on when the switch is off, off when the switch is on. + + + + + + + + + + + + Time, in minutes, for auto-off timer delay. + + + + + + + + Set the time (in minutes) after which you want the switch to automatically turn on once it has been turned off. + + + Choose which physical and Z-Wave triggers should prompt the switch to send a status change report to associated devices. + + + + + + + + + + + + + + + + + + + Status after power failure. Off: always turn light off. On: always turn light on. Restore: remember the latest state and restore that state. + + + + + + Enable or Disable scene control functionality for quick double tap triggers (Available for select hubs only). + + + + + Enable or disable local on/off control. If enabled, you’ll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles. + + + + + + Set reporting behavior for disabled physical control. + + + + + + + + + + + diff --git a/config/zooz/zen27.xml b/config/zooz/zen27.xml index b81b58814a..361a845a4d 100644 --- a/config/zooz/zen27.xml +++ b/config/zooz/zen27.xml @@ -1,10 +1,21 @@ - - - http://www.openzwave.com/device-database/027a:a002:a000 - images/zooz/zen27.png - https://products.z-wavealliance.org/products/3148 - Product features: + + + http://www.openzwave.com/device-database/027a:a002:a000 + images/zooz/zen27.png + https://products.z-wavealliance.org/products/3148 + If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset. + NOTE: All previously recorded activity and custom settings will be erased from the device’s memory. + 1. Bring your Z-Wave gateway (hub) close to the switch if possible +2. Put the Z-Wave hub into exclusion mode (not sure how to do that? +ask@getzooz.com) +3. Tap the lower paddle on the switch 3 times quickly + 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. 2. Tap the upper paddle on the switch 3 times quickly. + U.S. / Canada / Mexico + ZEN27 + https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3148/zooz-z-wave-plus-s2-dimmer-switch-zen27-manual.pdf + S2 Dimmer + Product features: - Manual or Z-Wave on/off and brightness control - Simple Direct 3-Way: connect with existing on/off switches in 3-way, 4-way, and 5-way set-ups, no add-on needed (neutral wire required) - Fully adjustable ramp rate for just the right on/off speed @@ -25,101 +36,153 @@ both sides of heat sink tabs off) - Range: Up to 100 feet line of sight - Operating Temperature: 32-104° F (0-40° C) - Installation and Use: Indoor only - - https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3148/zooz-z-wave-plus-s2-dimmer-switch-zen27-manual.pdf - U.S. / Canada / Mexico - S2 Dimmer - 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. 2. Tap the upper paddle on the switch 3 times quickly. - - ZEN27 - If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, tap-tap-tap’n’hold the upper paddle for at least 10 seconds. The LED indicator will flash to confirm successful reset. - NOTE: All previously recorded activity and custom settings will be erased from the device’s memory. - - 1. Bring your Z-Wave gateway (hub) close to the switch if possible -2. Put the Z-Wave hub into exclusion mode (not sure how to do that? -ask@getzooz.com) -3. Tap the lower paddle on the switch 3 times quickly - - Initial Metadata Import from Z-Wave Alliance Database - https://products.z-wavealliance.org/products/3148/xml - this requires v2.0 (or newer) firmware - - - +https://www.support.getzooz.com/kb/article/314-zooz-s2-dimmer-zen27-ver-2-08-advanced-settings/ +MANUAL CONTROL +Upper Paddle: +1 x tap: load on to last / custom brightness; Scene 1, attribute 00 (button 1) +2 x tap: on to full / max brightness; Scene 1, attribute 03 (button 3) +3 x tap: enter inclusion (pairing) mode; Scene 1, attribute 04 (button 5) +4 x tap: Scene 1, attribute 05 (button 7) +6 x tap: change LED indicator mode (see parameter 2) +10 x tap: change physical / Z-Wave control mode (see parameter 15) +press and hold: increase brightness level +tap-tap-tap-and-hold: factory reset + +Lower Paddle: +1 x tap: load off; Scene 2, attribute 00 (button 2) +2 x tap: Scene 2, attribute 03 (button 4) +3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04 (button 6) +4 x tap: Scene 2, attribute 05 (button 8) +press and hold: decrease brightness level +tap-tap-tap-and-hold: factory reset + + + Initial Metadata Import from Z-Wave Alliance Database - https://products.z-wavealliance.org/products/3148/xml - this requires v2.0 (or newer) firmware + Updated for firmware version 2.08 + + + + - - - - Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. - - - - - - LED Indication light function. Normal has the LED Indication on when the switch is off, off when the switch is on. - - - - - - - - - - - - Time, in