diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 0ad2cfd66e78..64258a181a82 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h
index 0ad2cfd66e78..64258a181a82 100644
--- a/Marlin/src/config/default/Configuration.h
+++ b/Marlin/src/config/default/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
index b62bdbf6c9c6..84ed1495e417 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -725,6 +725,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
index 86a004c7d230..0c871f9fcfeb 100644
--- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
+++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h
index 026e99f017ee..d38ac01cd13c 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration.h
@@ -753,6 +753,9 @@
  * readings with inductive probes and piezo sensors.
  */
 #define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 #define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h
index 66155a1c2c5a..632da57bc2a3 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration.h
@@ -712,6 +712,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
index 9f5be051d7aa..10d0be6d5595 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 1aba31cb9993..88fa590cec25 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -705,6 +705,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
index d37b2455fe67..af00bcb79774 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration.h
@@ -705,6 +705,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
index 53eab4f8a88e..517e7921eed1 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h
@@ -693,6 +693,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
index 72df3ba053b5..bd559d2f7d77 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h
@@ -706,6 +706,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
index accb599b5ac2..5e8ff50ed864 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h
@@ -693,6 +693,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h
index 7eaf80d3b00e..40df14b41910 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration.h
@@ -704,6 +704,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
index bafda134798a..eff898141ad9 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h
@@ -715,6 +715,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
index f75125e7a2be..77e11e6e7d1f 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
index 904acfd3c931..5b0a0889e520 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration.h
@@ -724,6 +724,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration.h b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
index e1d892c93387..8eb91439687d 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration.h
@@ -715,6 +715,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
index 9d3d0db73b4f..af703097a67e 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration.h
@@ -709,6 +709,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
index 96e6fa7f4b47..9fbf305737e6 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration.h
@@ -715,6 +715,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h
index f84f2e4df5c3..d4637f1fe631 100644
--- a/Marlin/src/config/examples/Felix/Configuration.h
+++ b/Marlin/src/config/examples/Felix/Configuration.h
@@ -687,6 +687,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
index 4ea9dad16f82..ae304f74582f 100644
--- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h
+++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h
@@ -687,6 +687,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
index d102c58b3e44..6b5c5c8e983e 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -711,6 +711,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
index 8c0ccf1738f1..c8e5e0d03b7c 100644
--- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h
@@ -720,6 +720,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index 962c21ad97ad..d315874c2cc9 100644
--- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 358b0cfe46f2..11650783acab 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
@@ -721,6 +721,9 @@
  * readings with inductive probes and piezo sensors.
  */
 #define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 #define PROBING_FANS_OFF          // Turn fans off when probing
 #define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 8785c67b87af..1d6b250b0845 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
@@ -720,6 +720,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
index 0c4326eb58ed..1d2758ecd2db 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h
@@ -709,6 +709,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration.h b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
index 6002f2f7439b..67712a92140f 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration.h
@@ -717,6 +717,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/MakerParts/Configuration.h b/Marlin/src/config/examples/MakerParts/Configuration.h
index 898d412c79f8..fff251b577fd 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration.h
@@ -725,6 +725,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h
index 2807f8bcac88..84e197f2518d 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h
@@ -725,6 +725,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration.h b/Marlin/src/config/examples/Malyan/M200/Configuration.h
index d780fdcfc0e1..339c4502a12f 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration.h
@@ -704,6 +704,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
index 6f5b82fda79f..d6a7d4c0859a 100644
--- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h
@@ -709,6 +709,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
index b3f44c3e6c82..41b536b21c76 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -709,6 +709,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
