diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 05701ce19ccb..f5e753882a3f 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/Marlin.cpp b/Marlin/src/Marlin.cpp
index 9720d824facf..e7d4a37fe351 100644
--- a/Marlin/src/Marlin.cpp
+++ b/Marlin/src/Marlin.cpp
@@ -40,6 +40,8 @@
 #include "sd/cardreader.h"
 #include "module/configuration_store.h"
 #include "module/printcounter.h" // PrintCounter or Stopwatch
+#include "feature/closedloop.h"
+
 #ifdef ARDUINO
   #include <pins_arduino.h>
 #endif
@@ -903,6 +905,10 @@ void setup() {
   #if ENABLED(USE_WATCHDOG) // Reinit watchdog after HAL_get_reset_source call
     watchdog_init();
   #endif
+
+  #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+    init_closedloop();
+  #endif
 }
 
 /**
diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h
index 05701ce19ccb..f5e753882a3f 100755
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 196bcea2a9c6..d1a3b68d5de5 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A2/Configuration_adv.h b/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
index 2e3ca3cf3181..9f03da833557 100644
--- a/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h b/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
index 2e3ca3cf3181..9f03da833557 100644
--- a/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
index 7e8b3093534d..0aae0b459fbb 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
index 2db18a1c8b29..ae78b09d9347 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
index 05701ce19ccb..f5e753882a3f 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 931e42658ee0..569de9106fca 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 2f19cb82c612..55b288c6d84c 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
index 564437a5a1fd..5d31d53404ce 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
index c734d1644727..6d99f4eccfcd 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
index 564437a5a1fd..5d31d53404ce 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
index 74dfd980bd9d..b8b5283a93ad 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
index 2c06e048fa82..658c892c78bb 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
index 5219cbdb59a9..3d9d5fe7f931 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
index 16f84ea6d215..27d7764175b8 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
index f9f494947bc4..3380586f7f8f 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
index 2452d8bca3c3..c4b53e9c15bd 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
index 11ab312c368f..70181295c0dd 100644
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
index f9f494947bc4..3380586f7f8f 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Einstart-S/Configuration_adv.h b/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
index 4cfdd7c0322c..c7e0d1e6b60f 100644
--- a/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h
index f114b563e3ea..7efa557ddd4f 100644
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 85e571875dd2..1c439efa83d2 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h b/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h
index a38541d25e4d..1b08edcdb307 100644
--- a/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h
+++ b/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h
@@ -291,6 +291,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index 3fd8d9666c2a..a801220737ff 100644
--- a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -291,6 +291,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index bedd6aae13b9..8db16bd2f395 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index bedd6aae13b9..8db16bd2f395 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
index 2b44b0c0da9a..261ab2b3c7ff 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
index 35447d2f353f..5203f496ace4 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/MakerParts/Configuration_adv.h b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
index b2de733082ac..928ce844eb5e 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
index 8ef550a7d86e..82231d679dcb 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
index 1db6b9e4253c..e35266134702 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 #define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 8e1d2df13e0b..111ebceebf6d 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
index acc9e3d11fe8..4da0dd6fb25b 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
index 4dd0305c66a9..03532f37a192 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h
index 405eec5250a4..dc61216864f5 100644
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
index 22eb8a647bf9..5b48aebf14fc 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/TheBorg/Configuration_adv.h b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
index 45bd6482c8e3..186615ab5620 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
index f9bf3e7e64d7..b6368c87037a 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h b/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
index 08bed247fe03..45710cd5f487 100644
--- a/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
index 8ed4c3f8ea07..ad86e61d2e81 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
index ab14d61d9618..0dd094abfc30 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@@ -300,6 +300,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
index 61e6742a829d..6ee6470a87c1 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index fc62ed6732ea..554d5fd376ca 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index f02ec1b7c11a..827105953fbe 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index f02ec1b7c11a..827105953fbe 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index c4e932d703b8..920222342804 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
index c4e932d703b8..920222342804 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
index c4e932d703b8..920222342804 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
index 0718fb470abb..c9e93722fecd 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@@ -292,6 +292,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
index 74ebb3c3a203..4c78080b6218 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 9f029fa7cf27..620c4b517140 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h
index 43893f4de84e..9c2767b08033 100644
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
index 8e387d1d6843..e762501ba9b5 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h
index 9aa7f5a49d17..567bd706ef95 100644
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/feature/closedloop.cpp b/Marlin/src/feature/closedloop.cpp
new file mode 100644
index 000000000000..2fe60fcf9c8a
--- /dev/null
+++ b/Marlin/src/feature/closedloop.cpp
@@ -0,0 +1,41 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#include "../inc/MarlinConfig.h"
+
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+
+#if !PIN_EXISTS(CLOSED_LOOP_ENABLE) || !PIN_EXISTS(CLOSED_LOOP_MOVE_COMPLETE)
+  #error "CLOSED_LOOP_ENABLE_PIN and CLOSED_LOOP_MOVE_COMPLETE_PIN are required for EXTERNAL_CLOSED_LOOP_CONTROLLER."
+#endif
+
+#include "closedloop.h"
+
+void init_closedloop() {
+  OUT_WRITE(CLOSED_LOOP_ENABLE_PIN, LOW);
+  SET_INPUT_PULLUP(CLOSED_LOOP_MOVE_COMPLETE_PIN);
+}
+
+void set_closedloop(const byte val) {
+  OUT_WRITE(CLOSED_LOOP_ENABLE_PIN, val);
+}
+
+#endif // EXTERNAL_CLOSED_LOOP_CONTROLLER
diff --git a/Marlin/src/feature/closedloop.h b/Marlin/src/feature/closedloop.h
new file mode 100644
index 000000000000..84cec36fe6c2
--- /dev/null
+++ b/Marlin/src/feature/closedloop.h
@@ -0,0 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+void init_closedloop();
+void set_closedloop(const byte val);
diff --git a/Marlin/src/gcode/calibrate/M12.cpp b/Marlin/src/gcode/calibrate/M12.cpp
new file mode 100644
index 000000000000..a4b75e71bda5
--- /dev/null
+++ b/Marlin/src/gcode/calibrate/M12.cpp
@@ -0,0 +1,36 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#include "../../inc/MarlinConfigPre.h"
+
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+
+#include "../gcode.h"
+#include "../../module/planner.h"
+#include "../../feature/closedloop.h"
+
+void GcodeSuite::M12() {
+  planner.synchronize();
+  if (parser.seenval('S'))
+    set_closedloop(parser.value_int()); // Force a CLC set
+}
+
+#endif
diff --git a/Marlin/src/gcode/gcode.cpp b/Marlin/src/gcode/gcode.cpp
index 6682cfbeb94a..063f32999f62 100644
--- a/Marlin/src/gcode/gcode.cpp
+++ b/Marlin/src/gcode/gcode.cpp
@@ -292,6 +292,10 @@ void GcodeSuite::process_parsed_command(
         case 5: M5(); break;                                      // M5 - turn spindle/laser off
       #endif
 