minutes, for auto-off timer delay. - - - - - - - - Set the time (in minutes) after which you want the switch to automatically turn on once it has been turned off. - - - Status after power failure. Off: always turn light off. On: always turn light on. Restore: remember the latest state and restore that state. - - - - - - Adjust the ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. - - - Set the minimum brightness level (in %) for your dimmer. You won't be able to dim the light below the set value. - - - Set the maximum brightness level (in %) for your dimmer. You won't be able to add brightness to the light beyond the set value. Note: if Parameter 12 is set to value "Full", Parameter 11 is automatically disabled. - - - Double Tap action. When set to Full, turns light on to 100%. If set to Maximum Level, turns light on to % set in Parameter 11. - - - - - Enable or Disable scene control functionality for quick double tap triggers. - - - - - Enables/Disables the double-tap fucntion and assign brightness to single tap. Last level: single tap returns to last brightness level. Full/Max level: single tap returns to full/max level - - - - - - If enabled, you'll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles. - - - - + + + + Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. + + + + + + LED Indication light function. Normal has the LED Indication on when the switch is off, off when the switch is on. + + + + + + + + + + + + Time, in minutes, for auto-off timer delay. + + + + + + + + Set the time (in minutes) after which you want the switch to automatically turn on once it has been turned off. + + + Choose which physical and Z-Wave triggers should prompt the switch to send a status change report to associated devices. + + + + + + + + + + + + + + + + + + + Status after power failure. Off: always turn light off. On: always turn light on. Restore: remember the latest state and restore that state. + + + + + + Adjust the physical ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. This setting is for physical taps only, see parameter 17 to adjust Z-Wave ramp rate. + + + Set the minimum brightness level (in %) for your dimmer. You won't be able to dim the light below the set value. + + + Set the maximum brightness level (in %) for your dimmer. You won't be able to add brightness to the light beyond the set value. Note: if Parameter 12 is set to value "Full", Parameter 11 is automatically disabled. + + + Double Tap action. When set to Full, turns light on to 100%. If set to Maximum Level, turns light on to % set in Parameter 11. + + + + + Enable or Disable scene control functionality for quick double tap triggers. + + + + + Enables/Disables the double-tap function and assign brightness to single tap. Last level: single tap returns to last brightness level. Full/Max level: single tap returns to full/max level + + + + + + Enable or disable local on/off control. If enabled, you’ll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles. + + + + + + Set the time it takes to get from 0% to 100% brightness when pressing and holding the paddle (physical dimming). The number entered as value corresponds to the number of seconds. Default: 4 + + + Choose if you want to set the Z-Wave ramp rate independently of the physical ramp rate (using an appropriate command in your hub) or if you want them to match. + + + + + Set the custom brightness level (instead of the last set brightness level) you want the dimmer to come on to when you single tap the upper paddle. Default: 0 - last brightness level + + + Choose how you'd like the dimmer to report when paddles are tapped and held and physical / Z-Wave control is enabled or disabled. + + + + + Set reporting behavior for disabled physical control. + + + + + Set the brightness level the dimmer will turn on to when off and when lower paddle is held DOWN for a second. Default: 20 + + - - - - - - - + + + + + + + diff --git a/config/zooz/zen30.xml b/config/zooz/zen30.xml index 0c2c7b6beb..ff3add27e3 100644 --- a/config/zooz/zen30.xml +++ b/config/zooz/zen30.xml @@ -1,7 +1,7 @@ - - - Double Switch - PRODUCT FEATURES: + + + Double Switch + PRODUCT FEATURES: - Manual or Z-Wave control of 2 separate loads (dimmer + relay) - Perfect replacement for a fan / light combo (neutral wire required) - Scene control for multi-tap scenarios on select hubs @@ -9,7 +9,7 @@ - 4-color LED indicator and air-gap switch for added safety - Fully customizable dimming features including ramp rate, on brightness level, and double tap to full brightness -- Remembers and restores on/off status a􀈇er power failure +- Remembers and restores on/off status after power failure - Built-in Z-Wave Plus signal repeater to extend network range - S2 security protocol and 500 Z-Wave chip @@ -21,148 +21,163 @@ SPECIFICATIONS: - Relay Max Load: 15 A (1/2 HP) - Operating Temperature: 32-104° F (0-40° C) - Installation and Use: Indoor only - - http://www.openzwave.com/device-database/027a:a008:a000 - http://www.getzooz.com/ - http://www.support.getzooz.com/kb/section/134 - images/zooz/zen30.png - https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3791/zooz-s2-double-switch-zen30-ver1-manual-online.pdf - 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. 