index f913fbb7e3d4..5f40c3908cab 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
index bfb19394d277..3cc8104068a5 100644
--- a/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/Marlin/src/config/examples/RepRapPro/Huxley/Configuration.h
@@ -745,6 +745,9 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
index 2a28de571fef..6cee845e8de9 100644
--- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h
index 8ae029ec9349..274dfa2f4e82 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration.h
@@ -703,6 +703,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h
index 22fcbfe0216d..37038757e5ed 100644
--- a/Marlin/src/config/examples/SCARA/Configuration.h
+++ b/Marlin/src/config/examples/SCARA/Configuration.h
@@ -718,6 +718,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/STM32F10/Configuration.h b/Marlin/src/config/examples/STM32F10/Configuration.h
index a9ffdeb5be8d..10b2cb3282d9 100644
--- a/Marlin/src/config/examples/STM32F10/Configuration.h
+++ b/Marlin/src/config/examples/STM32F10/Configuration.h
@@ -708,6 +708,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/STM32F4/Configuration.h b/Marlin/src/config/examples/STM32F4/Configuration.h
index c0e332efe7ac..763600304863 100644
--- a/Marlin/src/config/examples/STM32F4/Configuration.h
+++ b/Marlin/src/config/examples/STM32F4/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h
index 6b63dd0fa13d..d307e2dd1eda 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h
@@ -736,6 +736,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/TheBorg/Configuration.h b/Marlin/src/config/examples/TheBorg/Configuration.h
index fb65f5ed2851..3e77d576dade 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h
index 0504c31cb79f..33adf7a53ca0 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h
@@ -756,6 +756,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Tronxy/X1/Configuration.h b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
index 70dadfeabd59..c48bfb12b653 100644
--- a/Marlin/src/config/examples/Tronxy/X1/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X1/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
index 0619dbd8023c..45eb828c8512 100644
--- a/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/X5S/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
index 8e968f458549..32ab20251ee9 100644
--- a/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
+++ b/Marlin/src/config/examples/Tronxy/XY100/Configuration.h
@@ -716,6 +716,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
index cb43167cee3a..c2f7e72d0d2c 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
index 05af2766101f..7784e4055a0c 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h
@@ -734,6 +734,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
index 1f4d332bb8fb..c49ec753f7b1 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
index 97d0a9b36306..6787408e79a0 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h
index 05930aa05cb0..c3d79d361c6e 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration.h	
@@ -715,6 +715,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
index 6e53e29ecbfa..2e4e8d0b8b36 100644
--- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
+++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h
@@ -705,6 +705,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index e38d504e486d..73bd69972a05 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -787,6 +787,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
index 87d462123312..5e9a71545227 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -787,6 +787,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 2cccb61df475..228fa2f75dd3 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -787,6 +787,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 5ec25b7d0be4..67dd248a91a3 100644
--- a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -792,6 +792,9 @@
  * readings with inductive probes and piezo sensors.
  */
 #define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 #define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h
index 273622447ff8..a3464642f1d5 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration.h
@@ -777,6 +777,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
index 20abb6fce3fb..5a8eb0d80be7 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@@ -777,6 +777,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
index 2cbe131481e4..2eae24eeb616 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@@ -770,6 +770,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
index b98b5f736105..c4a9ec7d427d 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@@ -780,6 +780,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
index e3e4f45d931f..8a3fd065dae3 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -718,6 +718,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h
index 94af68045ea4..fa75a70413ec 100644
--- a/Marlin/src/config/examples/makibox/Configuration.h
+++ b/Marlin/src/config/examples/makibox/Configuration.h
@@ -708,6 +708,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
index 607631b2f3a5..347564c7e110 100644
--- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h
+++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h
@@ -707,6 +707,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
index 61f7ce2a1a2f..b99134350d4c 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h
@@ -700,6 +700,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h
index a2f27f41d583..7971ab651cef 100644
--- a/Marlin/src/config/examples/wt150/Configuration.h
+++ b/Marlin/src/config/examples/wt150/Configuration.h
@@ -710,6 +710,9 @@
  * readings with inductive probes and piezo sensors.