+      #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+        case 12: M12(); break;                                    // M12: Synchronize and optionally force a CLC set
+      #endif
+
       case 17: M17(); break;                                      // M17: Enable all stepper motors
 
       #if ENABLED(SDSUPPORT)
diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h
index cb9e03b58f49..36d8fc3fc34d 100644
--- a/Marlin/src/gcode/gcode.h
+++ b/Marlin/src/gcode/gcode.h
@@ -76,6 +76,7 @@
  * M3   - Turn laser/spindle on, set spindle/laser speed/power, set rotation to clockwise
  * M4   - Turn laser/spindle on, set spindle/laser speed/power, set rotation to counter-clockwise
  * M5   - Turn laser/spindle off
+ * M12  - Set up closed loop control system. More features coming soon. (Requires EXTERNAL_CLOSED_LOOP_CONTROLLER)
  * M17  - Enable/Power all stepper motors
  * M18  - Disable all stepper motors; same as M84
  * M20  - List SD card. (Requires SDSUPPORT)
@@ -438,6 +439,10 @@ class GcodeSuite {
     static void M5();
   #endif
 
+  #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+    static void M12();
+  #endif
+
   static void M17();
 
   static void M18_M84();
diff --git a/Marlin/src/module/planner.cpp b/Marlin/src/module/planner.cpp
index 43f7a40a41f4..4db6e58d4879 100644
--- a/Marlin/src/module/planner.cpp
+++ b/Marlin/src/module/planner.cpp
@@ -1539,7 +1539,14 @@ float Planner::get_axis_position_mm(const AxisEnum axis) {
 /**
  * Block until all buffered steps are executed / cleaned
  */
-void Planner::synchronize() { while (has_blocks_queued() || cleaning_buffer_counter) idle(); }
+void Planner::synchronize() {
+  while (
+    has_blocks_queued() || cleaning_buffer_counter
+    #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+      || !READ(CLOSED_LOOP_MOVE_COMPLETE_PIN)
+    #endif
+  ) idle();
+}
 
 /**
  * Planner::_buffer_steps