2. Tap the upper paddle on the switch 3 times quickly. - 1. Bring your Z-Wave gateway (hub) close to the switch if possible. -2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) + + http://www.openzwave.com/device-database/027a:a008:a000 + http://www.getzooz.com/ + http://www.support.getzooz.com/kb/section/134 + images/zooz/zen30.png + https://products.z-wavealliance.org/ProductManual/File?folder=&filename=product_documents/3791/zooz-s2-double-switch-zen30-ver1-manual-online.pdf + 1. Initiate inclusion (pairing) in the app (or web interface) of your hub. 2. Tap the upper paddle on the switch 3 times quickly. + 1. Bring your Z-Wave gateway (hub) close to the switch if possible. +2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) 3. Tap the lower paddle on the switch 3 times quickly 4. Your hub will confirm exclusion and the device will disappear from your controller's device list - If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, press and hold the lower paddle on the dimmer for at least 15 seconds until the LED indicators start flashing, then release. Then immediately press and hold the upper paddle on the dimmer for at least 15 seconds. The LED indicators will flash again to confirm successful reset. - https://products.z-wavealliance.org/products/3791 - U.S. / Canada / Mexico - ZEN30 - - Initial Metadata Import - - + If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, press and hold the lower paddle on the dimmer for at least 15 seconds until the LED indicators start flashing, then release. Then immediately press and hold the upper paddle on the dimmer for at least 15 seconds. The LED indicators will flash again to confirm successful reset. + https://products.z-wavealliance.org/products/3791 + U.S. / Canada / Mexico + ZEN30 + + Initial Metadata Import + Updated for firmware version 1.04 + + - - - - LED Indicator Mode for Dimmer. Normal has the dimmer (top) LED indication on when the switch is off, off when the switch is on. Default: Normal - - - - - - - LED Indicator Mode for Relay. Normal has the relay (bottom) LED indication on when the switch is off, off when the switch is on. Default: Normal - - - - - - - LED Indicater color for Dimmer. White, Blue, Green or Red. Default: White - - - - - - - LED Indicater color for Relay. White, Blue, Green or Red. Default: White - - - - - - - LED Indicater Brightness for Dimmer. Bright (100%), Medium (60%) or Low (30%). Default: Medium - - - - - - LED Indicater Brightness for Relay. Bright (100%), Medium (60%) or Low (30%). Default: Medium - - - - - - LED Indicator Mode for Scene Control. Enable/Disable LED indicators next to the dimmer lighting up when a scene is selected. Default: disabled - - - - - Auto Turn-Off Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) - - - Auto Turn-On Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) - - - Auto Turn-Off Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) - - - Auto Turn-On Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) - - - On Off Status After Power Failure. Default: Restore both to prior state - - - - - - - - - - - - Ramp Rate Control for Dimmer. Adjust the ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. Note that 0 is instant. Default: 1 - - - Minimum Brightness. Set the minimum brightness level (in %) for your dimmer. You won't be able to dim the light below the set value. Default: 1 - - - Maximum Brightness. Set the maximum brightness level (in %) for your dimmer. You won't be able to add brightness to the light beyond the set value. Default: 99 - - - Double Tap Function for Dimmer. When set to full, turns light on to 100%. If set to maximum level, turns light on to % set in Parameter 15. Default: full - - - - - Enable/Disable Double-tap for Dimmer. Enables/Disables the double-tap fucntion and assign brightness to single tap. enabled: single tap turns on to maximum brightness level. disabled (last level): single tap returns to last brightness level. disabled (full/max level): single tap returns to full brightmess. Default: enabled - - - - - - Enable/Disable Load Control for Dimmer (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the dimmer