  */
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
+#if ENABLED(PROBING_HEATERS_OFF)
+  //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+#endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
diff --git a/Marlin/src/gcode/control/M80_M81.cpp b/Marlin/src/gcode/control/M80_M81.cpp
index 59ae933221c7..eb300b01db53 100644
--- a/Marlin/src/gcode/control/M80_M81.cpp
+++ b/Marlin/src/gcode/control/M80_M81.cpp
@@ -41,13 +41,13 @@
   #endif
 
   // Could be moved to a feature, but this is all the data
-  bool powersupply_on =
+  bool powersupply_on = (
     #if ENABLED(PS_DEFAULT_OFF)
       false
     #else
       true
     #endif
-  ;
+  );
 
   #if HAS_TRINAMIC
     #include "../../feature/tmc_util.h"
diff --git a/Marlin/src/module/motion.cpp b/Marlin/src/module/motion.cpp
index c2a76836afe2..a9f6898a0547 100644
--- a/Marlin/src/module/motion.cpp
+++ b/Marlin/src/module/motion.cpp
@@ -1056,6 +1056,16 @@ static void do_homing_move(const AxisEnum axis, const float distance, const floa
     }
   #endif
 
+  #if HOMING_Z_WITH_PROBE && HAS_TEMP_BED && ENABLED(WAIT_FOR_BED_HEATER)
+    // Wait for bed to heat back up between probing points
+    if (axis == Z_AXIS && distance < 0 && thermalManager.isHeatingBed()) {
+      serialprintPGM(msg_wait_for_bed_heating);
+      LCD_MESSAGEPGM(MSG_BED_HEATING);
+      while (thermalManager.isHeatingBed()) safe_delay(200);
+      lcd_reset_status();
+    }
+  #endif
+
   // Only do some things when moving towards an endstop
   const int8_t axis_home_dir =
     #if ENABLED(DUAL_X_CARRIAGE)
diff --git a/Marlin/src/module/probe.cpp b/Marlin/src/module/probe.cpp
index 3c1a27cb5525..46b1e328dad8 100644
--- a/Marlin/src/module/probe.cpp
+++ b/Marlin/src/module/probe.cpp
@@ -482,11 +482,26 @@ bool set_probe_deployed(const bool deploy) {
  * @param  fr_mm_s  Feedrate in mm/s
  * @return true to indicate an error
  */
+
+#if HAS_TEMP_BED && ENABLED(WAIT_FOR_BED_HEATER)
+  const char msg_wait_for_bed_heating[25] PROGMEM = "Wait for bed heating...\n";
+#endif
+
 static bool do_probe_move(const float z, const float fr_mm_m) {
   #if ENABLED(DEBUG_LEVELING_FEATURE)
     if (DEBUGGING(LEVELING)) DEBUG_POS(">>> do_probe_move", current_position);
   #endif
 
+  #if HAS_TEMP_BED && ENABLED(WAIT_FOR_BED_HEATER)
+    // Wait for bed to heat back up between probing points
+    if (thermalManager.isHeatingBed()) {
+      serialprintPGM(msg_wait_for_bed_heating);
+      LCD_MESSAGEPGM(MSG_BED_HEATING);
+      while (thermalManager.isHeatingBed()) safe_delay(200);
+      lcd_reset_status();
+    }
+  #endif  
+
   // Deploy BLTouch at the start of any probe
   #if ENABLED(BLTOUCH)
     if (set_bltouch_deployed(true)) return true;
diff --git a/Marlin/src/module/probe.h b/Marlin/src/module/probe.h
index cfc3141e024b..eceb1bb92484 100644
--- a/Marlin/src/module/probe.h
+++ b/Marlin/src/module/probe.h
@@ -44,6 +44,9 @@
   float probe_pt(const float &rx, const float &ry, const ProbePtRaise raise_after=PROBE_PT_NONE, const uint8_t verbose_level=0, const bool probe_relative=true);
   #define DEPLOY_PROBE() set_probe_deployed(true)
   #define STOW_PROBE() set_probe_deployed(false)
+  #if HAS_TEMP_BED && ENABLED(WAIT_FOR_BED_HEATER)
+    extern const char msg_wait_for_bed_heating[25];
+  #endif
 #else
   #define DEPLOY_PROBE()
   #define STOW_PROBE()