will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled - - - - - - Enable/Disable Load Control for Relay (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the relay will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled - - - - - - Choose how many seconds it takes for the dimmer to go from 0% to 100% brightness when pressing and holding the paddle. Default: 4. - - - Z-Wave Ramp Rate for Dimmer. Choose if you would like to match the Z-Wave on/off ramp rate with the manual ramp rate or set it separately on your own. Default: match. - - - - - Default Brightness Level On for Dimmer. Set custom brightness level (in %) for the dimmer to come on to at single tap. Choose 0 for last brightness level. Default: 0. - - + + + + LED Indicator Mode for Dimmer. Normal has the dimmer (top) LED indication on when the switch is off, off when the switch is on. Default: Normal + + + + + + + LED Indicator Mode for Relay. Normal has the relay (bottom) LED indication on when the switch is off, off when the switch is on. Default: Normal + + + + + + + LED Indicater color for Dimmer. White, Blue, Green or Red. Default: White + + + + + + + LED Indicater color for Relay. White, Blue, Green or Red. Default: White + + + + + + + LED Indicater Brightness for Dimmer. Bright (100%), Medium (60%) or Low (30%). Default: Medium + + + + + + LED Indicater Brightness for Relay. Bright (100%), Medium (60%) or Low (30%). Default: Medium + + + + + + LED Indicator Mode for Scene Control. Enable/Disable LED indicators next to the dimmer lighting up when a scene is selected. Default: disabled + + + + + Auto Turn-Off Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) + + + Auto Turn-On Timer for Dimmer. Sets the time (in minutes) after which you want the dimmer to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) + + + Auto Turn-Off Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn off once it has been turned on. Range: 1-65535. Default: 0 (disabled) + + + Auto Turn-On Timer for Relay. Sets the time (in minutes) after which you want the relay to automatically turn on once it has been turned off. Range: 1-65535. Default: 0 (disabled) + + + On Off Status After Power Failure. Default: Restore both to prior state + + + + + + + + + + + + Ramp Rate Control for Dimmer. Adjust the ramp rate for your dimmer (fade-in / fade-out effect for on / off operation). Values correspond to the number of seconds it take for the dimmer to reach full brightness or turn off when operated manually. Note that 0 is instant. Default: 1 + + + Minimum Brightness. Set the minimum brightness level (in %) for your dimmer. You won't be able to dim the light below the set value. Default: 1 + + + Maximum Brightness. Set the maximum brightness level (in %) for your dimmer. You won't be able to add brightness to the light beyond the set value. Default: 99 + + + Double Tap Function for Dimmer. When set to full, turns light on to 100%. If set to maximum level, turns light on to % set in Parameter 15. Default: full + + + + + Enable/Disable Double-tap for Dimmer. Enables/Disables the double-tap fucntion and assign brightness to single tap. enabled: single tap turns on to maximum brightness level. disabled (last level): single tap returns to last brightness level. disabled (full/max level): single tap returns to full brightmess. Default: enabled + + + + + + Enable/Disable Load Control for Dimmer (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the dimmer will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled + + + + + + Enable/Disable Load Control for Relay (Smart Bulb Setting). Enable or disable direct manual and Z-Wave control of the connected light (works great for smart bulb control). If disabled, the relay will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you cn use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through the paddles. Default: manual disabled + + + + + + Choose how many seconds it takes for the dimmer to go from 0% to 100% brightness when pressing and holding the paddle. Default: 4. + + + Default Brightness Level On for Dimmer. Set custom brightness level (in %) for the dimmer to come on to at single tap. Choose 0 for last brightness level. Default: 0. + + + Sets behavior of the dimmer when physical control is disabled + + + + + Sets behavior of the relay when physical control is disabled + + + + + Set the brightness level the dimmer will turn on to when off and when lower paddle is held DOWN for a second. Default: 20 + + + Normal mode: Upper paddle turns the light on, lower paddle turns the light off. Reverse mode: Upper paddle turns the light off, lower paddle turns the light on. Toggle mode: Either paddle toggles the light. + + + + + - - - - - - - - + + + + + + + +